A Photoluminescent Ag10Cu6 Cluster Stablized by a PNNP Ligand and Phenylacetylides Selectively and Reversibly Senses Ammonia in Air and Water

A photoluminescent bimetallic cluster [Ag₁₀Cu₆(bdppthi)₂(C≡CPh)₁₂(MeOH)₂(H₂O)](ClO₄)₄ ( 1 , bdppthi=N,N’-bis(diphenylphosphanylmethyl)-tetrahydroimidazole} was synthesized from the PNNP type ligand bdppthi generated in-situ. Upon excitation at 365 nm, 1 exhibited strong phosphorescent emission at 630 nm, which was selectively quenched by NH₃ in air or water. The sensing of NH₃ was rapid and recoverable, with detection limits of 53 ppm (v/v) in N₂ and 21 μmol/L (0.36 ppm, w/w) for NH₃ ⋅ H₂O in water. Cluster 1 could potentially serve as a bifunctional chemical sensor for the efficient detection of ammonia in waste-gas and waste-water.     

用标准件对梯度磁场定标

就标准厚度卡片在霍尔传感器的定标方面的应用作了有益的探讨。在纵向测量微小长度时,霍尔片处于磁场边缘位置,其对磁场的梯度更大,即灵敏度更高,且靠中心位置的线性更好。     

Sensitivity improvement of aluminum-based far-ultraviolet nearly guided-wave surface plasmon resonance sensor

An aluminum (Al) based nearly guided-wave surface plasmon resonance (NGWSPR) sensor is investigated in the far-ultraviolet (FUV) region. By simultaneously optimizing the thickness of Al and dielectric films, the sensitivity of the optimized Al-based FUV-NGWSPR sensor increases from 183°/RIU to 309°/RIU, and its figure of merit rises from 26.47 RIU^-1 to 32.59 RIU^-1 when the refractive index of dielectric increases from 2 to 5. Compared with a traditional FUV-SPR sensor without dielectric, the optimized FUV-NGWSPR sensor can realize simultaneous improvement of sensitivity and figure of merit. In addition, the FUV-NGWSPR sensor with realistic materials (diamond, Ta₂O₅, and GaN) is also investigated, and 137.84%, 52.70%, and 41.89% sensitivity improvements are achieved respectively. This work proposes a method for performance improvement of FUV-SPR sensors by exciting nearly guided-wave, and could be helpful for the high-performance SPR sensor in the short-wavelength region.     

Voltammetric Determination of Isoniazid Drug in Various Matrix by Using CuOx Decorated MW‐CNT Modified Glassy Carbon Electrode

Copper oxide decorated multi‐walled carbon nanotube (MWCNT) modified glassy carbon electrode (GCE) was prepared for determination of isoniazid (INZ) in various matrices. The electrochemical behavior of INZ was tested with the aid of Cyclic Voltammetry (CV) and quantitative experiments were performed by using Linear Sweep Voltammetry (LSV). Morphological and structural characterization of the modified electrode was performed by utilizing Scanning Electron Microscopy (SEM), X‐Ray Photoelectron Spectroscopy (XPS) while electrochemical characterization was performed by using CV and Electrochemical Impedance spectroscopy (EIS). The proposed sensor exhibited well defined anodic peak at 0.30 V for INZ at pH 6.0 medium. Under the optimum conditions, a linear relation between INZ concentration and peak current was observed in the range of 2.0×10^?7 to 5.0×10^?5 M. Limit of detection was calculated as 1.0×10^?8 M and repeatability and accuracy was found as 5.60 % and 91.0 % for 5.0 10^?7 M INZ by using 3 successive measurement, respectively. Then, the analytic performance of the electrode developed was tested by analyzing commercial tablets, artificial human serum and urine samples. The results indicated that satisfactory recoveries was observed for all issue.     

Fiber-optic reflex sensor for in-line production measurement

The paper describes experiments concerning distance measurement with fiber-optic sensor and improvement of the measurement principle. The sensor probe was well-designed with a small structure and multi-function. The novel optical fiber probe arrangement as well as the possibilities of use for complex measurement problems are explained using the measurement of an internal screw thread as an example. The experimental results show that the measurement uncertainty of the thread minor diameter can reach ±10 μm, and the stability of the measurement system is better than 0.07%.     

用AD590自组数字温度计的设计实验

本介绍了用ADS90自组数字温度计实验，说明了实验步骤和数据处理等过程。     

曲轴箱窜气量检测仪的研制

介绍了车用压差式气体流量传感器的结构设计和电测电路，指出了传感器的使用范围，由实验测出了特性曲线．该仪器可检测车用发动机曲轴箱窜气量，适用于发动机不解体故障诊断．     

用于机械振动实时监测的光纤光栅有源传感装置

把一对中心反射波长分别为1562.11nm和1562.71nm的光纤光栅粘贴在均质、等厚、等腰三角形悬臂梁上下表面作为环形腔光纤激光器端镜，当机械振动激励自由端时，通过观测激光输出脉冲，地施加于自由端的机械振动的频率进行了实时监测；观察两光栅波长漂移量差值的变化，可在0～6.1mm的范围内判断所测振动的振幅。低于100Hz时，实验结果与实际值基本吻合。     

偏振分束器对光学电流传感器稳定性的影响

采用偏振光学理论,详细分析了光学电流传感器中偏振分束器消光比的变化对传感器性能的影响,得到了偏振分束器消光比与传感器输出的关系式,并用系统实验进行了验证.理论及实验结果的吻合证明了光学电流传感器稳定性直接受偏振分束器两路消光比影响的结论.     

Fiber-Optic Chemical Sensor for Detection of NO2 Using Poly (3-Octylthiophene)

A fiber-optic chemical sensor (FOCS) for detection of nitrogen dioxide (NO₂) molecules is reported. The FOCS presents an optropode structure because of the transmission properties of the sensitive material. The NO₂ FOCS is activated by using the semiconductor polymer: regioregular head-to-tail poly(3-octylthiophene-2,5-diyl). The operation wavelength of the sensor is 543.5 nm such that a simple LED and detector can be used for the design of this device. The sensor response decreases after each exposure, demonstrating the reduction in sensitivity as well as irreversibility lower than 5%. However, its properties such as rapid response, high selectivity, high sensitivity (0.43 ± 0.01 muW/ppm), hygroscopic properties, and its operation at room temperature make this kind of FOCS a good alternative for NO₂ toxic gas detection.