聚乙烯塑料在连续超临界水反应器中的油化研究

在连续超临界水（SCW）反应器中考察了反应温度、停留时间和反应压力对聚乙烯（PE）降解油化的影响。实验结果表明，在120s、25MPa下，从500℃提高到550℃，液体收率呈现先升后降的趋势，在530℃达到最大值（79%）；在520℃、25MPa下，随停留时间的延长，PE裂解程度加深，产物轻质化程度提高，导致液体收率降低，停留240s时，气体收率达到43%；反应压力对产物收率的影响较小，气、液产物中烯/烷比随反应压力的增加而增大。     

破碎-絮凝法分离细长碳纳米管与碳纤维

根据碳纤维与细长碳纳米管耐磨性能与絮凝沉降性能的差异，提出了一种有效分离细长碳纳米管与碳纤维的物理方法——破碎-絮凝法.该方法包括研磨破碎、液相分散、絮凝沉降、过滤分离等步骤，可高效去除混杂于细长碳纳米管样品中的碳纤维，同时还可去除螺旋状碳纤维及细小碳颗粒等易悬浮杂质.纯化过程对细长碳纳米管无损伤.用电子显微镜和热重分析表征了纯化效果，并初步分析了纯化机理.     

Cu/SiO2催化剂上苯胺和乙二醇一步合成吲哚的研究

采用浸渍法，制备了用于合成吲哚的Cu/SiO2催化剂，研究了不同载体和活性组分Cu对苯胺和乙二醇一步合成吲哚反应的催化活性，发现γ-Al2O3、活性炭、Na-Y，SiO2-MgO、MCM41、SiO26种载体中，SiO2是最好的载体；催化剂活性组分Cu含量为0.78mmol/gSiO2时，吲哚的收率高达88%，考察了水蒸汽、氢气、反应温度及接触时间等因素对反应性能的影响，并对催化剂进行了TG测试，得到了Cu/Sio2催化剂催化合成吲哚适应反应条件。     

CURING KINETICS AND PROPERTIES OF ACRYLIC RESIN CURED WITH AZIRIDINE CROSSLINKER

A kind of aziridine crosslinkers was synthesized and used to crosslink acrylate copolymers. The crosslinkingproperties and curing kinetics of the resin were studied. It was found that with the increase of the content of crosslinker in theemulsion, the mechanical properties and solvent resistance of the resin will be apparently improved, but its glass transitiontemperature (T_g) is very low. The lowest amount of crosslinker used in the acrylic resin emulsion is 0.25%. Curing kineticsstudied by DSC show that this curing reaction occurs readily because the apparent activation energy of the reaction is low(65.1 kJ/mol). These results demonstrate that the aziridine crosslinker is indeed a low temperature crosslinking agent and canbe used at room temperature.     

A Novel Plasticizer for the Preparation of Thermoplastic Starch

TPS was a biodegradable material based on starch. Starch was an inexpensive and natural renewable polysaccharide, which was widely investigated as the substitute of petroleum-derived plastics. Native starch commonly existed in granule structure with about…     

ADSORPTION OF 4-METHYLANILINE IN AQUEOUS SOLUTION BY BENZOYL-CONTAINING POLYMERIC ADSORBENTS

New polymeric adsorbents (ZH-02, ZH-03) containing benzoyl group for adsorbing and removing 4-methylaniline from its aqueous solutions were prepared. Studies on the isotherms and the comparison of desorption conditions evidenced through the adsorption of 4-methylaniline in water onto ZH-02 and ZH-03, namely that there are chemisorption‘s transitions at a proper higher temperature. Mini-colunm adsorption studies of 4-methylaniline on XAD-4, ZH-02 and ZH-03 at 288 K show that the breakthrough capacities are 2.39, 2.99 and 3.19 mmol/g and the total capacities are 3.45, 3.92 and 4.35 mmol/g, respectively.     

尿素法合成高结晶度类水滑石

尿素的高温分解特性被用于控制层状化合物合成过程中的pH值。室温下尿素可与硝酸盐形成均一溶液，当其高温分解时可以保证溶液内部各点的pH值始终一致，因而可获得高结晶度的水滑石样品。利用该法可合成出Mg-Al、Zn-Al及Ni-Al类水滑石，但难以合成出Co-Al，Mn-Al及Co-Cr类水滑石，相信这与不同金属离子发生沉淀时所需的pH值有关。     

Enhanced Acid/Base Catalysis in High Temperature Liquid Water

High temperature liquid water (HTLW), as an environmentally benign medium, has drawn increasing attention for organic chemical reactions and biomass conversion1-3. HTLW has a strong tendency to ionize and can act as an acid and/or base catalyst. In addition, HTLW can dissolve organic compounds to some extent allowing for a homogenous reaction within an aqueous phase. Extensive researches4-10 have been pursued on acid/base-catalysis reactions in HTLW without addition of acid or base. Howe…     

Electroreduction of α-glucose on CNT/graphite electrode modified by Zn and Zn–Fe alloy

Electroreduction of -glucose to form sorbitol on Zn/CNTs and Zn alloy/CNTs electrodes has been investigated in this paper. Carbon nanotubes (CNTs) used in this paper are grown directly on graphite disks by chemical vapor deposition. Zn and Zn alloy are electrodeposited on the activated CNTs/graphite electrode by pulse galvanostatic method. The micrographs of Zn/CNTs and Zn alloy/CNTs electrodes are characterized by scanning electron microscopy. The results show that the current efficiency of -glucose reduction on CNTs electrodes is much better than that on flat Zn electrodes. The order of the current efficiency on different electrodes is as follows: Zn/CNT (0.58) Zn–Fe/CNT (0.57)>Zn–Ni/CNT (0.43) Zn/graphite (0.42)>Zn (0.40). It indicates that CNTs have good potential application in electrosynthesis. Additionally, effects of some operating parameters, such as pH, temperature and -glucose concentration, on the current efficiency of -glucose reduction are also discussed.     

氧化锶催化性质：Ⅱ.SrO,MgO上异丙醇的分解反应

ＳｒＯ，ＭｓＯ对异丙醇的分解反应有各自的作用形式，因而产物分布也有明显差别．ＭｇＯ上异丙醇分解，在较低温度时，主要产物为丙酮和丙烯；随温度升高，生成丙烯的量增加，而丙酮的量减少，直至消失，在ＳｒＯ上，异丙醇在较高温度时反应，产物几乎为丙酮，丙烯的生成量极少。认为：产物中丙烯来源于异丙醇在催化剂表面强酸中心上的脱水；丙酮在ＭｇＯ上来源于强碱中心和酸中心协同作用异丙醇的脱氢，而在ＳｒＯ上则是ＳｒＯ表面极强的碱中心作用异丙醇而脱氢制得。