Influence of Some Aggressive Media on Corrosion Resistance of Mortars With Spent Cracking Catalyst

The influence of spent catalyst from catalytic cracking in fluidized bed on the hydration process of cement and the properties of cement mortars were studied. The spent catalyst was used as an additive to cement in the mortars (10 and 20% of cement). The samples of mortars kept in water for28 days, then they were placed in sulfate and chloride media for 2 months (the control samples were kept in water for 3 months). After this time they were subjected to bending strength and compressive strength determinations. Thermogravimetric and infrared absorption studies were performed and capillary elevation, capability of binding heavy metals, and changes in mass and apparent density were determined too. The studies disclosed the pozzolana nature of spent catalyst and its influence on cement mortars being in contact with corrosive media. This revised version was published online in August 2006 with corrections to the Cover Date.     

主动冷却点阵夹层防热结构温度响应计算模型北大核心CSCD

针对点阵夹层结构主动热防护问题,建立了夹层结构面板和芯体导热与冷却剂对流耦合的非稳态传热理论模型,利用有限体积法离散控制方程并在MATLAB中进行了迭代求解.模型首次考虑了面板与夹芯杆之间的收缩热阻,并利用分离变量法得到了收缩热阻的近似解析解.基于单胞模型和周期性边界条件,模拟得到了模型所需的表面对流传热系数h_(b)和h_(fin).最后,选取多单胞计算工况进行数值模拟和理论模型对比,并讨论了收缩热阻对模型预测精度的影响.结果表明:理论模型能够准确预测夹层结构及内部流体的温度变化,理论与仿真之间的最大误差不超过1%;随着外加热流密度不断增大,忽略收缩热阻使得计算结果造成的误差不断增大;与数值模拟相比,理论模型可显著地减少计算时间并节省计算资源,尤其适用于非均匀、非稳态复杂热载荷下点阵夹层结构的温度响应计算.     

Normalized Dynamic Characterization and Application of Multiple Heat Storage Materials Based on Standard Thermal Resistance北大核心CSCD

基于标准热阻和能量流法,推导出储热材料与换热流体的瞬态换热热阻,通过类比电路分析法,获得了储热-换热过程的瞬态热量流模型及动态响应时间常数。进一步引入节点温度,重新定义换热热阻,获得了储热与换热过程耦合的三阶电路瞬态热量流模型,求解得到了加热、储热和释热三类时间常数,可用于协同表征储热材料中储热与释热的快慢程度,从而实现了多类储热材料的归一化动态表征。通过数值模拟验证与应用对比分析,发现基于多时间常数的归一化动态模型用于表征储热材料的动态特性是可行的,可直接对不同换热、储热材料进行对比分析。案例分析发现与固体储热材料换热时,液态金属的动态换热能力优于熔融盐,而相比于水蒸气和CO₂,空气与陶瓷材料换热能更快达到稳态。     

钇提高YT14硬质合金耐磨性的机制

研究了不同Ｙ添加量对ＹＴ１４硬质合金显微组织、结构和耐磨性的影响。结果表明，在ＹＴ１４硬质合金中添加微量Ｙ，可显著提高合金的耐磨性。Ｙ的主要作用是均匀细化碳化物相和Ｃｏ相；提高Ｃｏ粘结相中Ｗ、Ｔｉ元素的固溶量及αＣｏ相所占的体积分数，从而提高Ｃｏ粘结相的强韧性；Ｙ在合金中形成Ｙ２ＷＯ６，表明Ｙ还可还原和清除碳化钨表面氧化膜，增强Ｃｏ粘结相与硬质相之间的结合强度     

Analysis of promazines in bovine livers by high performance liquid chromatography with ultraviolet and fluorimetric detection

Fluorimetric and UV methods of detection for liquid chromatographic determination of phenothiazines (chlorpromazine, acetopromazine and propionylpromazine) were developed. The effects of several experimental parameters on the separation and the sensitivity of the methods were evaluated. The detection limits ranged from 31 to 350 ng ml⁻¹. Optimized methods were successfully applied to determination of the promazines in bovine liver samples.     

Amino acid overproduction by analog resistant mutants of the nitrogen fixing cyanobacteriumAnabaena sp 287

Two amino acid analog resistant mutants of the cyanobacteriumAnabaena sp 287 were isolated after MNNG mutagenesis.Anabaena ST 16, a mutant resistant to the alanine analog D-α-aminobutyric acid andAnabaena ST 25, another mutant resistant to the histidine analog l,2,4-triazole-3-alanine, released alanine and histidine, respectively, into the medium upon immobilization in alginic acid during diazotrophic growth in fluidized bed reactors. The rates of amino acid production by the mutants were 4.3 μmol mg chl^-1 h^-1 of D-alanine byAnabaena ST 16 and 16.6 μnol mg chl^-1 h^-1 of L-histidine byAnabaena ST 25. Nitrogen fixation by the mutants was not affected by the extracellular amino acid concentration. While the radioactive carbon flow was followed, the parent strain retained 93% of fixed¹⁴C and released only 7% into the medium. On the other hand,Anabaena ST 16 released 13% andAnabaena ST 25 released 29% into the medium. These mutants are beneficial in the production of radioactive amino acids using diazotrophic photobiotechnology.     

