Phase and Interfacial Tension Behavior of Certain Model Gas Condensates: Measurements and Modeling

This contribution reports on the phase and interfacial tension behavior of some model high-temperature–high-pressure gas condensates. On the one hand these types of gas condensate are becoming a subject of major interest for the oil industry, while on the other their phase and interfacial tension behavior have not been very well studied. For two different model gas condensates, both composed of the three n-alkanes, methane, butane, and decane, experimental results on their fluid phase behavior have been obtained in the temperature region 270 < T (K) < 490 and up to pressures as high as 24 MPa. Also, critical points of the two mixtures have been determined experimentally. Both mixtures show an extended retrograde region. Using the Peng–Robinson equation of state, the phase behavior of the two mixtures was modeled. In addition, the interfacial tension behavior of the model gas condensates was modeled. For that purpose, the Cahn–Hilliard theory was applied in combination with the Peng–Robinson equation of state. Satisfactory results were obtained.     

Seismic behavior of insulated hollow-brick cavity walls using quasi-static experimentation

This paper focuses on an experimental investigation of different types of insulated hollow-brick cavity walls, i.e., walls with a door opening, with a window opening and without any opening, characterized with different tie bar arrangements, subjected to slowly applied cyclic loads. The cracking and damage patterns, strength and stiffness degradation and deterioration, energy dissipation capacity and hysteretic feature are analyzed. Based on the experimental results, the formulae of calculation for the cracking load and the ultimate load of cavity wall are mathematically established. The evaluation equation of strength and stiffness degradation of walls is presented and its parameters are numerically given from regression results. The original characteristic curves of recovery force-displacement of actual specimens under cyclic loads are discussed, and then a standard recovery force-displacement model is suggested with convenient forms for implementation.     

Dynamics of Multi-Body Rotors: Numerical and Experimental FEM Analysis of the Scientific Earth Experiment Galileo Galilei Ground

Some small scientific satellites can be regarded as free, multi-body, supercritical and statorless rotors. Classical rotordynamics does not cover the dynamic behaviour and the stability analysis of such rotating systems, being focused on fixed rotors. Attitude dynamics usually deals with single rigid spacecrafts, sometimes equipped with flexible appendices like solar arrays or antennas. The case of the Galileo Galilei Ground (GGG) test facility is herewith analyzed through a numerical and experimental investigation on the dynamic behaviour of a fixed multi-body fast-spinning rotor in order to validate the design approach proposed for Galileo Galilei (GG) spacecraft.     

Coupled thermo-mechanical modelling of bulk-metallic glasses: Theory, finite-element simulations and experimental verification

A three-dimensional, finite-deformation-based constitutive model to describe the behavior of metallic glasses in the supercooled liquid region has been developed. By formulating the theory using the principles of thermodynamics and the concept of micro-force balance [Gurtin, M., 2000. On the plasticity of single crystals: free energy, microforces, plastic-strain gradients. J. Mech. Phys. Solids 48, 989-1036], a kinetic equation for the free volume concentration is derived by augmenting the Helmholtz free energy used for a conventional metallic alloy with a flow-defect free energy which depends on the free volume concentration and its spatial gradient. The developed constitutive model has also been implemented in the commercially available finite-element program ABAQUS/Explicit (2005) by writing a user-material subroutine. The constitutive parameters/functions in the model were calibrated by fitting the constitutive model to the experimental simple compression stress-strain curves conducted under a variety of strain-rates at a temperature in the supercooled liquid region [Lu, J., Ravichandran, G., Johnson, W., 2003. Deformation behavior of the Zr-Ti-Cu-Ni-Be bulk metallic glass over a wide range of strain-rates and temperatures. Acta Mater. 51, 3429-3443].With the model calibrated, the constitutive model was able to reproduce the simple compression stress-strain curves for jump-in-strain-rate experiments to good accuracy. Furthermore stress-strain responses for simple compression experiments conducted at different ambient temperatures within the supercooled liquid region were also accurately reproduced by the constitutive model. Finally, shear localization studies also show that the constitutive model can reasonably well predict the orientation of shear bands for compression experiments conducted at temperatures within the supercooled liquid region [Wang, G., Shen, J., Sun, J., Lu, Z., Stachurski, Z., Zhou, B., 2005. Compressive fracture characteristics of a Zr-based bulk metallic glass at high test temperatures. Mater. Sci. Eng. A 398, 82-87].     

