Biofouling-resistance expanded poly(tetrafluoroethylene) membrane with a hydrogel-like layer of surface-immobilized poly(ethylene glycol) methacrylate for human plasma protein repulsions

In general, it is a challenge to control the highly polar material grafting from the chemically inert Teflon-based membrane surface. This work describes the surface modification and characterization of expanded poly(tetrafluoroethylene) (ePTFE) membranes grafted with poly(ethylene glycol) methacrylate (PEGMA) macromonomer via surface-activated plasma treatment and thermally induced graft copolymerization. The chemical composition and microstructure of the surface-modified ePTFE membranes were characterized by Fourier transform infrared spectroscopy (FT-IR), contact angle, and bio-atomic force microscopy (bio-AFM) measurements. Biofouling property of the modified membranes was evaluated by the measurements of the plasma protein (γ-globulin, fibrinogen, or albumin) adsorption determined using an enzyme-linked immunosorbent assay (ELISA). In general, the hydrophilicity of the surface of ePTFE membranes increases with increasing the grafting degree of the copolymerized PEGMA. The highly hydrated PEGMA chain on the resulting ePTFE membranes was found to form a surface hydrogel-like layer with regulated coverage in aqueous state, which can be controlled by the content of PEGMA macromonomer in the reaction solution. The relative protein adsorption was effectively reduced with increasing capacity of the hydration for the PEGMA chain grafted on the ePTFE membrane surface. From both results of protein adsorption and platelet adhesion test in vitro, it is concluded that the PEGMA-grafted hydrophilic ePTFE membranes could provide good biofouling resistance to substantially reduce plasma protein and blood platelet fouling on the membrane surface in human body temperature.     

Atom‐transfer radical grafting polymerization of 2‐methacryloyloxyethyl phosphorylcholine from silicon wafer surfaces

2‐Methacryloyloxyethyl phosphorylcholine (MPC), a biomimetic monomer, was grafted from silicon wafer surfaces at room temperature by combining self‐assembly of initiator and surface‐initiated atom transfer radical polymerization. Two methods were used to control the grafting process. One was to add free initiator to the reaction system; the other was to add excess deactivator. The grafting densities up to 0.3 chains/nm² were obtained. The surface thickness increased linearly with MPC conversion. The thickness depended on catalyst and monomer concentrations, as well as activator/deactivator ratio. Poly(MPC) layers of >100 nm thick were obtained by optimizing the polymerization conditions. A second block of either poly(MPC) or poly[2‐(dimethylamino)ethyl methacrylate] was also grown from the grafted poly(MPC), demonstrating the system livingness. X‐ray photoelectron spectroscopy was used to examine the surface chemical compositions showed good agreement with the theoretical values. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2931–2942, 2004     

Covalent attachment of phospholipid analogous polymers to modify a polymeric membrane surface: a novel approach

A novel method for the surface modification of a microporous polypropylene membrane by tethering phospholipid analogous polymers (PAPs) is given, which includes the photoinduced graft polymerization of N,N-dimethylaminoethyl methacrylate (DMAEMA) and the ring-opening reaction of grafted poly-(DMAEMA) with 2-alkyloxy-2-oxo-1,3,2-dioxaphospholanes. Five 2-alkyloxy-2-oxo-1,3,2-dioxaphospholanes, containing octyloxy, dodecyloxy, tetradecyloxy, hexadecyloxy, and octadecyloxy groups in the molecular structure, were used to fabricate the PAP-modified polypropylene membranes. The attenuated total reflectance FT-IR spectra of the original, poly(DMAEMA)-grafted, and PAP-modified membranes confirmed the chemical changes on the membrane surface. Scanning electron microscope pictures showed that, compared with the original membrane, the surface porosities ofpoly(DMAEMA)-grafted and PAP-modified membranes were somewhat reduced. Water contact angles measured by the sessile drop method on PAP-modified membranes were slightly lower than that on the original polypropylene membrane, but higher than those on poly(DMAEMA)-grafted membranes with the exception of octyloxy-containing PAP-modified membranes. However, BSA adsorption experiments indicated that the five PAP-modified membranes had a much better protein-resistant property than the original polypropylene membrane and the poly(DMAEMA)-grafted membranes. For hexadecyloxy- and octadecyloxy-containing PAP-modified membranes, almost no protein adsorption was observed when the grafting degree was above 6 wt %. It was also found that the platelet adhesion was remarkably suppressed on the PAP-modified membranes. All these results demonstrate that the described approach is an effective way to improve the surface biocompatibility for polymeric membranes.     

