Path to achieving molecular dispersion in a dense reactive mixture

A uniform dispersion of reactants is necessary to achieve a complete reaction involving multicomponents. In this study, we have examined the role of plasticizer in the reaction of two seemingly unlikely reactants: a highly crystalline hexamethylenetetramine (HMTA) and a strongly hydrogen bonded phenol formaldehyde resin. By combining information from NMR, infrared spectroscopy and differential scanning calorimetry, we were able to determine the role of specific intermolecular interactions necessary for the plasticizer to dissolve the highly crystalline HMTA and to plasticize the phenol formaldehyde resin in this crosslinking reaction. The presence of the plasticizer increased the segmental mobility, disrupted the hydrogen bonded matrix, and freed the hydroxyl units, which further increased the solubility of the HMTA. Both the endothermic and exothermic transitions are accounted for in the calorimetric data obtained. For the first time, it is possible to obtain the effective molar ratio of each component needed to complete the crosslinking reaction efficiently. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1519–1526     

相转移催化合成增塑剂BBP和水杨醛的研究

相转移催化合成增塑剂ＢＢＰ和水杨醛的研究郭锡坤，高文华，曾东宇（汕头大学化学系，汕头５１５０６３）关键词相转移催化，季铵盐，聚乙二醇，邻苯二甲酸丁苄酯，水杨醛，增塑剂邻苯二甲酸丁苄酯（增塑剂ＢＢＰ）是一种优良的增塑剂．邻羟基苯甲醛（水杨醛）不仅是重要...     

A Novel Plasticizer for the Preparation of Thermoplastic Starch

TPS was a biodegradable material based on starch. Starch was an inexpensive and natural renewable polysaccharide, which was widely investigated as the substitute of petroleum-derived plastics. Native starch commonly existed in granule structure with about…     

On the selection of the optimal plasticizer for calix[n]arene-based ion-selective electrodes: Possible correlation between the ion selectivity and the ‘softness’ of the plasticizer

A criterion for the selection of a suitable plasticizer for calix[n]arene-based ion-selective electrodes is discussed. The cation selectivity of plasticized membranes without the ligand was first measured as a reference. The membranes can be roughly classified into two groups. The first group shows cation selectivity in the order Cs⁺+>K⁺>Na⁺>Li⁺. The membranes in the second group are made of phosphorus plasticizers, which show a selectivity in the reverse order. The plasticizers in the first group featured a linear relationship between the dipole moment of the plasticizer (calculated by a PM3 method) and the ratio of cesium selectivity to lithium selectivity. The linear relationship supports the view that the polar membrane which includes a soft plasticizer with a large dipole moment shows selectivity for Cs⁺, whereas the nonpolar membrane including the soft plasticizer with the small dipole moment shows much lower selectivity for Cs⁺. Next, 2-fluorphenyl-2-nitrophenyl ether (FPNPE) which showed the highest Cs⁺ selectivity and tris(2-ethylhexyl)phosphate (TEHP) which showed the highest Li⁺ selectivity were mixed in an appropriate ratio to make membranes with a different affinity for hard ions. The metal selectivities of several crown-based and calixarene-based ionophores were examined in these membranes. Although a few exceptions exist, the polar soft membrane is favorable when the interfering metal ion is hard, whereas the hard membrane is favorable when the interfering metal ion is soft.     

Blends of starch with ethylene vinyl alcohol copolymers: effect of water,glycerol, and amino acids as plasticizers

Blends of thermoplastic starch with poly(ethylene‐co‐vinyl alcohol) copolymer (EVOH) were melt extruded with water/glycerol as plasticizer and a series of amino acid additives. The biggest factor in end‐use mechanical properties proved to be the relative humidity (RH) during storage. Plasticized starch‐EVOH blends stored at 0 and 50% RH changed significantly over time, with, for example, the tensile strength (TS) of the glycerol‐plasticized blend increasing from 4.7 to 26.3 MPa over 8 weeks when maintained at 0% RH. In contrast, the TS of this same sample stored at 75% RH remained unchanged for 8 weeks. Amino acids provided relatively minor, but significant changes in mechanical properties with time. Based on TS, elongation‐to‐break, and modulus, it may be concluded that β‐alanine, sarcosine, and L ‐proline were more effective than glycerol at maintaining strong flexible blends. Increases in crystallinity and changes in morphology with time, as described by modulated DSC were correlated to these changes in mechanical properties. Published in 2007 by John Wiley & Sons, Ltd.     

Novel anti-inflammatory and wound healing controlled released LDH-Curcumin nanocomposite via intramuscular implantation,in-vivo study

One of the most common problems in wounds is delayed healing and complications such as infection. Therefore, the need for novel materials accelerates the healing of wounds especially abdominal wounds after surgery besides high efficiency and safety is mandatory. The rate of wound healing, anti-inflammatory and biocompatibility of Zn-Al LDH (Zn-Al layer double hydroxide) alone and loaded with Curcumin (Zn-Al LDH/Curcumin) was screened via in-vivo assays through intramuscular implantation in rat abdominal wall with intact peritoneum cavity. The implanted drugs were formed through Curcumin loaded into LDH of Zn-Al with drug release of 56.78 ± 1.51% within 24 h. The synthesized nanocomposite was characterized by (TGA/DTA) thermal analysis, (XRD) X-ray diffraction, (FESEM) Field emission scanning electron microscopy, (HRTEM) high resolution transmission electron microscope, energy dispersive X-ray (EDX) and low-temperature N₂ adsorption, pore volume and average pore size distribution. The integrity of blood circulation, inflammatory signs, wound healing rate, capacity of tissue integration, antigenicity and composite biocompatibility, auto fluorescence ability of collagen bundles and the tensile strength of the muscle were assessed histopathologically after 7 and 30 days’ post-implantation. Excellent wound healing ability was achieved with shortest length between the wound gap edges and higher tensile strength of the muscle. Besides emit florescence very well followed by good healing and tensile muscles strength in Curcumin while very low strength with scar formation in Zn-Al LDH/Curcumin in both acute and chronic wound. No signs of inflammation in Curcumin & Zn-Al LDH. No vessels obstruction or bleeding observed in both Zn-Al LDH and Curcumin more than Zn-Al LDH/Curcumin and control which examined through candling. Good healing & infiltrated immune cells in same groups through histopathological examination. This work supports the anti-inflammatory, wound healing and biocompatibility of both LDH and Curcumin with living matter, increasing their biomedical applications in this era with safety and increasing efficacy with prolonged drug release.     

