煤直接液化油中混合酚的分离研究

利用分子筛择形特点，对煤直接液化油中的混合酚实施高效分离。本研究选取间甲酚和对甲酚作为分离煤直接液化油馏分段混合酚的模型化合物，采用化学液相沉积法对HZSM-5吸附剂的孔口结构进行改变，分析分子筛硅铝比及颗粒粒径对模型化合物间甲酚和对甲酚吸附分离性能的影响，以获得高性能固相吸附剂，并将其应用于180-190℃馏分段混合酚分离。结果表明，当分子筛硅铝比为25、粒径为3-5 μm时，分子筛的孔口结构调节效果最优；当正硅酸乙酯的最小用量为0.2 mL/g时，固相吸附剂的吸附量为0.03 g/g，对甲酚选择性高于95%。由于外表面沉积物对吸附剂的孔口结构变化，导致对甲酚选择性的提高。进一步采用HZSM-5（1）吸附剂对真实煤直接液化油混合酚的分离中发现，苯酚和对甲酚的选择性均达到100%。     

Can a Procedure for the Growth of Single-layer Graphene on Copper be used in Different Chemical Vapor Deposition Reactors?

In the last decade, catalytic chemical vapor deposition (CVD) has been intensively explored for the growth of single-layer graphene (SLG). Despite the scattering of guidelines and procedures, variables such as the surface texture/chemistry of catalyst metal foils, carbon feedstock, and growth process parameters have been well-scrutinized. Still, questions remain on how best to standardize the growth procedure. The possible correlation of procedures between different CVD setups is an example. Here, two thermal CVD reactors were explored to grow graphene on Cu foil. The design of these setups was entirely distinct, one being a “showerhead” cold-wall type, whereas the other represented the popular “tubular” hot-wall type. Upon standardizing the Cu foil surface, it was possible to develop a procedure for cm²-scale SLG growth that differed only by the carrier gas flow rate used in the two reactors.     

pH-Sensitive Oscillatory Motion of a Urease Motor on the Urea Aqueous Phase

A self-propelled object coupled with an enzyme reaction between urease and urea was investigated at the air/aqueous interface. A plastic object that was fixed to a urease-immobilized filter paper was used as a self-propelled object, termed a urease motor, placed on an aqueous urea solution. The driving force of the urease motor is the difference in the surface tension around the object. Oscillatory motion or no motion was triggered depending on the initial pH of the urea solution. Both the frequency and maximum speed of the oscillatory motion varied depending on the initial pH of the water phase. The mechanisms underlying the oscillatory motion and no motion were discussed in relation to the bell-shaped enzyme activity of urease in the enzyme reaction and the surface tension around the urease motor.     

A survey of surface tension,molar volume and density for Sn–Ag–Cu–Bi–Sb quinary alloys as lead-free solders

ABSTRACT

By applying the geometric models and the theoretical equation, the surface tension, the molar volume and the density were studied. The empirical calculations were carried out in temperature range 623?K?≤?T?≤?1123?K. Only few thermophysical properties were estimated for eight quinary alloys: Sn3.55Ag0.5Cu3Bi3Sb, Sn3.48Ag0.5Cu3Bi5Sb, Sn3.48 Ag0.5Cu5Bi3Sb, Sn3.40 Ag0.5Cu5Bi5Sb, Sn3.53Ag1Cu3Bi3Sb, Sn3.46Ag1Cu3Bi5Sb, Sn3.46Ag1Cu5Bi3Sb, Sn3.38Ag1Cu5Bi5Sb. The results show that surface tension and density have a linear appearance for all temperatures. We have also studied the influence of the composition and temperature in the studied alloys. The obtained theoretical results are compared with the experimental ones and with the conventional Pb–Sn welds.     

Response surface methodology toward the optimization of high-energy carotenoid extraction from Aristeus antennatus shrimp

High-energy assisted extraction techniques, like ultrasound assisted extraction (UAE) and microwave assisted extraction (MAE), are widely applied over the last years for the recovery of bioactive compounds such as carotenoids, antioxidants and phenols from foods, animals and herbal natural sources. Especially for the case of xanthophylls, the main carotenoid group of crustaceans, they can be extracted in a rapid and quantitative way with the use of UAE and MAE.     

