微纳米加工技术及其应用综述

材料与结构在微纳米尺度展现了许多不同于宏观尺度的新特征，纳米技术已经成为当前科学研究与工业开发的热门领域之一。微小型化依赖于微纳米尺度的功能结构与器件，实现功能结构微纳米化的基础是先进的微纳米加上技术，文章对微纳米加上技术做了一个综合的介绍，简要说明了微纳米加工技术与传统加工技术的区别，在微纳米加工技术的应用方面提出了一些合理选择加工技术的原则，并对当前微纳米加工技术面临的挑战和今后发展的趋势作了预测。     

The efficacy of tilted axial MRI of the CNS

The angle between the straight axial plane and the orbito-meatal line was measured in 156 consecutive magnetic resonance examinations. Inconsistent head positioning caused this angle to vary by as much as 44 degrees. Careful positioning of the patient by the technologist can minimize this variability, leading potentially to improved image interpretation. To assess the merit of a standardized orientation for MR examinations of the head, straight axial and tilted axial MR scans were compared in 34 patients. The tilted images were obtained parallel to the orbito-meatal line and were found to be superior for visualization of the cerebellum. When correlative x-ray CTs are available or when an abnormality in the posterior fossa is suspected, tilted axial MR scans should be employed.     

综合网管中基于模型驱动的元数据管理

提出了一种基于模型驱动的元数据管理方案．方案采用了基于模型的形式化描述方法，统一了专业网管子系统间的元数据模式；通过引入模型驱动技术，从元模型的抽象层次消除了不同专业网管子系统之间存在的“信息孤岛”；方案还对综合网管环境下的元数据理论和交换机制进行了研究，并给出了元数据的管理框架以及元数据交换的Java接口映射．     

掺铒光纤放大器中上转换过程的影响

掺杂浓度的提高影响了掺铒光纤放大器(EDFA)的性能,对经典Giles模型提出了新的要求。首先研究了高掺杂下铒离子距离较小引起的上转换过程的机理,通过优化速率方程模型分析了上转换过程对EDFA的影响,得出了在泵浦光和信号光远远大于ASE光的假设下泵浦光和信号光沿光纤长度变化的近似表达式,并将该近似分析解与解析解进行了比较。仿真结果表明上转换过程会降低随光纤传输的信号光和泵浦光,影响EDFA的放大性能,并得出了当掺铒浓度大于2.95×1025m-3时,上转换过程的影响不能忽略的结论。     

自由曲面光学虚拟制造与检测系统的探讨

自由曲面光学产品设计、制造与检测的工艺流程，通常采取试凑法逐次逼近。由于加工 检测 再加工，循环往复，既费时，成本又高，产生了瓶颈问题。为了解决此弊端，本文运用虚拟制造技术，提出光学虚拟制造的基本构想，即虚拟制造系统结构模型，给出光学系统虚拟原型的构成和光学系统成像质量虚拟检测系统的构成，讨论光学成像质量的仿真检测以及敏度分析方法。研究结果表明：运用虚拟制造与检测技术，可缩短研发周期，降低成本，优化工艺并提高产品质量。     

The origin of the formation of cavities in galvanized coatings

The role of water‐soluble corrosion products on galvanized wires was examined. The samples used were industrial hot‐dip galvanized wires, which were exposed to the open air under all weather conditions for a relatively short time (6 and 12 months), in an urban environment close to the sea. The samples were studied by different methods, i.e. scanning electron microscopy (SEM), transmission electron microscopy (TEM), X‐ray diffraction (XRD) and optical microscopy (OM). Several phases were detected because of the galvanization procedure and the steel substrate. Furthermore, phases which were formed as a result of the reaction of zinc with the atmosphere were also detected. These were oxides like ZnO, carbonates like ZnCO₃ and hydrated Zn and Fe sulfates. Their presence influences the corrosion resistance of the wires, which finally, strongly depends on the solubility of the wires in water. The SO₄^2? compounds especially are very soluble and consequently are easily removed from the coating surface, leading to its degradation by the formation of cavities. In any case, their presence, even after a short period of exposure, implies that the coating is highly affected by the atmosphere of the modern city. Copyright © 2006 John Wiley & Sons, Ltd.     

金刚石窗口冷却Yb3+∶YAG DPSSL设计

针对高功率二极管重复率抽运的V型非稳腔Yb3+∶YAG激光头，提出了利用金刚石窗口冷却和直接水冷相结合的复合冷却设计.在YAG片的抽运面进行直接水冷，同时在激光提取面利用金刚石窗口冷却介质.金刚石优异的导热性能不仅能够有效地冷却激光介质，还能消除横向的温度梯度，解决了高功率激光器冷却和高功率抽运的矛盾.模拟结果表明对掺杂10 at %厚度为1.6 mm的Yb3+∶YAG片在抽运功率密度为20 kW/cm2，重复频率为10 Hz的条件下，要将最高温度控制在可接受的范围内（比如320 K），周围冷却水的对流换热系数约为4000 W/m2K.     

二维磁结构的扫描隧道显微术研究

文章介绍了近年来利用扫描隧道显微术（STM）对表面和薄膜磁结构的研究进展。二维或表面磁结构可以通过在非磁性单晶上外延磁性单原子层薄膜形成，也可以在清洁的磁性单晶表面形成。利用磁性的STM针尖可以观测到原子分辨的表面磁结构。这将增进人们从纳米尺度对磁性的理解，并推动磁电子学的发展。