Electrochemical characterization of poly(vinylidenefluoride)-zinc triflate gel polymer electrolyte and its application in solid-state zinc batteries

Gel polymer electrolyte (GPE) films comprising of poly(vinylidenefluoride), propylene carbonate, ethylene carbonate and zinc trifluoromethane sulfonate are prepared and characterized. The composition of GPE is optimized to contain minimum liquid components with a maximum specific conductivity of 3.94×10⁻³ S cm⁻¹ at (25±1) °C. A detailed investigation on the properties such as ionic conductivity, transport number, electrochemical stability window, reversibility of Zn/Zn²⁺ couple and Zn/gel electrolyte interfacial stability have been carried out. The ionic conductivity follows a VTF behaviour with an activation energy of about 0.0014 eV. Cationic transport number varies from 0.51 at 25 °C to 0.18 at 70 °C. Several cells have been assembled with GPE as the electrolyte, zinc as the anode, γ-MnO₂ as the cathode and their charge–discharge behaviour followed. Capacity values of 105, 82, 64 and 37 mAh/g of MnO₂ have been achieved at 10, 50, 100 and 200 μA/cm² discharge current densities, respectively. The discharge capacity values are almost constant for about 55 cycles for all values of current densities. Cyclic voltammetric study of MnO₂ electrode in Zn/GPE/MnO₂ cell clearly shows intercalation/deintercalation of Zn²⁺.     

On the role of the interface charge in non-ideal metal–semiconductor contacts

The bias dependent interface charge is considered as the origin of the observed non-ideality in current–voltage and capacitance–voltage characteristics. Using the simplified model for the interface electronic structure based on defects interacting with the continuum of interface states, the microscopic origin of empirical parameters describing the bias dependent interface charge function is investigated. The results show that in non-ideal metal–semiconductor contacts the interface charge function depends on the interface disorder parameter, density of defects, barrier pinning parameter and the effective gap center. The theoretical predictions are tested against several sets of published experimental data on bias dependent ideality factor and excess capacitance in various metal–semicoductor systems.     

Investigation of the Li1+xV3O8 electrode–organic electrolyte interface by scanning photoelectron microscopy

To investigate the formation of a solid electrolyte interface (SEI) on the Li_1+xV₃O₈ electrode surface in the thermodynamic stability range of the organic electrolyte, we applied scanning photoelectron microscopy (SPEM) to a pristine electrode and to an electrode after ten cycles. The F K-edge absorption spectrum of the cycled electrode showed that LiF forms on the electrode surface during the lithium insertion–extraction process in the Li_1+xV₃O₈/Li cell. The photoelectron spectrum for the cycled electrode showed intense spectral features corresponding to Li 1s, F 2s, F 2p, and P 2p electron signals, whereas these spectral features were of negligible intensity for the pristine electrode. The above results give strong support for the formation of an SEI that consists of LiF and compounds containing phosphorus during operation of the battery. The SPEM images also revealed that the fluorine distribution on the surface of the cycled electrode was inhomogeneous.     

Theoretical Studies on the Si（001）-SiO2 Interface Structure

1 INTRODUCTION Silicon and its alloy have been widely applied in such fields as electronic industry, high-temperature structural ceramics, etc. In addition, the researches on silicon and its relevant materials greatly promote the rapid development of modern optics and infor- mation technology. Therefore, more and more at- tention is focused on the structure of silicon, oxide of silicon and the interfaces between silicon and metal or nonmetal. As an ideal passive film on the Si surface, S…     

Statistical Analysis of the Effect of Mineral Admixtures on the Strength of the Interfacial Transition Zone

Microscopic evidence indicates that the thickness of the interfacial transition zone (ITZ) between the aggregate and the cement paste is modified when mineral admixtures partially replace portland cement. Unfortunately, there is limited information on the significance of these microscopic modifications to the mechanical properties of the ITZ. This research reports experimental results on the shear and tensile strength of the ITZ as affected by the addition of the following mineral admixtures: silica fume, fly ash, and natural pozzolan. Statistical analysis was used to identify the significant parameters affecting the tensile and shear strength of the ITZ. Experimental results indicate that not only does the incorporation of silica fume and fly ash increase the strength of the ITZ, these mineral admixtures have a greater influence on the strength increase of the ITZ than in the strength increase of the cement paste.     

Macrodefect-Free Materials: Modification of Interfaces in Cement Composites by Polymer Grafting

MDF materials are chemically bonded ceramic materials free of the macrodefects typical of hydraulic cement-based materials. MDF materials arising through reactions of sulfo-aluminate-ferrite belitic (SAFB) clinkers and/or Portland cements (PC) with two types of water-soluble polymer (hydroxy-propylmethyl cellulose {HPMC}, polyphosphate glass {poly-P}) are discussed. Mixes of low energy SAFB clinkers with Portland cement, HPMC and, especially poly-P comprise promising cross-linked compositions additional to the better known MDF materials formed from high alumina cement with polyvinylalcohol/acetate. The principles of co-ordination of P and C atoms (of the polymer) with Al and Fe atoms (originating from the cement) are highlighted from spectroscopic information on next-nearest-neighbour interactions, along with the effects of second co-ordination spheres. Polymers modify the interface through functional bonding/grafting of polymer chains onto the surfaces of cement grains. Both the cross-linked atomic structure and the interface coincide well with the model of functional polymers and represent a new type of atomic-level structure in polymer-modified cements. Interpretation is based on previous magnetic resonance and thermal analysis studies. The compactness of Al(Fe)-O-P cross-links reduces transport through the interfaces, increasing the interfacial interactions and resisting the unfavourable uptake of moisture and carbonation.     

基于分形维数的液体爆炸分散中界面破碎形态研究

通过对爆炸抛撒图象的处理,得到液体界面的曲线.采用盒维数的计算方式,计算界面曲线的分形维数.通过对各时刻液体界面分形维数的变化研究,分析爆炸抛撒近场阶段的变化过程,同时观察到蘑菇状尖顶的出现与破碎,以及空化区域的形成和消失现象。     

用AT89C51单片机和MAX505 DAC研制的程控信号源

本文介绍了用单片机AT89C51和MAX505 DAC制作程控信号源的原理,并在其中对AT89C51单片机和MAX505 DAC的工作原理及特性,怎样用单片机的中断控制和串行接口控制作为重点给予了阐述。     

Electrochemical Immunoanalysis for Carcinoembryonic Antigen Based on Multilayer Architectures of Gold Nanoparticles and Polycation Biomimetic Interface on Glassy Carbon Electrode

This paper describes a layer‐by‐layer (LBL) self‐assembly process of chitosan (CTS) and gold nanoparticles (Au) on the pretreated negatively charged glassy carbon (GC) electrode to fabricate electrochemistry immunosensor with a nontoxic biomimetic interface, which provided an environment similar to a native system and allowed more freedom in orientation for immobilization of carcinoembryonic antibody (anti‐CEA) to monitor carcinoembryonic antigen (CEA). UV‐vis spectroscope, atomic force microscopy (AFM), and cyclic voltammetric (CV) measurements were used to follow the multilayer film formation. The performance of the biominetic interface and factors influencing the assay system were investigated in detail. The differential pulse voltammetry (DPV) current response is used for the CEA concentration assay. The dynamic range was from 0.50 to 80.00 ng mL^?1 with a detection limit of 0.27 ng mL^?1 at 3σ. In addition, the experiment results indicate that immobilization described in this proposed method exhibits a good sensitivity, selectivity, and stability.