用Josephson结电子模拟器测量磁通量子2e/h

介绍用Josephson结电子模拟器在政党温度下，模拟测量磁通量子2e/h，用模拟器来研究Josephosn结的特性。该实验可作为普通物理实验中课题设计实验的一个内容。     

Effect of Hydrogen Implantation on SIMOX SOI Materials

Hydrogen ions were implanted into separation by implantation of oxygen (SIMOX) silicon-on-insulator (SOI) wafers near the oxygen-implantation-induced damage peak under different conditions of energy and dose. It was found that the implanted hydrogen ions not only accelerate the diffusion of oxygen atoms from the annealing ambience into the wafer but also cause an outward diffusion of oxygen atoms in the buried oxide (BOX) layer. Thus, greatly broadened buried oxygen-rich (BOR) layers were formed in our experiments, which are 18%-79% broader than the BOX layer of standard SIMOX SOI wafers under the same conditions of oxygen implantation. The mechanism was discussed. A potential low cost method to fabricate SIMOX SOI wafers is proposed.     

Yb:FAP和Yb:C3S2-FAP晶体光谱的温度特性和选择激发

关键词：     

Experimental Study on Spiral Patterns in Dielectric Barrier Discharge System

Spiral patterns are obtained in a dielectric barrier discharge system with water electrodes. The dynamics of spiral formation and transition is investigated. Wavelength characteristic of spiral patterns is also studied. Correlation measurements indicate that the wavelength of spiral pattern increases with the increasing gas gap width and oscillates with the increasing drive frequency.     

第一届掺杂纳米材料发光性质学术会议

该会议为中国物理学会发光分会、中国稀土学会发光专业委员主办的国内首次纳米材料发光性质专题学术研讨会，旨在通过大会报告、专题研讨等活动，总结、交流近年来掺杂纳米发光材料及其相关应用领域所取得的研究进展和成果。在此基础上凝练科学目标、探讨和规划未来的学科发展方向并集中国内的优势资源攻克难点的科学问题，使我国在该研究领域更具国际竞争力。会议诚邀请该领域知名的专家和学者参加；在探索纳米世界之余，也将带您领略海南美丽而独特的自然景观和人文奇迹。     

Practical absorption limits of MPP absorber

The construction and properties of microperforated panel (MPP) absorber are discussed. The absorption limit of the absorber had been shown that low values of the perforate constant k = d(f/10)1/2 and the orifice diameter d (in mm) are essential for MPP to have high absorption in wide frequency band. To find the exact limits, take 1 for k as a start, because both specific resistance and high absorption require k around one. And the orifice diameter d is chosen as 0.1 mm, so that the peak absorption coefficient (resonance absorption) is at 1000 Hz, and high sound frequency may be in the absorption region. Is it possible for a single layer of such an MPP to cover the whole absorption region required in practice? The half-absorption limit is not a good criterion, because low absorption comes in also in some cases. The 0.5 absorption coefficient limit is suggested for practical region, as a standard for comparison. Absorption curves were drawn for different load resistances, of absorption coefficients versus frequency. Ordinary MPP absorber absorbs in slightly over two octaves, and the new absorber with r = 1 (specific resistance equal to the characteristic impedance in air)is slightly better than these, 2.5 octaves. The new absorbers with r > 1, are much better than these, and some satisfies high absorption in broad frequency range. Realization of these will mean great progress of MPP absorbers.     

精密垫片精冲工艺有限元分析与模具设计

精密垫片零件，如图1所示，零件材料为1Cr18Ni9Ti，强度大（σb=650MPa），有一定塑性。从零件尺寸精度看，φ4mm外圆为IT7级精度，φ4mm外圆与φ2mm内孔有很高的同轴度要求，冲裁断面与零件两端面有垂直度要求，普通冲压不能达到零件精度：从工序的角度看，有冲孔和落料工序，剪切面粗糙度Ra≤3．2μm，属于光洁冲裁范畴；另外，技术条件中要求零件两大面不得有任何划伤，且光滑平整。总体上看，该零件的冲压加工性不好，难度较大，对模具的设计、选材、制造要求都较高。