Hemocompatibility of poly(vinylidene fluoride) membrane grafted with network-like and brush-like antifouling layer controlled via plasma-induced surface PEGylation

In this work, the hemocompatibility of PEGylated poly(vinylidene fluoride) (PVDF) microporous membranes with varying grafting coverage and structures via plasma-induced surface PEGylation was studied. Network-like and brush-like PEGylated layers on PVDF membrane surfaces were achieved by low-pressure and atmospheric plasma treatment. The chemical composition, physical morphology, grafting structure, surface hydrophilicity, and hydration capability of prepared membranes were determined to illustrate the correlations between grafting qualities and hemocompatibility of PEGylated PVDF membranes in contact with human blood. Plasma protein adsorption onto different PEGylated PVDF membranes from single-protein solutions and the complex medium of 100% human plasma were measured by enzyme-linked immunosorbent assay (ELISA) with monoclonal antibodies. Hemocompatibility of the PEGylated membranes was evaluated by the antifouling property of platelet adhesion observed by scanning electron microscopy (SEM) and the anticoagulant activity of the blood coagulant determined by testing plasma-clotting time. The control of grafting structures of PEGylated layers highly regulates the PVDF membrane to resist the adsorption of plasma proteins, the adhesion of platelets, and the coagulation of human plasma. It was found that PVDF membranes grafted with brush-like PEGylated layers presented higher hydration capability with binding water molecules than with network-like PEGylated layers to improve the hemocompatible character of plasma protein and blood platelet resistance in human blood. This work suggests that the hemocompatible nature of grafted PEGylated polymers by controlling grafting structures gives them great potential in the molecular design of antithrombogenic membranes for use in human blood.     

Photoinduced phospholipid polymer grafting on Parylene film: advanced lubrication and antibiofouling properties

Poly(p-xylylene) (Parylene C) coatings have been applied in implantable electronic devices because of their electrical insulation and moisture barrier properties. To provide lubrication and an antibiofouling surface, a biomimetic phospholipid polymer--poly(2-methacryloyloxyethyl phosphorylcholine (MPC))--was grafted from the surface using UV irradiation with benzophenone as an initiator. The poly(MPC) grafting on the Parylene C films was confirmed by attenuated total reflection-Fourier transfer inflated irradiation, X-ray photoelectron spectroscopy and ellipsometry. These analyses indicated that the Parylene C films were completely covered by the poly(MPC)-graft layer with an average thickness of 140 nm under dry condition. The atomic force microscope (AFM) images revealed that the poly(MPC)-graft chains extended under wet condition. However, they formed globular structures under dry condition. Water contact angle measurements revealed a decreased receding angle of 29.5 degrees on the poly(MPC)-grafted surface with a high hysteresis of 41.4 degrees. These results indicate that the poly(MPC)-graft chains gain mobility in a wet environment. The average kinetic friction coefficient of the poly(MPC)-grafted surface in water was 0.018, which was 90% lower than that of the original surface. The in vitro single protein adsorption reduced by over 70% due to the poly(MPC) grafting. The hydrated poly(MPC)-graft chains are considered to provide lubrication and antibiofouling properties. The surface zeta potential measurement clarified the electroneutrality of the poly(MPC)-grafted surface. We concluded that the poly(MPC) grafting from the Parylene C layer significantly improved its surface properties and, subsequently, its biological properties.     

Surface structures of fluoropolymer,polyolefin and polyester films after modification by graft polymerization

Pristine and argon plasma pretreated polytetrafluoroethylene (PTFE), polystyrene (PS), high-density polyethylene (HDPE) and poly(ethylene terrephthalate) (PET) films have been subjected to near-UV light-induced graft polymerization with water-soluble acrylamide (AAm), the sodium salt of styrene sulfonic acid (NaSS), acrylic acid (AAc) and N,N-dimethylaminoethylmethylacrylate (DMAEMA) monomers. The structure and composition at the substrate surface with grafted polymer were studied by angle-resolved X-ray photoelectron spectroscopy (XPS). In most cases, the density of surface grafting is enhanced by plasma pretreatment. For each polymer substrate with a substantial amount of grafting, the hydrophilic graft penetrates or becomes partially submerged beneath a thin surface layer of dense substrate chains. This stratified microstructure is consistent with the static secondary ion mass spectroscopy (SIMS) and Ar⁺ beam depth profiling results. The two latter techniques also suggest that when the grafted polymer has a bulky substituent, there is less efficient penetration of the grafted polymer below the surface.     