A common method for the determination of several calcium channel blockers using an HPLC system with ultraviolet detection

We report a common HPLC method for the single or simultaneous determination of four calcium channel blockers (CCB), namely diltiazem (DTZ), verapamil (VER), nifedipine (NIF) and nitrendipine (NIT) and their active metabolites demetildiltiazem and deacetildiltiazem (MA and M1), norverapamil (NOR), and dehydronifedipine (DHN). DHN was first synthesised in our laboratory and different pH values of the mobil phase were subsequently prepared and tested for chromatographic separation. The detection system and the environmental light conditions were optimised. The best separations of all analytes were obtained using a C₁₈ column and a mobile phase of methanol, 0.04 M ammonium acetate, acetonitrile and triethylamine (2:2:1:0.04 v/v). Quantitation was performed using imipramine (IMI) as the internal standard. For DTZ and its metabolites (M1 and MA), the wavelength chosen was 237 nm; for VER and its metabolite NOR, it was 210 nm; and, finally for NIF and its metabolite DHN and NIT it was 216 nm. When a simultaneous analysis was carried out the wavelength was of 230 nm. The optimum pH were 7.90 and 7.10 when the separation of NIT and DTZ or VER and NIF were carried out, respectively, and 7.90 when a simultaneous separation was carried out. The detection limit of the assay was less than 8 ng ml⁻¹ for all compounds, with coefficients of variation less than 7% (for inter- and intra-day) over the concentration range of 1–1000 ng ml⁻¹. The retention times were less than 11 min. When NIF or NIT were studied, it was necessary to use a sodium vapour lamp in order to avoid the photodegradation which takes place under daylight conditions.     

Assessment of corrosion resistance of surface-coated galvanized steel by analysis of the AC impedance spectra measured on the salt-spray-tested specimen

In the present work, corrosion resistance of surface-coated galvanized steel was quantitatively determined by an analysis of the alternating current (AC) impedance spectra measured on the salt-spray-tested specimen. To evaluate the corrosion resistance of the surface-coated galvanized steel, AC impedance spectroscopy was performed on the salt-spray-tested specimen previously exposed to salt-sprayed corrosive environment. From the analysis of the impedance spectra, the area fraction transient of white rust θ ₂(t) was theoretically derived from the equivalent circuit equation by using two fitting parameters. The values of the two fitting parameters were determined by fitting the empirical transient equations to the area fraction of the resin coating layer and to the total resistance obtained from the impedance spectra measured, respectively. From the analyses of θ ₂(t) for four kinds of surface-coated galvanized steels with various resin coating layers, it is indicated that as the values of the two fitting parameters decrease in the order of CP, GI, OD and OM (commercial trade names) specimens, the corrosion resistance increases in that order as well. Furthermore, from the quantitative comparison of the two fitting parameters with the polarization resistance of the upper resin coating layer R _p determined from the potentiodynamic polarization curve, it is suggested that the two fitting parameters decrease in value as well with increasing R _p.     

Photoinduced graft polymerization of 2-methacryloyloxyethyl phosphorylcholine on polyethylene membrane surface for obtaining blood cell adhesion resistance

Phospholipid polymer, poly[2-methacryloyloxyethyl phosphorylcholine (MPC)], was grafted with polyethylene (PE) membrane using photoinduced polymerization technique to make the membrane resistant to cell adhesion. The water contact angle on the PE membrane grafted with poly(MPC) decreased with an increase in the photopolymerization time. This decrease corresponded to the increase in the amount of poly(MPC) grafted on the PE surface. The same graft polymerization procedure was applied using other hydrophilic monomers, such as acrylamide (AAm), N-vinylpyrrolidone (VPy) and methacryloyl poly(ethylene glycol) (MPEG). These monomers were also polymerized to form grafted chains on the PE membrane, and the grafting was confirmed with X-ray photoelectron spectroscopy. Analysis of amount and distribution of plasma proteins at the plasma-contacting surface of the original and the modified PE membranes were analyzed using immunogold assay. The grafting of poly(MPC) and poly(VPy) on PE membrane reduced the plasma protein adsorption significantly compared with that on the original PE membrane. However, the PE membranes grafted with poly(AAm) or poly(MPEG) did not show any effects on protein adsorption. Platelet adhesion on the original and modified PE membranes from platelet-rich plasma was also examined. A large number of platelets adhered and activated on the original PE membrane. Grafting with poly(AAm) did not suppress platelet adhesion, but grafting with poly(MPC) or poly(VPy) on the PE membrane was effective in preventing platelet adhesion. It is concluded that the introduction of the phosphorylcholine group on the surface could decrease the cell adhesion to substrate polymer.     

Novel method for bulk resistance evaluation in conductivity measurement for high-purity water

A major issue with the electrolytic conductivity measurement for pure water is the lack of standard or reference methods. A primary method traceable to SI and suitable for pure-water conductivity measurement was developed at the Physikalisch-Technische Bundesanstalt (PTB), Germany, as the base for the calibration method for the conductivity measuring devices at the low conductivity level. This paper provides a novel method to calculate the bulk resistance of pure water using impedance measured at a single frequency, which is one of the key procedures for the primary methods.