关于微分熵的一类强偏差定理

利用关于乘积分布密度的相对熵和相对熵率的概念,建立了相依连续型随机变量序列关于参考微分熵的一类强偏差定理,证明中给出了将Laplace变换应用于微分熵强偏差定理的研究的一种途径．     

BLOW-UP RESULTS AND ASYMPTOTIC BEHAVIOR OF THE EMDEN-FOWLER EQUATION u＂ = ｜u｜^p

In this article the author works with the ordinary differential equation u＂ = ｜u｜^p for some p 〉 0 and obtains some interesting phenomena concerning blow-up, blow-up rate, life-span, stability, instability, zeros and critical points of solutions to this equation.     

稀薄气体二维外部柱体绕流特性研究

本文采用直接模拟蒙特卡罗方法对稀薄气体二维外部柱体绕流问题进行了数值模拟。结果表明:外部绕流问题,在特定情况下会产生激波,激波的产生,不仅与气体的稀薄程度有关,还与来流马赫数有关。而气流与壁面之间的换热,随来流马赫数增加而增加,随气体稀薄程度增加而减小。     

环形燃烧室火焰简及旋流器流场计算

本文采用偏微分方程法生成贴体网格,在任意曲线坐标系下数值研究两种先进燃烧室火焰筒及其旋流器三维紊流流场。由于旋流器的形状复杂,本文采用型线定点法确定网格的边界。在非交错网格系下采用SIMPLE算法和混合差分格式对离散方程进行求解。计算结果表明计算方法合理,这计算程序进一步扩展,可用来预估环形燃烧室反应流流场。     

Interior point cutting plane method for optimal power flow

In this paper, an interior point cutting plane method (IPCPM)is applied to solve optimal power flow (OPF) problems. Comparedwith the simplex cutting plane method (SCPM), the IPCPM is simpler,and efficient because of its polynomial-time characteristic.Issues in implementing IPCPM for OPF problems are addressed,including (1) how to generate cutting planes without using thesimplex tableau, (2) how to identify the basis variables inIPCPM, and (3) how to generate mixed integer cutting planes.The calculation speed of the proposed algorithm is further enhancedby utilizing the sparsity features of the OPF formulation. Numericalsimulations on IEEE 14-300-bus test systems have shown thatthe proposed method is effective.     

低进汽压力下超音速两相流升压特性实验研究

本文采用实验方法研究了进汽压力为0.2 MPa以下时,由蒸汽喷嘴、混合腔及相应的阀门和管道组成超音速汽液两相流升压加热装置的运行特性。实验表明在进汽压力为0.1 MPa-0.2 MPa时,超音速汽液两相流升压加热装置都可稳定可靠地运行,且升压效果明显,可满足电力、供暖、轻工等许多行业蒸汽加热的要求。     

某轴流压气机叶尖间隙效应实验研究

本文对某低速轴流压气机叶尖间隙尺度对性能的影响进行了实验研究,并通过不同的机匣结构情况研究一种叶尖漏流不敏感机匣。实验表明,不同的间隙尺度对叶轮机总体性能存在十分明显的影响。对绝大部分运行状态,小间隙下的压升和效率均明显高于大间隙的情况。另外,所采用的毛刷式和篦齿式的机匣实验结果表明,不论毛刷式还是篦齿式机匣,在大流量负攻角情况下对性能的影响不大,但毛刷式机匣并不能达到提高失速裕度的目的,而篦齿式机匣在小流量情况下对压升有所提高,但对效率影响不大。     

热丝加热电流对CH薄膜沉积速率和表面形貌的影响

 热丝辅助裂解法是结合气相沉积制备聚对二甲苯薄膜和热丝化学气相沉积而形成的一种制-CH薄膜的新方法。热丝辅助裂解法的最大特点就是在保持低衬底温度情况下可以获得高沉积速率，而热丝加热电流对薄膜沉积速率和薄膜表面形貌具有重要影响。研究表明，热丝加热电流越大，薄膜沉积速率越高，在加热电流9A时，薄膜沉积速率可达0.002mm/min，同时薄膜表面粗糙度随之增加，薄膜表面也开始出现其它元素污染，因此，一般热丝加热电流选择为7A附近。     

On the Second Law of Thermodynamics and the Piston Problem

The piston problem is investigated in the case where the length of the cylinder is infinite (on both sides) and the ratio m/M is a very small parameter, where m is the mass of one particle of the gaz and M is the mass of the piston. Introducing initial conditions such that the stochastic motion of the piston remains in the average at the origin (no drift), it is shown that the time evolution of the fluids, analytically derived from Liouville equation in a previous work, agrees with the Second Law of thermodynamics. We thus have a non equilibrium microscopical model whose evolution can be explicitly shown to obey the two laws of thermodynamics.     

非线性不适定问题一种双循环的牛顿型迭代格式

本文研究非线性算子方程F(x)=y的解,结合最速下降法,Newton-Landweber迭代格式及正则化思想,在F满足适当的条件下,构造出新的双循环迭代格式。本文对格式的收敛性进行了严格论证,并估计出迭代格式的收敛精度。