Thermal Resistance Measurement across a Wick Structure Using a Novel Thermosyphon Test Chamber

A novel system is developed for measuring the thermal resistance across thin layers of sintered copper wicks of varying porosity. Wicks to be tested are integrated into a passive vertical thermosyphon system, and the resistance is measured for a series of input power levels. The wicks are sintered to a thermally conducting pedestal above a pool of deionized water and heated from below. The apparent thermal resistance across the wick (from the pedestal/wick interface to the vapor space) under the evaporative operating conditions encountered in heat pipes is measured using thermocouples. The apparent thermal resistance across the wick is measured to be as low as 0.01°C/W, corresponding to an evaporative heat transfer coefficient of greater than 128,000 W/m²K.     

1,4-双(二苯基膦)丁烷交联的季膦化聚芳醚酮阴离子交换膜

以1,4-双(二苯基膦)丁烷为交联剂,以具有四甲基联苯结构的聚芳醚酮为基体材料,分别制备了刚性三苯基膦和柔性三丁基膦修饰的阴离子交联膜材料.交联剂在交联结构形成的过程中转变成季膦盐,在提高膜材料机械稳定性的同时保持离子交换功能基团的含量.研究了2种阴离子交换膜的尺寸稳定性、电导率、机械性能及耐碱稳定性等.研究结果表明,当交联度为20%时,三苯基膦与三丁基膦修饰的阴离子交换膜的拉伸强度分别由未交联时的27和18 MPa提高到45和30 MPa;交联的膜材料在60℃的3 mol/L KOH溶液中浸泡120 h后,三苯基膦修饰的阴离子交换膜的电导率保留率为81%,三丁基膦修饰的阴离子交换膜的电导率保留率为69%,膜的耐碱稳定性均较未交联时有明显提高.交联度相同时,三苯基膦修饰的阴离子交换膜表现出更高的拉伸强度和更好的耐碱稳定性.     

Thermal degradation and fire performance of intumescent silicone‐based coatings

This paper deals with the thermal degradation and fire performance of silicone‐based coatings for protecting steel. In this study, the fire performance of silicone coatings as virgin or formulated materials is evaluated using two homemade fire testing methodologies: one similar to the “torch test” fire testing method and the other using a heat radiator test. It was shown that the performance of the silicone‐based coating used as thermal barrier can be improved incorporating a modifier (a mixture of polydimethylsiloxane and silica coated by a silane). In this case, silicone‐based coating swells and exhibits same fire performance as commercial intumescent coating at the torch test. It is shown that the incorporation of modifier in the silicone makes it to swell upon heating resulting in the formation of expanded material exhibiting low heat conductivity. Thermal degradation of the coating is also investigated: it occurs in three main steps leading to the formation of a tridimensional network characterized by the formation of Q⁴ structure at high temperature. Copyright © 2012 John Wiley & Sons, Ltd.     

涡流发生器污垢特性实验台的设计

为了研究涡流发生器的污垢特性设计了一个能够在线监测温度、流量以及压差进而可以直接得到污垢热阻的实验台。通过验证实验、准确性分析与误差分析,验证了实验台设计精度在允许的误差范围内。示例实验结果表明实验台具有研究涡流发生器的污垢特性、压力特性以及换热特性的功能。     

Development and validation of a LC‐MS/MS method for quantitation of fosfomycin – Application to in vitro antimicrobial resistance study using hollow‐fiber infection model

Extensive use and misuse of antibiotics over the past 50 years has contributed to the emergence and spread of antibiotic‐resistant bacterial strains, rendering them as a global health concern. To address this issue, a dynamic in vitro hollow‐fiber system, which mimics the in vivo environment more closely than the static model, was used to study the emergence of bacterial resistance of Escherichia coli against fosfomycin (FOS). To aid in this endeavor we developed and validated a liquid chromatography–tandem mass spectrometry (LC‐MS/MS) assay for quantitative analysis of FOS in lysogeny broth. FOS was resolved on a Kinetex HILIC (2.1 × 50 mm, 2.6 μm) column with 2 mm ammonium acetate (pH 4.76) and acetonitrile as mobile phase within 3 min. Multiple reaction monitoring was used to acquire data on a triple quadrupole mass spectrometer. The assay was linear from 1 to 1000 μg/mL. Inter‐ and intra‐assay precision and accuracy were <15% and between ±85 and 115% respectively. No significant matrix effect was observed when corrected with the internal standard. FOS was stable for up to 24 h at room temperature, up to three freeze–thaw cycles and up to 24 h when stored at 4°C in the autosampler. In vitro experimental data were similar to the simulated plasma pharmacokinetic data, further confirming the appropriateness of the experimental design to quantitate antibiotics and study occurrence of antimicrobial resistance in real time. The validated LC‐MS/MS assays for quantitative determination of FOS in lysogeny broth will help antimicrobial drug resistance studies.     