化学法改性煤沥青脱除苯并芘的研究

在管式反应器中采用苯甲酸、聚乙二醇、固体古马隆树脂（S）、液体古马隆树脂（L）为添加剂来降低煤沥青中有害物质苯并芘的含量，以期使得煤沥青可绿色化应用。采用紫外-可见分光光度计分析煤沥青中苯并芘含量。考察了反应温度、反应时间、添加剂添加量、催化剂等工艺条件对添加剂脱除煤沥青中苯并芘的影响。结果表明，不同工艺条件能降低煤沥青中苯并芘的含量。在优化条件下，不同添加剂对苯并芘脱除率由高到低依次为：液体古马隆树脂、聚乙二醇、苯甲酸和固体古马隆树脂。分析其反应机理，这与催化剂的酸性相关，发生亲电取代反应。结果表明，液体古马隆树脂（L）在催化剂存在下对煤沥青中苯并芘脱除率可达73.0%，显示了良好的应用前景。     

A Biosilification Fusion Protein for a ‘Self‐immobilising’ Sarcosine Oxidase Amperometric Enzyme Biosensor

Monomeric sarcosine oxidase (mSOx) fusion with the silaffin peptide, R5, designed previously for easy protein production in low resource areas, was used in a biosilification process to form an enzyme layer electrode biosensor. mSOx is a low activity enzyme (10–20 U/mg) requiring high amounts of enzyme to obtain an amperometric biosensor signal, in the clinically useful range <1 mM sarcosine, especially since the K_m is >10 mM. An amperometric biosensor model was fitted to experimental data to investigate dynamic range. mSOx constructs were designed with 6H (6×histidine) and R5 (silaffin) peptide tags and compared with native mSOx. Glutaraldehyde (GA) cross‐linked proteins retained ～5 % activity for mSOx and mSOx‐6H and only 0.5 % for mSOx‐R5. In contrast R5 catalysed biosilification on (3‐mercaptopropyl) trimethoxysilane (MPTMS) and tetramethyl orthosilicate (TMOS) particles created a ‘self‐immobilisation’ matrix retaining 40 % and 76 % activity respectively. The TMOS matrix produced a thick layer (>500 μm) on a glassy carbon electrode with a mediated current due to sarcosine in the clinical range for sarcosinemia (0–1 mM). The mSOx‐R5 fusion protein was also used to catalyse biosilification in the presence of creatinase and creatininase, entrapping all three enzymes. A mediated GC enzyme linked current was obtained with dynamic range available for creatinine determination of 0.1–2 mM for an enzyme layer ～800 nm.     

A Shell-by-Shell Approach for Synthesis of Mesoporous Multi-Shelled Hollow MOFs for Catalytic Applications

Over the past two decades, advanced materials with hollow interiors have received significant attention in materials research owing to their great application potential across a vast number of technological fields. Though with great difficulty, multi-shelled hollow metal–organic frameworks (MSHMs) have also been successfully synthesized in recent years. Herein, a rational shell-by-shell soft-templating protocol has been devised to fabricate highly uniform multi-shelled hollow cobalt-imidazole-based MOF (ZIF-67). For the first time, it has become possible to endow mesoporosity to this new type of functional material (i.e., mesoporous MOFs). When used as carrier materials in catalytic reactions, in principle, these mesoporous MSHMs with high surface area not only improve the dispersity of metal nanoparticles (NPs), but also efficiently facilitate the mass diffusion of the reactions, resulting in enhanced catalyst activity. Moreover, the obtained MSHMs/M nanocomposites serve as base-metal bifunctional catalysts for one-pot oxidation-Knoevenagel condensation cascade reaction, in which the MSHMs itself serves as a pristine active catalyst in addition to its role of catalyst support. The results demonstrate that excellent multifunctional catalysts can be achieved via preparing intrinsically microporous bulk MOFs into extrinsically mesoporous MSHMs which possess many structural merits that conventional bulk MOFs do not have.     

Electrocatalysis in confined space

The complex interplay of restricted mass transport leading to local accumulation or depletion of educts, intermediates, products, counterions and co-ions influences the reactions at the active sites of electrocatalysts when electrodes are rough, three-dimensionally mesoporous or nanoporous. This influence is important with regard to activity, and even more to selectivity, of electrocatalytic reactions. The underlying principles are discussed based on the growing awareness of these considerations over recent years.