陶瓷刀具切削区温度场的计算机模拟

在切削金属过程中所消耗的能量几乎９０％以上都转化为热，致使工件，切屑和刀具的温度都上升，其中刀具的温升与切削机理及切削参数密切相关，并且直接影响刀具磨损及其全用寿命。为了研究陶瓷刀具切削温度分布对其磨损规律和机理的影响，根据传热理论建立了数学模型，用计算机模拟编制出陶瓷刀具切削区温度场计算的专业软件，可以得出不同陶瓷料刀具在不同切削条件下切步同工件材料过程中的温度分布曲线图，而且实际测量值与模拟值     

氮化硅陶瓷平板振动模态参数的研究

本文采用压电陶瓷片测振技术,试验分析了氮化硅陶瓷平板的固有频率及模态阻尼比,试验结果与有限元计算结果比较吻合。本文还对氮化硅陶瓷平板与普通钢平板做了对比试验,结果表明氮化硅陶瓷平板的固有频率及模态阻尼比都较高。     

陶瓷阻力曲线测定的新方法——断裂栅法

将零厚度单向试件栅刻蚀工艺应用于晶须增韧氮化硅陶瓷基复合材料表面，通过记录试件所在桥路的输出电压值，可得到随载荷不断增大裂纹逐渐向前扩展过程中每一时刻的裂尖位置和裂纹长度，从而得到该种材料的阻力曲线。     

Micromechanics of residual stress and texture development due to poling in polycrystalline ferroelectric ceramics

This paper presents micromechanics based analysis of elastic strain and changes in the texture of poled polycrystalline ferroelectric PZT ceramics for direct comparison with synchrotron X-ray measurements. The grains are modelled as spherical inclusions, to which transformation strains are assigned depending on the fractions of different ferroelectric domains. Eshelby's inclusion problem with the classical self-consistent method is applied to evaluate the elastic state of the grains. In particular, the elongation due to lattice elastic strain is calculated as a function of inclination Ψ relative to the polar axis. The ratio of diffraction peak intensities, corresponding to the domain fractions, is also expressed as a function of Ψ. This analysis identifies the special character of the reflection, for which the lattice strain along in the stress free state is independent of ferroelectric domain population and hence unaffected by poling. The elongation due to the lattice strain parallel to and peak intensity ratio are expressed in terms of the overall macroscopic strain of a poled specimen, each having a dependence.     

Al2O3陶瓷复合靶抗长杆弹侵彻性能和机理实验研究

用DOP(depthofpenetration)实验研究了质量分数为 90 %的Al2 O3 陶瓷复合靶抗长杆弹侵彻性能。实验表明 :随陶瓷厚度的增加 ,以差分效益系数和靶平均阻力表征的陶瓷复合靶的抗长杆弹侵彻性能降低 ;盖板能增强陶瓷复合靶抗侵彻性能。对回收陶瓷和盖板的破坏特征分析表明 :长杆弹对陶瓷复合靶侵彻过程大致可分为初期侵彻和稳定侵彻两个阶段 ,但对薄靶和厚靶 ,两个阶段在整个侵彻过程中所占比重不同。     

非均匀铁弹畴变对离面极化压电陶瓷应力强度因子的影响研究

基于文献中报道的试验结果，本文考虑非均匀的畴变过程区，它包含一个位于中心的饱和区和环绕饱和区的渐变区．为了描述外加应力引起的部分铁弹畴变，本文采用一个显式的基于最小能量原理的非均匀畴变准则．考虑离面极化的压电陶瓷，假设其初始极化矢量平行于离面方向．畴变后的电畴位于面内，具体方位由最大释放功来确定．基于非均匀畴变准则，本文给出了裂尖处非均匀畴变区几何及畴变体积分数的分布．并在静止裂纹和稳态扩展裂纹两种特殊情况下计算了铁弹畴变对裂尖处应力强度因子的影响．结果表明：(1) 静止裂纹尖端处的畴变减小了材料的起裂强度；(2) 准静态稳态裂纹附近的畴变增加了材料的断裂强度．且理论预测的R曲线渐近值与试验结果定量吻合．     

TiB2增强Al2O3陶瓷刀具高速干切削摩擦磨损性能

采用TiB2增强Al2O3陶瓷刀具对淬硬钢进行高速干切削试验,利用切削高温作用下的摩擦化学反应,在刀具表面原位生成具有润滑作用的反应膜,从而实现Al2O3/TiB2陶瓷刀具的自润滑.结果表明:低速干切削时,Al2O3/TiB2陶瓷刀具的磨损机制主要表现为粘着磨损和磨料磨损;而在高速干切削时,刀具的磨损机制主要表现为氧化磨损,刀具表面经由氧化反应生成具有润滑作用的反应膜而起到固体润滑作用,从而使刀具的耐磨性能提高,随着TiB2含量和切削速度的增加,反应膜的减摩抗磨作用增强;而在切削区通入氮气时,由于刀具表面氧化膜形成受阻,刀具的抗磨能力有所降低.     

Radiative heat transfer augmentation of natural gas flames in radiant tube burners with porous ceramic inserts

Experiments were conducted using porous ceramic inserts to enhance the radiative heat transfer from natural gas flames in a straight-through radiant tube burner. The performance of the radiant tube burner with partially stabilized zirconia and silicon carbide inserts is compared to a baseline case of no inserts at three levels of combustion air preheat. Spectral intensities, temperatures within the radiant tube burner, tube wall temperatures, and exhaust temperatures were measured to determine the effectiveness of the enhanced heat transfer due to the inserts. Exhaust emission constituents were also measured to determine the effect that the inserts have on exhaust products. NO_x emissions are reduced by up to 30% with the inserts. The silicon carbide inserts have higher spectral intensities and total radiative energy transfer than partially stabilized zirconia inserts. Both inserts have enhanced radiant heat transfer compared to the no-insert configuration, with the radiative enhancement due to inserts as great as five times that of the no-insert configuration. The net result is increased tube wall temperatures and decreased exhaust temperatures with the ceramic inserts.     

Al_2O_3 基陶瓷摩阻材料的摩擦磨损特性

在ＭＧ－２００磨损试验机上，对以Ａｌ２Ｏ３为基体，分别添加固体润滑剂组元石墨和氮化硼制备的２种陶瓷摩阻材料的摩擦磨损特性进行了试验研究．结果表明：在给定的试验条件下，添加石墨或氮化硼都可以改善材料摩擦性能的稳定性；分别在１００℃，２００℃，３００℃和４００℃下定温试验时，这２种摩阻材料都具有较高的摩擦因数和良好的耐磨性，其中含氮化硼之摩阻材料的耐磨性比含石墨之摩阻材料的更好，前者在４００℃时的磨损率仅为后者在同温时的１／２．     

A NEW METHOD TO DETERMINE THE R-CURVE OF CERAMICS-FRACTURE GRATING METHOD

The etching technique of the single-lined zero-thickness specimen grating is applied tothe surface of the SiC fiber toughening Si_3N_4 ceramic composite specimen.The position of the crackand the crack length during the process of crack extension when the load is applied and gradually in-creased can be determined by recording the output voltage value of the Wheatstone bridge in which theceramic specimen with the fracture grating on is located.The crack-growth-resistance(R-curve) of thismaterialis thus obtained.