TiB2增强Al2O3陶瓷刀具高速干切削摩擦磨损性能

采用TiB2增强Al2O3陶瓷刀具对淬硬钢进行高速干切削试验,利用切削高温作用下的摩擦化学反应,在刀具表面原位生成具有润滑作用的反应膜,从而实现Al2O3/TiB2陶瓷刀具的自润滑.结果表明:低速干切削时,Al2O3/TiB2陶瓷刀具的磨损机制主要表现为粘着磨损和磨料磨损;而在高速干切削时,刀具的磨损机制主要表现为氧化磨损,刀具表面经由氧化反应生成具有润滑作用的反应膜而起到固体润滑作用,从而使刀具的耐磨性能提高,随着TiB2含量和切削速度的增加,反应膜的减摩抗磨作用增强;而在切削区通入氮气时,由于刀具表面氧化膜形成受阻,刀具的抗磨能力有所降低.     

口腔环境因素对树脂牙摩擦学特性的影响

采用往复滑动摩擦磨损试验台，通过体外模拟口腔环境，考察了树脂牙同TA2钛球对摩时的摩擦磨损性能，探讨了几种口腔环境因素对树脂牙摩擦学性能的影响．结果表明：树脂牙在人工唾液介质中同钛球对摩时表现出较好的摩擦磨损性能；随着法向咬合力增加，树脂牙的主要磨损机制由轻微磨粒磨损转变为严重粘着磨损，耐磨性能变差；人工唾液和碳酸饮料长期浸泡处理对树脂牙摩擦磨损性能影响很小；而在温度0～60℃范围内经热循环老化预处理后树脂牙的耐磨性显著降低．     

滑带土动力学性质试验研究

为了研究地震高烈度区老滑坡的复活变形原因,本文对滑坡滑带土的动力学特性进行了系列研究。本次试验采用扰动土样,制样基本物理指标按滑带土的现场测试指标确定,在不固结不排水条件下,运用MTS810Teststar程控液压伺服土动三轴仪对单个样品逐级放大动应力的分级试验方法进行。侧向压力 (围压 )分别采用 100kPa、20 0kPa、300kPa三级,通过施加轴向振动荷载 (力 )模拟地震作用,振动波形为正弦波,频率为 1Hz,振幅随试样性质确定。研究结果表明,滑带土在动荷载作用下的动力学性质与其静荷载作用下的力学性质有着较大的差异,主要表现在滑带土的动应力与动应变关系的非线性、滞后性及变形积累特点,动弹性模量与动强度的显著降低以及动阻尼比的显著增大特性。这揭示了动力作用下的滑坡复活原因之一,同时为滑坡稳定性评价和动力作用下的变形机制模拟分析提供了基础资料,也为分析滑带土动力本构模型提供了基本内容。     

Constitutive framework optimized for myocardium and other high-strain, laminar materials with one fiber family

Central to this analysis is the identification of six rotation invariant scalars α_1-6 that succinctly define the strain in materials that have one family of parallel fibers arranged in laminae. These scalars were chosen so as to minimize covariance amongst the response terms in the hyperelastic limit, and they are termed strain attributes because it is necessary to distinguish them from strain invariants. The Cauchy stress t is expressed as the sum of six response terms, almost all of which are mutually orthogonal for finite strain (i.e. 14 of the 15 inner products vanish). For small deformations, the response terms are entirely orthogonal (i.e. all 15 inner products vanish). A response term is the product of a response function with its associated kinematic tensor. Each response function is a scalar partial derivative of the strain energy W with respect to a strain attribute. Applications for this theory presently include myocardium (heart muscle) which is often modeled as having muscle fibers arranged in sheets. Utility for experimental identification of strain energy functions is demonstrated by showing that common tests on incompressible materials can directly determine terms in W. Since the described set of strain attributes reduces the covariance amongst response terms, this approach may enhance the speed and precision of inverse finite element methods.     

Nonparabolic Asymptotic Limits of Solutions of the Heat Equation on $${\mathbb{R}}^N$$

In this paper, we construct solutions u(t,x) of the heat equation on such that has nontrivial limit points in as t → ∞ for certain values of μ > 0 and β > 1/2. We also show the existence of solutions of this type for nonlinear heat equations.      

Dynamic operation modes of AFM: Non-linear behavior and theoretical analysis of the stability of the AFM oscillator

The first part of this paper gives a theoretical study of the mechanics of contact of an AFM tip on viscous materials. Analytical expressions are derived showing the non-linear behaviors specifically related to the use of dynamic operation modes of AFM on viscous materials. A detailed analysis of the dissipated energy as a function of the tip indentation is presented. The second part is dedicated to a theoretical analysis investigating the domain of stability of the oscillator and the influence of the machine. The theoretical approach includes the electronic feedback loop used with the frequency modulation mode. Because the interaction between the tip and the sample produces a dynamical non-linear behavior, an unstable branch occurs that can change the stability of the oscillator. In particular, a sudden jump of the oscillating tip can be produced. In spite of the complexity of the problem, the analytical approach ends with two simple equations. The two equations provide an unambiguous way of discriminating between the contributions from the machine and the tip sample interaction.