Improving hydrophilicity and protein antifouling of electrospun poly(vinylidenefluoride-hexafluoropropylene) nanofiber membranes

<正>Poly(vinylidenefluoride-hexafluoropropylene)(PVDF-HFP) nanofiber membranes with improved hydrophilicity and protein fouling resistance via surface graft copolymerization of hydrophilic monomers were prepared.The surface modification involves atmospheric pressure glow discharge plasma(APGDP) pretreatment followed by graft copolymerization of poly(ethylene glycol) methyl ether methacrylate(PEGMA).The success of the graft modification with PEGMA on the PVDF-HFP fibrous membrane is ascertained by X-ray photoelectron spectroscopy(XPS) and attenuated total reflectance Fourier transform infrared measurements(ATR-FTIR).The hydrophilic property of the nanofiber membranes is assessed by water contact angle measurements.The results show that the PEGMA grafted PVDF-HFP nanofiber membrane has a water contact angle of 0°compared with the pristine value of 132°.The protein adsorption was effectively reduced after PEGMA grafting on the PVDF-HFP nanofiber membrane surface.The PEGMA polymer grafting density on the PVDF-HFP membrane surface is measured by the gravimetric method,and the filtration performance is characterized by the measurement of water flux.The results indicate that the water flux of the grafted PVDF-HFP fibrous membrane increases significantly with the increase of the PEGMA grafting density.     

Preparation and properties of biocompatible polymer-grafted silica nanoparticle

Grafting of biocompatible polymer onto the surface of silica nanoparticles was achieved by radical graft polymerization of 2-methacryloyloxyethyl phosphorylcholine (MPC), initiated by azo groups previously introduced onto the surface or by a system consisting of Mo(CO)₆ and trichloroacetyl groups on the silica surface. Both of these systems have the ability to initiate graft polymerization of MPC, resulting in the formation of poly(MPC)-grafted silica, but the percentage of poly(MPC) grafting for the latter initiating system was much higher than that of the former. The amount of moisture that could be adsorbed onto the silica surface was found to increase with increasing poly(MPC) grafting. This indicates that grafting of poly(MPC) onto the silica surface markedly increases the hydrophilic nature of the surface. The contact angle of water in composites prepared from poly(vinyl alcohol) and poly(MPC)-grafted silica was found to decrease with increasing poly(MPC)-grafted silica content. When poly(MPC)-grafted silica was added to water containing a small amount of chloroform, it was found to act as stabilizer for droplets of chloroform. In addition, according to tests by the Lee-White method, poly(MPC)-grafted silica shows non-thrombogenic characteristics.     

Poly(N-isopropylacrylamide)-grafted dual stimuli-responsive filter paper for protein separation

Thermal and salt dual stimuli-responsive filter-paper-based membranes were prepared by UV-induced grafting of NIPAM-based polymers on paper surface. The grafting ratio could be controlled by monomer concentration during grafting polymerization. The results from pressure drop measurement of the mobile phase flowed cross the membrane demonstrate that an appropriate grafting ratio would be 8%-10%. Protein adsorption on the membrane through hydrophobic interaction could be promoted by increasing temperature and lyotropic salt concentration. The effect of grafted polymer structure on protein binding performance was studied. Filter paper grafted with NIPAM-based branched copolymer consisting of hydrophobic monomer moieties shows ten times higher protein binding capacity than that of the original filter paper. The separation of plasma proteins using the dual stimuli-responsive membrane was examined to demonstrate feasible application for hydrophobic interaction chromatographic separation of proteins.     

