The Effect of the Spacer of Bis(biurea) Ligands on the Structure of A2L3‐type (A=anion) Phosphate Complexes

By tuning the length and rigidity of the spacer of bis(biurea) ligands L, three structural motifs of the A₂L₃ complexes (A represents anion, here orthophosphate PO₄^3?), namely helicate, mesocate, and mono‐bridged motif, have been assembled by coordination of the ligand to phosphate anion. Crystal structure analysis indicated that in the three complexes, each of the phosphate ions is coordinated by twelve hydrogen bonds from six surrounding urea groups. The anion coordination properties in solution have also been studied. The results further demonstrate the coordination behavior of phosphate ion, which shows strong tendency for coordination saturation and geometrical preference, thus allowing for the assembly of novel anion coordination‐based structures as in transition‐metal complexes.     

基于响应面法的直拉硅单晶生长工艺参数优化方法

在直拉法制备硅单晶的过程中,要得到优质的晶体必须建立合理的温度分布,而单晶炉内热场的分布与工艺参数的设定密切相关.其中以晶体转速、坩埚转速和拉速等三个工艺参数对热场分布的影响尤为显著.为了确定最佳热场分布下晶转、埚转及拉速的设定值,本文采用响应面算法通过方程拟合、回归分析等步骤求解这三个工艺参量与温度梯度之间的最佳函数模型,并在该模型下同时对这三个工艺参量进行优化分析,且通过仿真实验和拉晶实验表明该方法的有效性.     

The High Energy X-ray telescope (HE) onboard the Insight-HXMT astronomy satellite

The Insight-Hard X-ray Modulation Telescope(Insight-HXMT) is a broadband X-ray and γ-ray(1-3000 ke V) astronomy satellite. One of its three main telescopes is the High Energy X-ray telescope(HE). The main detector plane of HE comprises 18 Na I(Tl)/Cs I(Na) phoswich detectors, where Na I(Tl) is used as the primary detector to measure ~ 20-250 ke V photons incident from the field of view(FOV) defined by collimators, and Cs I(Na) is used as the active shielding detector to Na I(Tl) by pulse shape discrimination. Additionally, Cs I(Na) is used as an omnidirectional γ-ray monitor. The HE collimators have a diverse FOV,i.e. 1.1°×5.7°(15 units), 5.7°×5.7°(2 units), and blocked(1 unit). Therefore, the combined FOV of HE is approximately5.7°×5.7°. Each HE detector has a diameter of 190 mm resulting in a total geometrical area of approximately 5100 cm2, and the energy resolution is ~15% at 60 ke V. For each recorded X-ray event by HE, the timing accuracy is less than 10 μs and the deadtime is less than 10 μs. HE is used for observing spectra and temporal variability of X-ray sources in the 20-250 ke V band either by pointing observations for known sources or scanning observations to unveil new sources. Additionally, HE is used for monitoring the γ-ray burst in 0.2-3 Me V band. This paper not only presents the design and performance of HE instruments but also reports results of the on-ground calibration experiments.     

Polypyrrole Shell@3D‐Ni Metal Core Structured Electrodes for High‐Performance Supercapacitors

Three‐dimensional (3D) nanometal films serving as current collectors have attracted much interest recently owing to their promising application in high‐performance supercapacitors. In the process of the electrochemical reaction, the 3D structure can provide a short diffusion path for fast ion transport, and the highly conductive nanometal may serve as a backbone for facile electron transfer. In this work, a novel polypyrrole (PPy) shell@3D‐Ni‐core composite is developed to enhance the electrochemical performance of conventional PPy. With the introduction of a Ni metal core, the as‐prepared material exhibits a high specific capacitance (726 F g^?1 at a charge/discharge rate of 1 A g^?1), good rate capability (a decay of 33 % in C_sp with charge/discharge rates increasing from 1 to 20 A g^?1), and high cycle stability (only a small decrease of 4.2 % in C_sp after 1000 cycles at a scan rate of 100 mV s^?1). Furthermore, an aqueous symmetric supercapacitor device is fabricated by using the as‐prepared composite as electrodes; the device demonstrates a high energy density (≈21.2 Wh kg^?1) and superior long‐term cycle ability (only 4.4 % and 18.6 % loss in C_sp after 2000 and 5000 cycles, respectively).     

