An on-line potentiometric sequential injection titration process analyser for the determination of acetic acid

An on-line potentiometric sequential injection titration process analyser for the determination of acetic acid is proposed. A solution of 0.1 mol L(-1) sodium chloride is used as carrier. Titration is achieved by aspirating acetic acid samples between two strong base-zone volumes into a holding coil and by channelling the stack of well-defined zones with flow reversal through a reaction coil to a potentiometric sensor where the peak widths were measured. A linear relationship between peak width and logarithm of the acid concentration was obtained in the range 1-9 g/100 mL. Vinegar samples were analysed without any sample pre-treatment. The method has a relative standard deviation of 0.4% with a sample frequency of 28 samples per hour. The results revealed good agreement between the proposed sequential injection and an automated batch titration method.     

Microstructure and electrical properties of BaTiO<Subscript>3</Subscript> and (Ba,Sr)TiO<Subscript>3</Subscript> ferroelectric thin films on nickel electrodes

Nickel thin films have been sputtered on standard Si/SiO₂ substrates with TiO₂ as an adhesive layer. The thermal stability of these substrates was analyzed. SEM images show an increase in grain size with annealing temperature. They were found to be stable till 800°C, beyond which the nickel layer disintegrated. These substrates were used for deposition of BaTiO₃ and (Ba,Sr)TiO₃ dielectric thin films under a reducing atmosphere. The dielectric thin films were processed with various pyrolysis and annealing temperatures in order to optimize the dielectric properties. Increased pyrolysis temperatures showed an increase in the grain size. Results on these nickelised substrates were finally compared with dielectric films deposited on platinized silicon substrates under identical conditions but crystallized in an oxygen atmosphere.     

Primary sequences of insulin-like growth factors 1 and 2 isolated from porcine plasma

Insulin-like growth factors 1 and 2 were purified from porcine plasma. In addition to the determination of their isoelectric points, the primary structures of both proteins were determined, using low microgram quantities of protein, by the versatile combination of time-of-flight plasma desorption mass spectrometry and automated Edman degradation. Porcine insulin-like growth factor 1 was shown to be homologous to both human and bovine proteins; the type 2 growth factor showed one mutation to both human and bovine type 2 proteins.     

Fabrication of lead titanate single crystalline nanowires by hydrothermal method and their characterization

Single crystalline nanowires of lead titanate (PbTiO₃) were fabricated by hydrothermal method at 200°C using lead acetate and n-tetrabutyl titanate as starting materials, where sodium hydroxide was served as a mineralizer. Crystalline phases, microstructure and optical properties of PbTiO₃ nanowires were investigated. The PbTiO₃ nanowires were uniform and continuous along the long axis, and were composed of single crystalline PbTiO₃ with a tetragonal perovskite structure. The diameter of a single nanowire was around 12 nm and the length reached up to 3 μm. The chemical composition of the samples and the valence states of elements were determined by X-ray photoelectron spectroscopy (XPS). The ultraviolet/visible absorption spectroscopic investigation suggested that the absorption edge of optical transition of the first excitonic state occurred at around 320 nm. A blue-green light emission peaking at about 471 nm (2.63 eV) is observed at room temperature, and the intensity of this emission increased with increasing excitation wavelength. Oxygen vacancies are responsible for the light emission of PbTiO₃ nanowires.     

Studies on stereoselective approaches to β-carboline derivatives

Transformation of β-carboline derivatives into optically active entities were studied and the de and ee values of the resulted compounds were detected. Dedicated to Professor Károly Lempert on his 80th birthday.     

Modular synthesis of block copolymers via cycloaddition of terminal azide and alkyne functionalized polymers

Polymeric building blocks containing terminal azide and alkyne functionalities are prepared via atom transfer radical polymerization (ATRP) and used to modularly synthesize block copolymers via 1,3-dipolar cycloaddition reactions, which are quantitative according to SEC measurements.     

Synthesis and crystallization kinetics of the novel ion exchanger Na<Subscript>4</Subscript>Ti<Subscript>4</Subscript>Si<Subscript>3</Subscript>O<Subscript>10</Subscript> for cesium removal

Thermodynamics and crystallization kinetics of the hydrothermal synthesis of Na₄Ti₄Si₃O₁₀ (NaTS) were systemically studied by both experiments and model simulation. Experimental results showed that the curve of crystallinity with time was a characteristic signmoid in the shape that indicated the crystallization of Na₄Ti₄Si₃O₁₀ was a typical spontaneous nucleation process on the laboratory scale. Crystallization of NaTS belongs to the liquid-liquid transformation mechanism and the reaction is endothermic (ΔH = 15.3 kJ/mol). A mathematic model of crystallization kinetics was developed to simulate the synthesis of NaTS. Runge-Kutta and simplex methods were adopted to solve the partial differential equations. Model results fitted well with the experimental data and showed that the synthesis process belongs to spontaneous nucleation and crystal growth. Moreover, the very small crystal growth constant (5.6·10⁻⁷) and gel dissolution constant (7.0·10⁻⁷) indicate they are the rate-limiting steps of the whole synthesis process.     