Formation of polyketone particle structure by hexafluoroisopropanol solvent evaporation and effects of plasticizer addition

Few solvents are capable of dissolving polyketones (PKs). 1,1,1,3,3,3‐Hexafluoro‐2‐propanol (hexafluoroisopropanol, HFIP) is a better solvent than trifluoroethanol and m‐cresol. When HFIP was evaporated from a PK/HFIP solution, a porous cast‐film with a microparticle structure was formed because the isotactic PKs adopted a helical conformation, and convection during evaporation of the high polarity and low‐boiling‐point HFIP caused aggregation and rolling of the polymer molecules. The addition of plasticizer suppressed particle formation, improving the surface structure and mechanical properties of the film. In particular, the dielectric properties of the film improved significantly. This will enable PKs, which are rigid insulating materials, to be used as dielectric materials, broadening their range of applications. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 887–892     

Melt spinning of propylene carbonate‐plasticized poly(acrylonitrile)‐co‐poly(methyl acrylate)

The primary use of poly(acrylonitrile) (PAN) fibers, commonly referred to as acrylic fibers, is in textile applications like clothing, furniture, carpets, and awnings. All commercially available PAN fibers are processed by solution spinning; however, alternative, more cost‐effective processes like melt spinning are still highly desired. Here, the melt spinning of PAN‐co‐poly(methyl acrylate) (PMA) plasticized with propylene carbonate (PC) at 175°C is reported. The use of methyl acrylate (MA) as comonomer and PC as an external plasticizer renders the approach a combination of internal and external plasticization. Various mixtures of PAN and PC used in this work were examined by rheology, subjected to melt spinning, followed by discontinuous and continuous washing, respectively. The best fibers were derived from a PAN‐co‐PMA copolymer containing 8.1 mol‐% of MA having a number‐average molecular weight M _n of 34 000 g/mol, spun in the presence of 22.5 wt.‐% of PC. The resulting fibers were analyzed by scanning electron microscopy and wide‐angle X‐ray scattering (WAXS), and were subjected to mechanical testing.     

Toward computational design of efficient plasticizers for nylon

Polyamides are semi‐crystalline polymers useful in a wide range of applications in the plastics industry. Some applications require higher flexibility and workability of the polyamides. Therefore, plasticizers are added to ease compounding and processing procedures and produce the desired product properties. The goal of the present study was to use computational tools to estimate plasticizer efficiency in plasticizing nylon 66/6. It is known that plasticizer efficiency is greatly influenced by structural effects of the plasticizer and the nature of the polymer, and therefore in this research, a systematic study is reported to explore these factors. A homology series of esters of 4‐hydroxybenzoate with various chain lengths of the alcohol moiety was examined. Also, the efficiency of linear plasticizers was compared to branched ones and stereoisomers were considered. Plasticizer efficiency was determined by calculating cohesive energy density (CED), solubility parameters, free volume and interaction intensities of pristine nylon and the nylon–plasticizer blends. It was found that plasticizer efficiency of esters with linear alcohol moiety is higher than branched chains. Whereas plasticizer efficiency increases when the branched side chain is more bulky, no coherent trend was observed for the linear side chain of the alcohol moiety. Surprisingly, a significant difference was observed between the pair of enantiomers. The most efficient plasticizer of the eight examined was the chiral molecule (R)‐2‐Methylbutyl‐4‐Hydroxybenzoate (R‐MB4HB), increasing the free volume of the nylon by 60‐fold (3‐fold greater than the original Methyl 4‐Hydroxybenzoate (M4HB)). Copyright © 2013 John Wiley & Sons, Ltd.     

Branched plasticizers derived from eugenol via green polymerization for low/non-migration and externally/internally plasticized polyvinyl chloride materials

The synthesis of nontoxic plasticizers derived from the waste residues of the rosin-processing industry can reduce pollution and promote the high-value utilization of the waste residues of rosin. In this study, four kinds of sustainable branched plasticizers derived from a biomass resource, eugenol (derived from the waste residues of the rosin processing industry), were synthesized via one-pot solvent free polymerization and used to plasticize polyvinyl chloride (PVC). Internally plasticized PVC was fabricated using thiolated DPE (branched plasticizers based on eugenol). The thermal stability, tensile properties, microstructure, volatility behavior, and solvent extraction resistance of plasticized PVC were investigated. Compared with the behavior of the commercial plasticizer dioctyl phthalate, the thermal stability, plasticizing efficiency, and migration resistance of the branched plasticizers are superior. The acute oral toxicity dose of each branched plasticizer was extremely high at 5000 mg/kg of body weight, with no deaths among test animals. Compared with externally plasticized PVC, the internally plasticized PVC showed zero weight loss in volatility and leaching tests despite its less effective plasticization. All the branched plasticizers have potential application in plastic products.