双面电弧焊接的传热模型

将等离子焊接(PAW)电弧和钨极氩弧焊(TIG)电弧串接,相对作用于工件的正反面形成双面电弧焊接(DSAW)系统,可以引导焊接电流沿工件厚度方向流过小孔,补偿等离子电弧穿透工件时消耗的能量,以有效地提高等离子弧的穿透能力.综合考虑影响双面电弧焊接正反面熔池几何形状的力学因素,建立了熔池表面变形的控制方程,以此为基础并采用帖体曲线坐标系建立了DSAW焊接传热的数学模型,分析了DSAW,PAW焊接传热的差异,从传热的角度解释了DSAW焊接熔深增加的原因.焊接工艺实验表明,计算结果与实测结果吻合良好. 关键词： 双面电弧焊接(DSAW) 传热模型 熔池表面变形模型     

q变形对相干态的相位概率分布特性

通过推广Pegg和Barnett的相位算符和相位态到q变形的双模情况, 应用数值计算 研究了q变形对相干态的相位概率分布特性. 结果表明, q变形对相干态的相位概率分布受到相位参数、q参数和参数│ξ│的调节, 从而反映出不同的量子相干特性.     

Deformation Morphology underneath the Vickers Indent in Bulk Metallic Glasses

Plastic deformation behaviour of Zr52.5Al10Ni10Cu15Be12.5 and Mg65Cu25Gd10 bulk metallic glasses (BMGs) is studied by using the depth-sensing nanoindentation and microindentation. The subsurface plastic deformation zone of the BMGs is investigated using the bonded interface technique. Both the BMGs exhibit the serrated flow depending on the loading rate in the loading process of indentation. Slow indentation rates promote more conspicuous serrations, and rapid indentations suppress the serrated flow. Mg-based BMG shows a much higher critical loading rate for the disappearance of the serration than that in Zr-based BMG. The significant difference in the shear band pattern in the subsurface plastic deformation zone is responsible for the different deformation behaviour between the two BMGs. Increase of the loading rate can lead to the increase of the density of shear bands. However, there is no distinct change in the character of shear bands at the loading rate of as high as1000 nm/s.     

Small Stress Change Triggering a Big Earthquake： a Test of the Critical Point Hypothesis for Earthquakes

Whether or not a small stress change can trigger a big earthquake is one of the most important problems related to the critical point hypothesis for earthquakes. We investigate global earthquakes with different focM mechanisms which have different levels of ambient shear stress. This ambient stress level is the stress level required by the earthquakes for their occurrence. Earthquake pairs are studied to see whether the occurrence of the preceding event encourages the occurrence of the succeeding one in terms of the Coulomb stress triggering. It is observed that the stress triggering effect produced by the change of Coulomb failure stress in the same order of magnitudes,about 10-2 MPa, is distinctly different for different focal mechanisms, and thus for different ambient stress levels.For non-strike-slip earthquakes with a relatively low ambient stress level, the triggering effect is more evident,while for strike-slip earthquakes with a relatively high ambient stress level, there is no evident triggering effect.This water level test provides an observational support to the critical point hypothesis for earthquakes.     

加热炉内板坯粘塑性下桡变形的研究

在加热妒内，由于高温及重力作用，板坯两端的悬臂将产生下桡变形。悬臂越长，下桡将越大，导致悬臂下桡部分与出口端墙相碰，影响出料而造成事故。本文对加热炉内板坯的下桡变形进行了分析计算。首先，建立了板坯的二维非稳态导热模型并用有限差分法计算了炉内板坯随时间的温度变化；然后建立了板坯悬臂粘塑性变形模型，用有限元法计算了高温条件下由重力引起的悬臂的下桡变形。由此理论模型计算出的板坯抽出温度与悬臂端下桡量与实测结果吻合良好，说明该理论模型及模型计算方法是正确的，可用于对装钢生产进行指导。     

核结构数据库(NSDB)

基于最新的实验评价和模型计算的核结构数据, 组建了一个更新的核结构数据库(NSDB), 目前,该数据库包括稳定同位素的丰度和原子质量, 原子核基态和分离激发态的性质, 及原子核的变形、半径及其它性质等三部分的数据.     

混合曲率曲面变形方程的Tricomi问题——Ⅱ.解的存在性

本文在很弱的条件下,证明对混合曲率曲面无穷小变形方程的Tricomi问题,存在L₂弱解和H₁强解。     

激光散斑法对预制缺口岩石的缝端微裂区变形过程研究

本文应用激光散斑法对预制缺口岩石的缝端微裂区进行了无接触位移测量,求得加裁点位移 d 和缝端张开位移η.通过对主裂缝的跟踪量测,表明该试件的裂缝在失稳前存在着亚临界扩展.在此阶段,预制裂缝缝端主裂缝的形式推测主要是类似“啮合”裂缝及部分张开裂缝,当缝端张开位移达到临界值时,荷载稍增,裂缝即快速扩展,以致发生断裂.     

二元光学波面变形器件的研究

基于计算全息原理设计了二元光学波面变形器件，一块二元光学器件的衍射效率比计算全息可提高４倍，高斯波面整形需要二块整形光学器件，二元光学器件的激光利用率比计算全息提高１６倍，而且制做工艺简单．