Uniformity in Computable Structure Theory

We investigate the effects of adding uniformity requirements to concepts in computable structure theory such as computable categoricity (of a structure) and intrinsic computability (of a relation on a computable structure). We consider and compare two different notions of uniformity, previously studied by Kudinov and by Ventsov. We discuss some of their results and establish new ones, while also exploring the connections with the relative computable structure theory of Ash, Knight, Manasse, and Slaman and Chisholm and with previous work of Ash, Knight, and Slaman on uniformity in a general computable structure-theoretical setting.     

Impedance and dielectric studies of ferroelectric SrBi2Nb2O9 ceramics

This paper reports the dielectric and impedance characteristics of ferroelectric SrBi₂Nb₂O₉ (SBN) ceramics in the 100 Hz-1 MHz frequency range at various temperatures (300-823 K). A strong low frequency dielectric dispersion (LFDD) associated with an impedance relaxation has been found to exist in these ceramics in the temperature range 573-823 K. The Z″ of the AC complex impedance showed two distinct slopes in the frequency range 100 Hz-1 MHz suggesting the existence of two dispersion mechanisms. This non-ideal behavior has been explained on the basis of the expression, Z*=R₀/(1+(iω/ω₁)^m+(iω/ω₂)ⁿ) [J. Phys. Chem. Solids 53 (1992) 1] where ω₁ and ω₂ characterize the lattice response and the charge carrier behavior, respectively. The exponents m and n were obtained from the curve fitting. The exponent n was found to exhibit a minimum at the Curie temperature, T_c (723 K) whereas the m was temperature independent.     

Mechanical Properties of Blends of Low-Density Polyethylene with Chlorinated Polyethylene

The results of experimental investigation into the mechanical properties of blends of low-density polyethylene (LDPE) with chlorinated polyethylene (CPE) in tension are presented. The specimens of pure LDPE, CPE, and nine types of LDPE/CPE blends, with different content of components at 10 wt.% intervals, were examined. Data on the influence of blend composition on the tensile stress-strain diagram, elastic modulus, yield stress, breaking stress, and ultimate elongation are obtained. The results of investigations of creep are also reported. It is found that the creep compliance (the total current compliance minus the elastic compliance) obeys the power law of creep.__________Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 3, pp. 391–404, May–June, 2005.     

Chern and Pontryagin Numbers in Perfect Symmetries of Spheres

The paper presents a procedure for constructing smooth actions of finite perfect groups on spheres with fixed point sets having certain prescribed properties (Theorem A); in particular, having any prescribed configuration of Chern and Pontryagin numbers (Corollary C). The main ingredients used are equivariant thickening and equivariant surgery.     

Über die Magnetischen Eigenschaften der Cobaltate Na6CoS4, Na6CoSe4 und K6CoS4

Magnetic Properties of the Cobaltates Na₆CoS₄, Na₆CoSe₄, and K₆CoS₄ The alkali metal cobalt chalcogenides Na₆CoS₄, Na₆CoSe₄, and K₆CoS₄ crystallize in the space group P6₃mc with Z = 4. The structure is characterized by isolated [CoX₄]-tetrahedra. The magnetic susceptibilities show Curie-Weiss behaviour. The deviations at low temperatures are caused by antiferromagnetic interactions. The magnetic moments are discussed with regard to ligand-field parameters.     

Assessing the Error Probability of the Model Selection Test

The asymptotic error probability of Linhart's model selection test isevaluated, and compared with the nominal significance level. We examine thecase where the expected discrepancies of the candidate models from the truemodel are asymptotically equal. The local alternatives method is employed inthe limiting operation of the asymptotic evaluation. Although the errorprobability under the null hypothesis is actually shown to be equal to orless than the level for most situations, intolerable violations of the errorcontrol are observed for nested models: It is often erroneously concludedthat the smaller model is significantly better than the larger model. Toprevent this violation, a modification of Linhart's test statistic isproposed. The effectiveness of the proposed test is confirmed throughtheoretical analysis and numerical simulations.     

