压力淬火过程中锗的相结构研究

 应用高压原位差热方法，直接测量了压力下锗的固化参数─—固化温度与过冷度。高压差热信号表明，当压力大于3 GPa时，锗在凝固过程中可能发生结构相变。X射线结构分析表明，在最终的样品中除GeⅠ相外，还形成GeⅢ相和GeⅣ相。     

二氧化钒薄膜的低温制备及其性能研究

针对VO₂薄膜在微测辐射热计上的应用，采用射频反应溅射法，在室温下制备氧化钒薄膜；研究了氧分压对薄膜沉积速率、电学性质及成分的影响.通过调节氧分压，先获得成分接近VO₂的非晶化薄膜，再在400℃空气中氧化退火，便可制得高电阻温度系数，低电阻率的VO₂薄膜，电阻温度系数约为-4%/℃，薄膜方块电阻为R_□为100—300kΩ；薄膜在室温下沉积，400℃下退火的制备方法与微机电加工(micro electromechanic 关键词： 二氧化钒 电阻温度系数 氧分压 射频反应溅射法     

数字散斑相关方法及其在碳纤维复合材料压力容器变形测量中的应用

提出了一种新的基于图像灰度梯度迭代的数字散斑相关方法(DSCM,digital speckle correlation method)。通过使用DSCM测量碳纤维复合材料压力容器在水压下的局部区域的位移场和应变场,分析了复合材料压力容器的轴向和环向的变形特征,为碳纤维复合材料压力容器的优化设计提供了理论和实验依据。     

High index of refraction via quantum interference in a three-level system of Er^3＋-doped yttrium aluminium garnet crystal

A simple three-level system is proposed to produce high index of refraction with zero absorption in an Er^3＋-doped yttrium aluminium garnet （YAG） crystal, which is achieved for a probe field between the excited state 4I13/2 and ground state 4I15/2 by adjusting a strong coherent driving field between the upper excited state 4I11/2 and 4I15/2. It is found that the changes of the frequency of the coherent driving field and the concentration of Er^3＋ ions in the YAG crystal can maximize the index of refraction accompanied by vanishing absorption. This result could be useful for the dispersion compensation in fibre communication, laser particle acceleration, high precision magnetometry and so on.     

Nanostructured thermoset epoxy resin templated by an amphiphilic poly(ethylene oxide)‐block‐poly(dimethylsiloxane) diblock copolymer

An amphiphilic poly(ethylene oxide)‐block‐poly(dimethylsiloxane) (PEO–PDMS) diblock copolymer was used to template a bisphenol A type epoxy resin (ER); nanostructured thermoset blends of ER and PEO–PDMS were prepared with 4,4′‐methylenedianiline (MDA) as the curing agent. The phase behavior, crystallization, hydrogen‐bonding interactions, and nanoscale structures were investigated with differential scanning calorimetry, Fourier transform infrared spectroscopy, transmission electron microscopy, and small‐angle X‐ray scattering. The uncured ER was miscible with the poly(ethylene oxide) block of PEO–PDMS, and the uncured blends were not macroscopically phase‐separated. Macroscopic phase separation took place in the MDA‐cured ER/PEO–PDMS blends containing 60–80 wt % PEO–PDMS diblock copolymer. However, the composition‐dependent nanostructures were formed in the cured blends with 10–50 wt % PEO–PDMS, which did not show macroscopic phase separation. The poly(dimethylsiloxane) microdomains with sizes of 10–20 nm were dispersed in a continuous ER‐rich phase; the average distance between the neighboring microdomains was in the range of 20–50 nm. The miscibility between the cured ER and the poly(ethylene oxide) block of PEO–PDMS was ascribed to the favorable hydrogen‐bonding interaction. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3042–3052, 2006     

合肥光源高亮度模式Lattice设计

介绍了一组合肥光源新高亮度模式的Lattice. 新的设计维持了储存环上所有元件和光束线位置不变,也没有加入新的元件. 取得了较低发射度. 所有直线节处的垂直方向β函数值都很小，适合插入件的运行. 跟踪计算表明新Lattice具有足够大的动力学孔径用于注入和储存粒子.     

新疆玛纳斯湖水蒸发过程研究

本文依据Na^ ,K^ ,Mg^2 //Cl^-,SO4^2--H2O五元水盐体系相图，对新疆玛纳斯盐湖水进行原料分析、理论研究、25℃等温蒸发实验和自然蒸发实验，研究了该湖水蒸发过程中盐类的析出规律及湖水中各组分浓度变化的规律，为进行工艺实验及将来的综合开发利用提供了可靠依据。     

Numerical solutions of the shallow water equations with discontinuous bed topography

A simple scheme is developed for treatment of vertical bed topography in shallow water flows. The effect of the vertical step on flows is modelled with the shallow water equations including local energy loss terms. The bed elevation is denoted with z_b^‐ for the left and z_b⁺ for the right values at each grid point, hence exactly representing a discontinuity in the bed topography. The surface gradient method (SGM) is generalized to reconstruct water depths at cell interfaces involving a vertical step so that the fluxes at the cell interfaces can accurately be calculated with a Riemann solver. The scheme is verified by predicting a surge crossing a step, a tidal flow over a step and dam‐break flows on wet/dry beds. The results have shown good agreements compared with analytical solutions and available experimental data. The scheme is efficient, robust, and may be used for practical flow calculations. Copyright © 2002 John Wiley & Sons, Ltd.     

A comparative study of the structure and crystallization of bulk metallic amorphous rod Pr60Ni30Al10 and melt-spun metallic amorphous ribbon Al87Ni10Pr3

Pr-based bulk metallic amorphous （BMA） rods （Pr60Ni30Al10） and Al-based amorphous ribbons （Al87Ni10Pr3） have been prepared by using copper mould casting and single roller melt-spun techniques, respectively. Thermal parameters deduced from differential scanning calorimeter （DSC） indicate that the glass-forming ability （GFA） of Pr60Ni30Al10 BMA rod is far higher than that of Al87Ni10Pr3 ribbon. A comparative study about the differences in structure between the two kinds of glass-forming alloys, superheated viscosity and crystallization are also made. Compared with the amorphous alloy Al87Ni10Pr3, the BMA alloy Pr60Ni30Al10 shows high thermal stability and large viscosity, small diffusivity at the same superheated temperatures. The results of x-Ray diffraction （XRD） and transmission electron microscope （TEM） show the pronounced difference in structure between the two amorphous alloys. Together with crystallization results, the main structure compositions of the amorphous samples are confirmed. It seems that the higher the GFA, the more topological type clusters in the Pr-Ni-Al amorphous alloys, the GFAs of the present glass-forming alloys are closely related to their structures.