Groups of paramagnetic centres in coal samples with different carbon contents

Complex systems of paramagnetic centres existing in demineralised flame coal (71.4 wt% C), medium-rank coal (85.6 wt% C) and anthracite (94.9 wt% C) were analysed by electron paramagnetic resonance spectroscopy (EPR). Different groups of paramagnetic centres were searched in macerals (exinite, vitrinite, inertinite) of coals with carbon contents of 73.8 wt% C and 85.6 wt% C. Experimental EPR spectra were fitted by different superposition of theoretical lines. Total concentration of paramagnetic centres both in coal and macerals increases with carbon content in the sample. Total concentration of paramagnetic centres in macerals increases from exinite to inertinite. Four groups of paramagnetic centres were found in medium-rank coal, and only two groups exist in flame coal and anthracite. The EPR spectrum of medium-rank coal is a superposition of two broad and two narrow lines. Both broad and narrow, and two narrow lines were measured in EPR spectra of flame coal and anthracite, respectively. Two types of paramagnetic centres with broad lines and one group with narrow lines exist in exinite and vitrinite from medium-rank coal. Two narrow components were observed in EPR spectra of its inertinite. Two different broad electron paramagnetic resonance signals were detected for macerals from low-coalificated coal. Paramagnetic centres systems of medium-rank coal samples reveal the most complex character. Broad EPR lines were not observed for the higher coalificated samples, i.e., anthracite and inertinite from medium-rank coal. Narrow lines do not occur in EPR spectra of low-coalificated macerals. Strong dipolar interactions and fast spin-lattice relaxation processes are characteristic for paramagnetic centres with broad lines. Strong exchange interactions and short spin-lattice relaxation time were measured for paramagnetic centres with the narrowest EPR signals.     

An automated FTIR method for the routine quantitative determination of moisture in lubricants: An alternative to Karl Fischer titration

An accurate primary Fourier transform infrared (FTIR) method for the determination of moisture in mineral and ester based lubricants has been developed based on the extraction of moisture into dry acetonitrile. FTIR evaluation of acetonitrile extracts from new and used lubricants as well as common lubricant additives and contaminants which might co-extract indicated that phenolic constituents interfered significantly with moisture measurements. By measuring moisture at 3676 cm⁻¹ on the shoulder of the asymmetric OH stretching band, spectral interferences from extracted phenolic constituents were minimized. The spectra of calibration standards (0-2100 ppm), prepared by gravimetric addition of water to dry acetonitrile, were recorded in a 1000-μm CaF₂ transmission flow cell and produced linear standard curves having an S.D. of ∼±20 ppm. Lubricant sample preparation involved the vigorous shaking (20 min) of a 1:1.5 (w/v) mixture of lubricant and dry acetonitrile, centrifugation to separate the phases, acquisition of the FTIR spectrum of the upper acetonitrile layer, and subtraction of the spectrum of the dry acetonitrile used for extraction. A Continuous Oil Analyzer and Treatment (COAT^®) FTIR system was programmed to allow the automated analysis of acetonitrile extracts, and the methodology was validated by analyzing 58 new and used oils, independently analyzed by the Karl Fischer (KF) method. Linear regression of FTIR versus KF results for these oils produced a linear plot with a between-method S.D. of ±80 ppm. As implemented on the COAT^® system, this FTIR method is capable of analyzing 72 acetonitrile extracts/h and provides a high-speed alternative to the KF titrimetric procedures for the determination of water in lubricants.     

The effect of (natural) polyols on the initial colour of heavy metal- and zinc-free poly(vinyl chloride)

The propensity of (natural) polyols dispersed in heavy metal- and zinc-free PVC sheets to improve the initial colour, e.g. the colour during the first minutes of exposure to high processing temperatures (short-term stability), has been investigated. It is shown using W(Lab) values that the initial colour improves upon addition of polyols containing primary hydroxyl groups. The polyols act as HCl scavengers, presumably via an acid-catalysed S_N2 substitution of the primary hydroxyl groups by chloride ions. In contrast, polyols with only secondary or tertiary hydroxyl groups accelerate the thermal degradation of PVC. Notwithstanding, the efficacy of the (natural) polyols containing primary hydroxyl groups will be reduced if the polyol is susceptible to competitive acid-catalysed intramolecular cyclodehydration reactions under the processing conditions. This is substantiated by a comparison of the behaviour of mannitol and 3,4-di-O-methyl-d-mannitol. The methylated derivative, which is less prone to undergo intramolecular cyclodehydration, improves the initial colour of heavy metal- and zinc-free PVC sheets more significantly than mannitol itself.