松木-聚氯乙烯复合材料催化热解特性的研究

通过热重法研究了松木与聚氯乙烯复合材料的催化热解特性,结果表明聚氯乙烯脱氯阶段与松木的纤维素、半纤维素热分解阶段温度区间重合,二者共热解时存在协同效应,并且HCl的释放对纤维素的脱水反应能够产生催化作用,HCl释放也对木质素的热分解及碳化反应有着明显的催化作用,导致二者共热解制备的碳化物产率提高,约为29.61%。并且利用元素分析仪、扫描电镜和能谱仪对成碳材料进行表征分析,结果表明成碳材料表面粗糙呈现多孔结构,其碳元素含量较高达到74.67%。     

Dynamic analysis of the double crank mechanism with a 3D translational clearance joint employing a variable stiffness contact force model

Nonlinear Dynamics - Oblique collisions are more likely to happen in the realistic translational joint with clearance, compared to the full front impacts. It can be a quite demanding task to...     

Raman Scattering Enhancement Based on High-Pressure High-Temperature Diamonds†

Journal of Russian Laser Research - We discuss the use of high-pressure high-temperature (HPHT) diamonds for the determination of trace amounts of various Raman active substances. The amount of the...     

蛋白质-多糖复合体系在活性物质传递中的应用

蛋白质-多糖复合体系作为生物活性物质传递系统的壁材,有着人工合成聚合物或无机物等其他材料不可比拟的多重优势。本文就蛋白质和多糖之间的连接方式及蛋白质-多糖复合体系形成传递系统的多种形式进行了综述,以及对此领域的发展趋势进行了展望。结合蛋白质和多糖的结构特点,二者之间的链接方式分为非共价结合的物理共聚,和共价结合的美拉德偶联、化学交联、酶催化交联等方式,文中分别对各种连接方式的原理和机理,以及其影响因素做了深入阐述。以蛋白质-多糖复合体系为壁材对活性物质的传递形式大体上分成乳化系统、胶束、纳米凝胶、分子复合物以及壳核结构等系统。不同的活性物质的特征和传递需求,可针对性地选择合适结构的蛋白质和多糖种类以及二者的连接方式和传递系统的形式。并且,随着研究的逐步发展和推进,此领域的发展趋势朝着智能化和靶向性的方向进行。目前活性物质的蛋白质-多糖复合体系的传递系统,还依然面临着系统设计、评价和应用等多方面的挑战,这就要求我们在更全面更深入了解认识其对活性物质影响和功效的基础上,安全合理地设计和深入细致地评价活性成分的传递系统。     

喷雾干燥-固相煅烧法制备球形钛酸狸负极材料的研究

通过喷雾干燥-固相煅烧法制备了球形钛酸钾.不同于传统喷雾干燥工艺采用固态钛源进行制备,本文采用的前驱体是钾盐,分散剂和钛酸四丁酯制备出的硝酸氧钛的混合溶液.由于制备方法中前驱体为原子级均匀分布,化学计量比可精确控制,制备出的材料颗粒细小,粒径、成分分布均匀,电化学性能优异.同时研究了不同钾钛摩尔比以及煅烧温度对球形钛酸钾的形貌和成分的影响,并研究了其作为钾离子电池电极材料的电化学性能.结果表明,钾钛摩尔比为0.816,煅烧温度为 800 ℃时钛酸钾的电化学性能最好,首圈容量 185.1 mAh/g,30 圈后容量为173.9 mAh/g,循环100圈后还有169.7 mAh/g的容量.     

Quantitative Analysis of Al in Flour Products by Laser-Induced Breakdown Spectroscopy Combined with Partial Least Squares

Journal of Applied Spectroscopy - Based on partial least squares (PLS) analysis, the effects of different smoothing points and different preprocessing methods on the accuracy and precision of the...