Structure and Surface Properties of High-density Polyelectrolyte Brushes at the Interface of Aqueous Solution

Zwitterionic and cationic polyelectrolyte brushes were prepared by surface-initiated atom transfer radical polymerization of 2-methacryloyloxy- ethyl phosphorylcholine (MPC) and 2-(N,N-dimethylamino)ethyl methacrylate (DMAEMA), respectively. The poly(DMAEMA) brush was treated with methyl iodide to form poly[2-(methacryloyloxy) ethyltrimethylammonium iodide] [poly(METAI)]. The effects of ionic strength on brush structure and surface properties of densely grafted polyelectrolyte brushes were analyzed by contact angle measurements, neutron reflectivity (NR) and macroscopic friction tests. Both polyelectrolyte brushes exhibited hydrophilic properties. The contact angle of the poly(MPC) brush surface against water was ca. 0° in air and the contact angle of the air bubble in water was ca. 170°. The air bubble in water hardly attached to the poly(MPC) brush surface, indicating super hydrophilic characteristics. NR measurements of poly(MPC) and poly(METAI) brushes showed that the grafted polymer chains were extended from the substrate surface in a good solvent such as water. Interestingly, NR study did not reveal the shrinkage of the brush chain in salt solution. The polyelectrolyte brushes immersed in both water and NaCl solution at various concentrations showed a low friction coefficient and low adhesion force.     

MMA/MPC共聚物膜的制备及其抗凝血性能研究

采用自由基共聚制得了甲基丙烯酸甲酯与2-甲基丙烯酰氧基乙基磷酰胆碱(MPC)的共聚物, 在模板中将溶剂蒸发得到了共聚物膜. 用差示扫描量热仪(DSC)、凝胶渗透色谱(GPC)、元素分析仪(EA)、氢核磁共振(¹H NMR)及扫描电子显微镜(SEM)对共聚物及其膜的结构与形态进行了表征, 并测定了膜的溶胀度与表面的亲水性, 结合对牛血清蛋白(BSA)吸附研究结果表明: 共聚物膜的溶胀度随着MPC含量的增加而逐渐上升, 并且随着温度的升高而逐渐增大; 由动态接触角(DCA)结果可知共聚物膜表面的链段可随着环境的变化而发生重排, MPC链段向膜表面的迁移提高了膜表面的亲水性, 降低了对蛋白质的吸附. 并通过体外血小板粘附试验对膜材料的抗凝血性能进行了评价. 结果表明, 当共聚物膜中w(MPC)＝0.25时, 膜表面吸附的血小板数量明显减少, 共聚物膜表现出良好的抗凝血性能.     

In-vitro hemocompatibility evaluation of a thermoplastic polyurethane membrane with surface-immobilized water-soluble chitosan and heparin

The surface of a thermoplastic polyurethane (TPU) membrane was treated with low temperature plasma (LTP) and was then grafted with poly(acrylic acid) (PAA), followed by the grafting of water-soluble chitosan (WSC) and heparin (HEP). The surface was characterized with static contact-angle and X-ray photoelectron spectroscopy (XPS). The results showed that the surface densities of peroxides and PAA reached a maximum when treated with LTP for 90 s. A higher pH of the reacting solution led to higher graft densities of WSC and HEP. After WSC and HEP grafting, the hydrophilicity of the TPU membrane was increased. The adsorption of proteins on HEP-grafted TPU membranes was effectively curtailed. In addition, HEP grafting also reduced platelet adhesion, elevated thrombin inactivation, and prolonged the blood coagulation time. According to the L929 fibroblast cell growth inhibition index, the HEP-grafted TPU membranes exhibited non-cytotoxicity. Overall results demonstrated that the HEP immobilization could not only improve the hydrophilicity but also the hemocompatibility of the TPU membrane, while maintaining the ascendant biocompatibility.     

Graft Polymerization of Vinyl Monomers Onto Carbon Black by Use of the Redox System Consisting of Ceric Ions and Carbon Black Carrying Alcoholic Hydroxyl Groups

The radical graft polymerization of vinyl monomers onto carbon black initiated by a redox system consisting of ceric ion and carbon black having alcoholic hydroxyl groups was investigated. The introduction of alcoholic hydroxyl groups onto the carbon black surface was achieved by the reaction of carbon black with alcoholic hydroxyl radicals, formed by the reaction of alcohol with benzoyl peroxide. The rate of the polymerization of acrylamide (AAm) initiated by the redox system was found to increase in the following order of hydroxyl groups: 1-hydroxyoctyl < 1-hydroxypropyl < 1-hydroxyethyl < hydroxymethyl < 1-hydroxy-1-methylethyl. In the redox polymerization, poly-AAm was effectively grafted onto carbon black by propagation of the polymer from the radical formed by the reaction of ceric ions with the alcoholic hydroxy groups. The percentage of grafting increased with increasing conversion. By use of this redox system, poly(acrylic acid), polyacrylonitrile, and poly(N-vinyl-2-pyrrolidone) could be grafted onto carbon black, but poly(methyl methacrylate) and polystyrene could not be so grafted. The graft polymerization of AAm by use of a redox system consisting of ceric ion and PVA-grafted carbon black was also investigated.     