Near-barrier fusion reactions induced by α on197Au,193Ir,191Ir,185Re,181Ta,121Sb and69Ga nuclei

Fusion-evaporation cross-sections for the α-induced reactions upon¹⁹⁷Au,¹⁹³Ir,¹⁹¹Ir,¹⁸⁵Re,¹⁸¹Ta,¹²¹Sb and⁶⁹Ga nuclei at bombarding energies near the Coulomb barrier have been measured by off-line observation of the γ-rays emitted in the radioactive decay of the residual nuclei using stacked foil technique. The total fusion cross-section for the systems have been compared with simple statistical model calculations using the code ALICE/91 as well as with the coupled channel calculations that include the β₂ and ν₄ slatic deformations and dynamic couplings of the vibrational/rotational states of the target and the projet tile using the code CCDEF.     

Chemical synthesis and electric properties of the conducting copolymer of aniline and o‐aminophenol

A copolymer, poly(aniline‐co‐o‐aminophenol), was prepared chemically by using ammonium peroxydisulfate as an oxidant. The monomer concentration ratio of o‐aminophenol to aniline strongly influences the copolymerization rate and properties of the copolymer. The optimum composition of a mixture for the chemical copolymerization consisted of 0.3 M aniline, 0.021 M o‐aminophenol, 0.42 M ammonium peroxydisulfate, and 2 M H₂SO₄. The result of cyclic voltammograms in a potential region of ?0.20 to 0.80 V (vs.SCE) indicates that the electrochemical activity of the copolymer prepared under the optimum condition is similar to that of polyaniline in more acid solutions. However, the copolymer still holds the good electrochemical activity until pH 11.0. Therefore, the pH dependence of the electrochemical property of the copolymer is improved, compared with poly(aniline‐co‐o‐aminophenol) prepared electrochemically, and is much better than that of polyaniline. The spectra of IR and ¹H NMR confirm that o‐aminophenol units are included in the copolymer chain, which play a key role in extending the usable pH region of the copolymer. The visible spectra of the copolymers show that a high concentration ratio of o‐aminophenol to aniline in a mixture inhibits the chain growth. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5573–5582, 2007     

Effective-Field Theory on High Spin Systems with Biaxial Crystal Field

Based on the effective-field theory with self-spin correlations and the differential operator technique,physical properties of the spin-2 system with biaxial crystal field on the simple cubic, body-centered cubic, as well as faced-centered lattice have been studied. The influences of the external longitudinal magnetic field on the magnetization,internal energy, specific heat, and susceptibility have been discussed in detail. The phenomenon that the magnetization in the ground state shows quantum effects produced by the biaxial transverse crystal field has been found.     

Structural and magnetic properties of RF sputtered FePt/Fe multilayers

Series of [FePt(4min)/Fe(t_Fe)]₁₀ multilayers have been prepared by RF magnetron sputtering and post-annealing in order to optimize their magnetic properties by structural designs. The structure, surface morphology, composition and magnetic properties of the deposited films have been characterized by X-ray diffractometer (XRD), Rutherford backscattering (RBS), scanning electron microscope (SEM), energy dispersive X-ray spectroscope (EDX) and vibrating sample magnetometer (VSM). It is found that after annealing at temperatures above 500 °C, FePt phase undergoes a phase transition from disordered FCC to ordered FCT structure, and becomes a hard magnetic phase. X-ray diffraction studies on the series of [FePt/Fe]_n multilayer with varying Fe layer thickness annealed at 500 and 600 °C show that lattice constants change with Fe layer thickness and annealing temperature. Both lattice constants a and c are smaller than those of standard ones, and lattice constant a decreases as Fe layer deposition time increases. Only a slight increase in grain size was observed as Fe layer decreased in samples annealed at 500 °C. However, the increase in grain size is large in samples annealed at 600 °C. The coercivities of [FePt/Fe]_n multilayers decrease with Fe layer deposition time, and the energy product (BH)_max reaches a maximum in the samples with Fe layer deposition time of 3 min. Comparison of magnetic properties with structure showed an almost linear relationship between the lattice constant a and the coercivities of the FePt phase.