Thermal conductivity of poly(vinyl chloride)/polycaprolactone blends

Thermal diffusivity, heat capacity, and density of polyvinyl chloride/polycaprolactone (PVC/PCL) blends were measured by the laser flash method, DSC, and pycnometry, respectively. The thermal conductivity of the PVC/PCL blends was determined from the results. The miscibility of the blend and crystallinity of PCL were determined by DSC. The effect of blend structure on thermal conductivity is discussed. The phase compositions of the PVC/PCL blends are of three types depending on PCL content: i.e., up to 33%, from 33 to 70%, and above 70% PCL by weight. Thermal conductivity, thermal diffusivity, and heat capacity of the PVC/PCL blends are strongly affected by the phase composition of the blend, which changes in a complicated way with PCL content. © 1994 John Wiley & Sons, Inc.     

A Simple Chaotic Circuit with Impulsive Switch Depending on Time and State

This paper presents a simple chaotic circuit consisting of two capacitors, one linear two-port VCCS and one time-state-controlled impulsive switch. The impulsive switch causes rich chaotic and periodic behavior. The circuit dynamics can be simplified into a one-dimensional return map that is piecewise linear and piecewise monotone. Using the return map, we clarify parameter conditions for existence of chaotic and periodic attractors and coexistence state of attractors.     

Laser cleaning of glass

The pulse lasers, YAG-, CO₂-, and N₂-lasers, are examined for use in the cleaning of glass. Cleaning is found to be due to the evaporation and sputtering of stains on the glass by the heat energy of the laser light. Only the N₂ laser can be used for the cleaning of the exit surface of the glass (the opposite side to the laser). A laser with a high peak power of about 10⁶J/s and short-pulse duration below 100 ns is found to be necessary in practice.     

Diversification of shotgun process

Three protocols for shotgun process are put forth in which simultaneous multi-fold reactions occur exclusively to each other. The first one involves simple combination of selective and non-selective reactions. Even if the simple protocol fails to give rise to the high selectivity, satisfactory outcome can be achieved by kinetic control or adjustment of functional groups.     

Synthesis of aromatic poly(thioether ketone)

Aromatic poly(thioether ketone)s were prepared by the direct polycondensation of aromatic dicarboxylic acids with aryl compounds containing ether or sulfide structures using phosphorus pentoxide/methanesulfonic acid (PPMA) as a condensing agent and solvent. Polycondensation proceeded smoothly and produced aromatic poly(thioether ketone)s with inherent viscosities up to 0.73 dL/g. The synthesis of substituted aryl ketones by the reaction of substituted benzoic acids with aryl compounds in PMMA was studied in detail to demonstrate the feasibility of the reaction for polymer formation. The thermogravimetry of the aromatic poly(thioether ketone)s showed a 10% weight loss in air and nitrogen at around 450 and 460°C, respectively. © 1992 John Wiley & Sons, Inc.     

Synthesis and properties of poly(amic acid)s and polyimides based on 2,2′,6,6′‐biphenyltetracarboxylic dianhydride

Poly(amic acid)s (PAAs) having the high solution stability and transmittance at 365 nm for photosensitive polyimides have been developed. PAAs with a twisted conformation in the main chains were prepared from 2,2′,6,6′‐biphenyltetracarboxylic dianhydride (2,2′,6,6′‐BPDA) and aromatic diamines. Imidization of PAAs was achieved by chemical treatment using trifluoroacetic anhydride. Among them, the PAA derived from 2,2′,6,6′‐BPDA and 4,4′‐(1,3‐phenylenedioxy)dianiline was converted to the polyimide by thermal treatment. The heating at 300 °C under nitrogen did not complete thermal imidization of PAAs having glass‐transition temperatures (T_g)s higher than 300 °C to the corresponding PIs. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6385–6393, 2006     

Effect of nitriding on grain oriented silicon steel bearing aluminum (the second study)

All kinds of high-permeability GO are manufactured using AlN as the main inhibitor. From a purely metallurgical viewpoint, three types of inhibitor preparation for high-permeability GO have been shown. They include a complete solution without nitriding, a complete precipitation with nitriding and a partial precipitation with nitriding. In this study, another possibility, i.e., a complete solution method with nitriding, was investigated to avoid the extra high-temperature slab reheating and to examine the effect of nitriding on GO bearing Al. This method can also provide the sharp Goss texture, and nitriding is shown to be very useful for changing the inhibitor intensity, depending on the primary grain size.     

Effects of natural polysaccharide addition on drug release from calcium-induced alginate gel beads

Calcium-induced alginate gel beads (Alg-Ca) containing various polysaccharides, including an alginate hydrolysate, were prepared and the drug release profiles were investigated. Hydrocortisone (HC) was gradually released from Alg-Ca into the mimic gastric fluid, while in intestinal fluid, it was quickly released with the dissolution of Alg-Ca. However, with Alg-Ca containing 5% chitin (CT), dissolution of Alg-Ca was not observed, and release of HC showed apparent zero-order kinetics. Furthermore, addition of the alginate hydrolysate altered the HC-release profile for Alg-Ca.