Surface modification of polyethylene fiber by graft polymerization

To improve the wettability and adhesion, graft polymerization of acrylamide (AAm) and glycidyl methacrylate (GMA) was performed onto the surface of ultra-high modulus polyethylene (UHMPE) fiber pretreated with Ar plasma. Following the plasma treatment and the subsequent exposure to air to introduce peroxides onto the fiber surface, graft polymerization onto the UHMPE fiber was allowed to proceed from the polymer peroxides either in deaerated monomer solution at an elevated temperature (degassing method), or in aerated monomer solution containing riboflavin at 30°C under UV irradiation (photoinduction method). The monomer solution was prepared from water and dioxane for AAm and GMA, respectively. After rigorous removal of homopolymers, surface analysis of the grafted fibers was performed with ATR-FTIR and XPS, which revealed that PAAm and PGMA chains were grafted in the surface region of fibers. The grafting rate of PAAm by the photoinduction method was much higher than that by the degassing method when compared at the same concentration of the AAm solution. The amount of PGMA grafted was greatly affected by UV irradiation time, but depended on plasma treatment time to an insignificant extent if the treatment was carried out for longer than 30 s. Reaction of propylamine with the PGMA-grafted surface resulted in the appearance of a nitrogen peak in the XPS spectrum, suggesting the presence of epoxy groups on the surface of PGMA grafted fiber. © 1994 John Wiley & Sons, Inc.     

Surface modification of microporous polypropylene membranes by the grafting of poly(γ-stearyl-l-glutamate)

A polypeptide, poly(γ-stearyl-l-glutamate) (PSLG), was grafted on the surface of hydrophobic polypropylene hollow fiber membranes through the ring opening polymerization of N-carboxyanhydride (NCA) of γ-stearyl-l-glutamate initiated by amino groups which was generated by ammonia plasma. X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FT-IR), together with water contact angle and bovium serum albumin adsorption measurements were used to characterize the modified membrane surface. The XPS and FT-IR spectra demonstrated that polypeptide was actually grafted on the membrane surface despite of the low degree of graft polymerization due to the hydroxyl groups on the membrane surface. To subject the ammonia plasma-treated membrane with γ-(aminopropyl)triethanoxysilane (γ-APS) which can react with hydroxyl groups and leave amino groups, the degree of graft polymerization could be improved. The bovium serum albumin adsorption measurement was conducted to further examine the surface properties of modified and original membranes. Potential applications of the PSLG grafted membranes are expected for enantiomer separation and/or enzyme immobilization.     

Preparation of pH- and thermo-sensitive hydrogel by two-step grafting of acrylamide and acrylic acid onto preirradiated polyethylene film

Two-step grafting reaction of acrylamide (AAm) and acrylic acid (AAc) onto preirradiated polyethylene (PE) film were performed. The effects of irradiation dose, reaction temperature and reaction time on the grafting yield were studied. The effect of reaction time of the first step grafting on the yield of the second step grafting was also evaluated. The original and the irradiated PE films were tested by Fourier transform infrared (FTIR) spectroscopy in the attenuated total reflectance mode (ATR). The AAm and AAc grafted PE film appeared thermo- and pH-sensitive which are similar to the interpenetrating polymer network hydrogel. This revised version was published online in July 2006 with corrections to the Cover Date.     

聚氧乙烯功能基复合修饰聚氨酯的合成及其血液相容性研究 (Ⅰ)──聚氨酯-接枝-十八烷基聚氧乙烯

通过十八烷基聚氧乙烯和环氧氯丙烷的封端反应制备了α-环氧基-ω-十八烷基聚氧乙烯大单体.并采用BF₃·Et₂O引发THF和大单体共聚合,得到了梳状的十八烷基聚氧乙烯接枝共聚醚.以该共聚醚为软段合成了十八烷基和聚氧乙烯复合修饰的聚氨酯(PEU-g-PEO-C₁₈).通过血小板粘附试验对材料的体外抗凝血性实验结果表明,采用具有选择性吸附白蛋白功能的十八烷基和PEO复合修饰聚氨酯,材料表面血小板粘附量明显减少.材料血液相容性的改善可能来源于疏水性的十八烷基和亲水性聚氧乙烯的协同作用.     