Study of Temperature and UV Wavelength Range Effects on Degradation of Photo-Irradiated Polyethylene Films Using DMA

Plastic bags mostly made of polyethylene (PE) cause pollution as solid waste due to their non-degradability nature. Initiation of a degradative process by enhanced photo-oxidation is a possible method for an accelerated degradation. This paper presents temperature treatment effects on PE films where photodegradation was initiated using ultraviolet (UV) irradiation in the ranges of 200–300 nm and 300–400 nm for 2 hr. Effects of temperature of 40°C and 55°C on non-UV-irradiated and UV-irradiated PE films processed by conventional methods were investigated and evaluated after 50 hr, 150 hr, and 350 hr of temperature exposure. The effects of UV wavelength range irradiation on the degradation were deduced. Measuring the dynamic moduli using a dynamic mechanical analyzer monitored the degradation. The decrease in average storage modulus was 62% with treatment at 55°C, higher than the 16% drop at 40°C for unirradiated samples after 350-hr exposure. Cross-linking in UV-exposed samples, characterized by an increase in dynamic modulus (stiffening), was observed followed by a reduction of storage modulus. Temperature treatment at 55°C together with 300–400-nm UV range irradiation resulted in the largest increase, i.e., 22% after 150 hr, followed by the largest reduction of storage modulus, i.e., 74.6% for a cumulative 350-hr exposure.     

Multiple Keys for a Single Lock: The Unusual Structural Plasticity of the Nucleotidyltransferase (4′)/Kanamycin Complex

The most common mode of bacterial resistance to aminoglycoside antibiotics is the enzyme‐catalysed chemical modification of the drug. Over the last two decades, significant efforts in medicinal chemistry have been focused on the design of non‐ inactivable antibiotics. Unfortunately, this strategy has met with limited success on account of the remarkably wide substrate specificity of aminoglycoside‐modifying enzymes. To understand the mechanisms behind substrate promiscuity, we have performed a comprehensive experimental and theoretical analysis of the molecular‐recognition processes that lead to antibiotic inactivation by Staphylococcus aureus nucleotidyltransferase 4′(ANT(4′)), a clinically relevant protein. According to our results, the ability of this enzyme to inactivate structurally diverse polycationic molecules relies on three specific features of the catalytic region. First, the dominant role of electrostatics in aminoglycoside recognition, in combination with the significant extension of the enzyme anionic regions, confers to the protein/antibiotic complex a highly dynamic character. The motion deduced for the bound antibiotic seem to be essential for the enzyme action and probably provide a mechanism to explore alternative drug inactivation modes. Second, the nucleotide recognition is exclusively mediated by the inorganic fragment. In fact, even inorganic triphosphate can be employed as a substrate. Third, ANT(4′) seems to be equipped with a duplicated basic catalyst that is able to promote drug inactivation through different reactive geometries. This particular combination of features explains the enzyme versatility and renders the design of non‐inactivable derivatives a challenging task.     

A comparative study of fluorine substituents for enhanced stability of flexible and ITO‐free high‐performance polymer solar cells

Two low‐band gap polymer series based on benzo[1,2‐b:4,5‐b′]dithiophene (BDT) and dithienylbenzothiadiazole, with different numbers of fluorine substituents on the 2,3,1‐benzothiadiazole unit, have been synthesized and explored in a comparative study of the photochemical stability and operational lifetime in flexible large area roll‐coated bulk heterojunction solar cells. The two polymer series have different side chains on the BDT unit, namely 2‐hexyldecyloxy (BDT_HDO) ( P1–P3 ) or 2‐hexyldecylthiophene (BDT_THD) ( P4–P6 ). The photochemical stability clearly shows that the stability enhances along with the number of fluorine atoms incorporated on the polymer backbone. Fabrication of the polymer solar cells based on the materials was carried out in ambient atmosphere on a roll coating/printing machine employing flexible and indium‐tin‐oxide‐free plastic substrates. Solar cells based on the P4–P6 series showed the best performance, reaching efficiencies up to 3.8% for an active area of 1 cm², due to an enhanced current compared to P1–P3 . Lifetime measurements, carried out according to international summit on OPV stability (ISOS), of encapsulated devices reveals an initial fast decay for P1–P6 in the performance followed by a much slower decay rate, still retaining 40–55% of their initial performance after 250 h of testing under ISOS‐L‐1 conditions. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 893–899