The Potential of O‐MMT as a Reinforcing Filler for Uncured and Dynamically Cured PVC/XNBR Composites

Organic montmorillonite modified with quaternary ammonium (O‐MMT) was compounded with uncured and dynamically cured poly(vinyl chloride)/carboxylated nitrile butadiene rubber (PVC/XNBR) composites, using a Brabender Plasticorder at 130°C and 50 rpm rotor speed. The reinforcing efficiency of the O‐MMT was investigated in the uncured PVC/XNBR composite and the dynamically cured PVC/XNBR counterpart. Mixing and dynamic curing of the composites were monitored by typical torque‐time curves derived from a Brabender internal mixer. The torque‐time curves revealed that the dynamic curing process was successful and the incorporation of O‐MMT has no adverse effect on the processibility of the composites. It has been found that the introduction of crosslinks within the rubbery phase in the presence of the O‐MMT has further improved the tensile properties. DMA studies revealed that dynamically cured composite with O‐MMT showed higher storage modulus than the composite without O‐MMT. Furthermore, a one‐step tensile modulus vs. temperature curve and a related one peak tensile loss modulus vs. temperature curve were obtained, consequently, both are characteristics of a miscible polymers system. Further evidence on the composite miscibility was purchased by thermal scans from DSC, which showed a single glass transition temperature of PVC/XNBR composites. This claim was further supported by ATR‐IR spectra which revealed that hydrogen bonding is extensively involved in PVC/XNBR composites. This evidence unveiled the exact nature of the specific interactions responsible for miscibility and hence, enhanced mechanical properties. Furthermore, we proved in our studies the reinforcing role played by layered clay due to better dispersion, as well as improved interactions.     

Primary Amine‐Initiated Polymerizations of α–Amino Acid N‐Thiocarbonic Acid Anhydrosulfide

The N‐thiocarbonic acid anhydrosulfides NTAs of D,L‐leucine, D,L‐phenylalanine and sarcosine were polymerized in dioxane by addition of n‐hexylamine as initiator. Despite variation of the monomer‐initiator ratio (M/I) only low yields of oligopeptides were obtained from D,L‐Leu‐ and D,L‐Phe‐NTA. Both yields and molecular weights were almost twice as high for polymerizations of Sar‐NTA. MALDI‐TOF mass spectra confirmed that the isolated oligo‐and polypeptides possess the expected structure with one reactive amino end group. Therefore, it is surprising that the polymerizations stopped at low conversions. Two hypotheses explaining this phenomenon are discussed.     

Computational Enzyme Design

Recent developments in computational chemistry and biology have come together in the “inside‐out” approach to enzyme engineering. Proteins have been designed to catalyze reactions not previously accelerated in nature. Some of these proteins fold and act as catalysts, but the success rate is still low. The achievements and limitations of the current technology are highlighted and contrasted to other protein engineering techniques. On its own, computational “inside‐out” design can lead to the production of catalytically active and selective proteins, but their kinetic performances fall short of natural enzymes. When combined with directed evolution, molecular dynamics simulations, and crowd‐sourced structure‐prediction approaches, however, computational designs can be significantly improved in terms of binding, turnover, and thermal stability.     

On the “Tertiary Structure” of Poly‐Carbenes; Self‐Assembly of sp3‐Carbon‐Based Polymers into Liquid‐Crystalline Aggregates

The self‐assembly of poly(ethylidene acetate) (st‐PEA) into van der Waals‐stabilized liquid‐crystalline (LC) aggregates is reported. The LC behavior of these materials is unexpected, and unusual for flexible sp³‐carbon backbone polymers. Although the dense packing of polar ester functionalities along the carbon backbone of st‐PEA could perhaps be expected to lead directly to rigid‐rod behavior, molecular modeling reveals that individual st‐PEA chains are actually highly flexible and should not reveal rigid‐rod induced LC behavior. Nonetheless, st‐PEA clearly reveals LC behavior, both in solution and in the melt over a broad elevated temperature range. A combined set of experimental measurements, supported by MM/MD studies, suggests that the observed LC behavior is due to self‐aggregation of st‐PEA into higher‐order aggregates. According to MM/MD modeling st‐PEA single helices adopt a flexible helical structure with a preferred trans‐gauche syn‐syn‐anti‐anti orientation. Unexpectedly, similar modeling experiments suggest that three of these helices can self‐assemble into triple‐helical aggregates. Higher‐order assemblies were not observed in the MM/MD simulations, suggesting that the triple helix is the most stable aggregate configuration. DLS data confirmed the aggregation of st‐PEA into higher‐order structures, and suggest the formation of rod‐like particles. The dimensions derived from these light‐scattering experiments correspond with st‐PEA triple‐helix formation. Langmuir–Blodgett surface pressure–area isotherms also point to the formation of rod‐like st‐PEA aggregates with similar dimensions as st‐PEA triple helixes. Upon increasing the st‐PEA concentration, the viscosity of the polymer solution increases strongly, and at concentrations above 20 wt % st‐PEA forms an organogel. STM on this gel reveals the formation of helical aggregates on the graphite surface–solution interface with shapes and dimensions matching st‐PEA triple helices, in good agreement with the structures proposed by molecular modeling. X‐ray diffraction, WAXS, SAXS and solid state NMR spectroscopy studies suggest that st‐PEA triple helices are also present in the solid state, up to temperatures well above the melting point of st‐PEA. Formation of higher‐order aggregates explains the observed LC behavior of st‐PEA, emphasizing the importance of the “tertiary structure” of synthetic polymers on their material properties.     

Macroscopic damage modeling for silicon nitride

Modeling the damage of brittle materials is of great importance considering a variety of structural components. Prominent examples are high strength engineering ceramics. The present work is concerned with silicon nitride, a material with increasing relevance in industrial applications. In the sense of a hierarchical model structure, effective properties of micromechanical simulations were applied to macroscopic, phenomenological damage models for monotonous and cyclic loading. In the following, both models are introduced and the application of the cyclic damage model to a four point bending test is discussed. (© 2015 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim)     

Resolving Sphingolipid Isomers Using Cryogenic Infrared Spectroscopy

1‐Deoxysphingolipids are a recently described class of sphingolipids that have been shown to be associated with several disease states including diabetic and hereditary neuropathy. The identification and characterization of 1‐deoxysphingolipids and their metabolites is therefore highly important. However, exact structure determination requires a combination of sophisticated analytical techniques due to the presence of various isomers, such as ketone/alkenol isomers, carbon–carbon double‐bond (C=C) isomers and hydroxylation regioisomers. Here we demonstrate that cryogenic gas‐phase infrared (IR) spectroscopy of ionized 1‐deoxysphingolipids enables the identification and differentiation of isomers by their unique spectroscopic fingerprints. In particular, C=C bond positions and stereochemical configurations can be distinguished by specific interactions between the charged amine and the double bond. The results demonstrate the power of gas‐phase IR spectroscopy to overcome the challenge of isomer resolution in conventional mass spectrometry and pave the way for deeper analysis of the lipidome.