Synthesis and biocompatibility of phosphoryl polymer and relationship between biocompatibility and water structure

A series of copolymers, poly(methylmethacrylate-co-2-methacryloyloxyethyl phosphorylcholine), with various compositions of methyl methacrylate (MMA) and 2-methacryloyloxyethyl phosphorylcholine (MPC) were synthesized by radical copolymerization in a mixed solvent of ethanol and chloroform. The structures of the copolymers were confirmed by proton nuclear magnetic resonance and elemental analysis. The properties and morphologies of the copolymers were characterized by differential scanning calorimeter, scanning electron microscopy, and optical microscope. The adsorption of bovine serum albumin (BSA) and the adhesion of platelet on the surfaces of the copolymer membrane significantly decreased with increasing the MPC composition. The copolymers containing MPC above 18% showed excellent biocompatibility. Moreover, the relationship between the water structure and the biocompatibility was illustrated by changing quantity of the MPC in copolymers. The result showed that the amount of free water affected the platelet compatibility of the copolymer.     

Blood compatibility of thermoplastic polyurethane membrane immobilized with water-soluble chitosan/dextran sulfate

Water-soluble chitosan (WSC)/dextran sulfate (DS) was immobilized onto the surface of thermoplastic polyurethane (TPU) membrane after ozone-induced graft polymerization of poly(acrylic acid) (PAA). The surface was characterized with contact angle measurement and X-ray photoelectron spectroscopy (XPS). The adsorption of human plasma fibrinogen (HPF) followed the Langmuir adsorption isotherm. The results showed that the surface density of peroxides generated and poly(acrylic acid) (PAA) grafted reached the maximum value at 20 min of ozone treatment. It was found that the WSC- and DS-immobilized amount increased with pH and the molecular weight of WSC. The membrane/water interfacial free energy increased with PAA-grafting and WSC/DS-immobilization, indicating the increasing wettability of TPU membrane. The adsorption of HPF on TPU-WSC/DS membranes could be effectively curtailed and exhibited unfavorable adsorption. Moreover, WSC/DS immobilization could effectively reduce platelet adhesion and prolong the blood coagulation time, thereby membrane improving blood compatibility of TPU membrane. In addition, the in vitro cytotoxicity test of PEC modification was non-cytotoxic according to much low growth inhibition of L929 fibroblasts. Furthermore, TPU-WSC/DS membranes exhibited higher cell viability than native TPU membrane.     

Improving the hydrophilic and antifouling properties of poly(vinyl chloride) membranes by atom transfer radical polymerization grafting of poly(ionic liquid) brushes

In this study, poly(1‐butyl‐3‐vinylimidazolium bromide) (PBVIm‐Br) was grafted onto the poly(vinyl chloride) (PVC) membrane surface via a 2‐step atom transfer radical polymerization (ATRP) reaction. Poly(2‐hydroxyethylmethacrylate) (PHEMA) was grafted onto the membrane surface by aqueous ATRP reaction; then, BVIm‐Br was introduced onto the surface of the PHEMA‐modified PVC membrane through traditional ATRP reaction. The analysis of surface chemistry confirmed the successful grafting of PHEMA and PBVIm‐Br on PVC membrane surface, and the grafting density (GD) of PBVIm‐Br gradually increased as the grafting time was prolonged. The modified membrane exhibited a positive charge and significantly enhanced surface hydrophilicity. The static water contact angle of the membrane surface decreased from 92.3° to 51.6° as the GD of the PBVIm‐Br brushes increased. Filtration experiments indicated that the water flux of the modified membrane increased with increasing GD, and their recovered fluxes were more than twice than the original. In addition, the total fouling ratio of the membranes decreased from 89% in M0 to 67% in M5, and most of the fouling was reversible as the GD of PBVIm‐Br brushes increased. These results indicated that the positive charged poly(ionic liquid) brushes featuring hydrophilic properties would have potential applications in membrane separation.