Sulphide based anode material for lithium rechargeable battery

In this study, lead sulphide (PbS) was prepared by the chemical bath deposition technique. The sample was characterized by X-ray diffraction (XRD), Energy Dispersive Analysis of X-rays (EDAX) and cyclic voltammetry. EDAX spectrum shows peaks attributable to lead and sulphur. The EDAX analysis also shows that the prepared sample is stoichiometric. Cyclic voltammetry experiments were recorded at 100 mV·s⁻¹ and 400 mV·s⁻¹ scan rates. Results show that the rate controlling electrochemical reaction is electron transfer. The presence of redox waves shows that the lithium intercalation and deintercalation can occur as a result of lattice expansion in PbS. There were no differences in the PbS XRD data before and after the cyclic voltammetry experiments indicating that the PbS structure is not modified upon lithium ion intercalation and deintercalation in PbS. The discharge characteristics for 35 cycles of the cell using the LiCoO₂/PbS couple is presented indicating the possible development of such materials as anode in lithium ion cells.     

CFD在燃煤细粒子凝聚过程中的应用

燃煤产生的细粒子富集了大量的有毒痕量元素,对大气环境和人类健康造成严重危害。本文针对燃煤细粒子的形成过程,在计算流体力学(CFD)的基础上,结合气溶胶动力学理论,模拟了烟气中细粒子在圆柱形流场中由于碰撞而凝聚的过程,并通过计算结果分析细粒子颗粒特征参量(速度、质量、直径和颗粒数目)随流场的变化趋势,为深入研究燃煤细粒子的形成演化机理提供理论基础。     

能谱法和催化光度法测定无机纤维中铁含量的比较研究

本文研究了铁(Ⅲ)在酸性介质中催化抗坏血酸(Vc或H2A)还原4-硝基-3’-甲基-氨基偶氮苯的褪色反应,拟定了反应的最佳条件,探讨了反应机理,建立了催化动力学测定痕量铁的新方法,该方法的检出限为2.98×10~(-11)g·mL-1,线性范围为0-200 ng·(25 mL)-1。比较了X射线能量色散谱法和催化光度法在玄武岩纤维样品中铁含量的测定,结果误差为2.89％。     

乌桕类可可脂结晶过程中表现体积变化

为了解乌桕类可可脂(CTCBE)缓冷结晶横向胀罐爆裂原因，研究CTCBE结晶过程中的膨胀特性，采用流体静力法测试了不同等温结晶条件下CTCBE结晶形成的表观密度和表观体积及其横纵向膨胀状况。结果表明，CTCBE缓冷结晶后形成外部和中部两个晶区。在5-25℃的各等温结晶范围内，当结晶温度增加时，外部结晶区域减小、表观密度变化不大；中部结晶区域增大、表观密度明显减小，CTCBE的表观体积、横向、纵向膨胀率均增大，膨胀横向大于纵向。进一步表明CTCBE在自然缓冷固化的表观体积根本上由其结晶温度决定。为有效防止横向胀罐，自然缓冷固化温度应低于10℃。     

A stable dual-wavelength fiber laser with tunable wavelength spacing using a polarization-maintaining linear cavity

We propose and experimentally demonstrate a stable dual-wavelength erbium-doped polarization-maintaining (PM) fiber laser with tunable wavelength spacing using an all-PM linear cavity that makes use of two reflection peaks from the PM fiber Bragg grating (PM-FBG). Experimental results show stable dual lasing lines with a wavelength separation of ∼0.22 nm and a large optical signal-to-noise ratio (OSNR) of over 40 dB under room temperature. By applying axial strain to the PM-FBG, the center wavelengths of the two lasing lines can be tuned over several nanometers and the wavelength separation between the lasing lines can also be tuned to as small as 0.05 nm, which, to our knowledge, is the smallest wavelength spacing ever obtained from a stable room-temperature dual-wavelength fiber laser. The proposed laser configuration has the advantages of simple structure, low loss, stable dual-wavelength operation and a very small lasing linewidth of ∼5 kHz . PACS 42.55.Wd; 42.81.-i; 42.81.Gs     

Results from GRACE/SUSY at one-loop

We report the recent development on the SUSY calculations with the help of GRACE system. GRACE/SUSY/1LOOP is the computer code which can generate Feynman diagrams in the MSSM automatically and compute one-loop amplitudes in the numerical way. We present new results of various two-body decay widths and chargino pair production at ILC (international linear collider) at one-loop level.      

A fast method to measure the thickness of removed layer from etching of SSNTD based on EDXRF

Solid state nuclear track detectors are commonly used for measurements of concentrations of radon gas and/or radon progeny. All these measurements depend critically on the thickness of the removed layer during etching. However, the thickness of removed layer calculated using the etching period does not necessarily provide a sufficiently accurate measure of the thickness. For example, the bulk etch rate depends on the strength of stirring during etching for the LR 115 detector. We propose here to measure the thickness of the removed layer by using energy-dispersive X-ray fluorescence spectrometry. In the present work, a reference silver nitrate pellet is placed beneath the LR 115 detector, and the fluorescence X-ray intensity for silver is then measured. We have found a linear relationship between the X-ray intensity and the thickness of the removed layer for LR 115 detector. This provides a fast method to measure the thickness of removed layer from etching of LR 115 detector. However, this method was found to be inapplicable for the CR-39 detector. Therefore, alternative methods have yet to be explored for the CR-39 detector.     

单光子态的产生与测量

报道了通过自发参量下转换产生单光子态的实验研究,使用中心波长425 nm的飞秒脉冲泵浦Ⅰ类非共线相位匹配的BBO晶体,在实验上得到单光子计数率为2.978×10-4,并分析了实验中的相关问题.     

2,9-disubstituted 1,10-phenanthroline nickel complexes: Syntheses,characterization, and their ethylene oligomerization

Nickel complexes 1–4 ligated with 2,9-disubstituted-1,10-phenanthroline were synthesized and characterized by FT-IR spectra and elemental analysis. The molecular structure of complex 2 was confirmed by X-ray crystal diffraction analysis. Activated with methylaluminoxane (MAO), those complexes showed moderate activities for ethylene oligomerization. Published in Kinetika i Kataliz, 2007, Vol. 48, No. 5, pp. 710–714. This article was submitted by the authors in English.     

Buckling of a stiff thin film on a compliant substrate in large deformation

A finite-deformation theory is developed to study the mechanics of thin buckled films on compliant substrates. Perturbation analysis is performed for this highly nonlinear system to obtain the analytical solution. The results agree well with experiments and finite element analysis in wavelength and amplitude. In particular, it is found that the wavelength depends on the strain. Based on the accurate wavelength and amplitude, the membrane and peak strains in thin films, and stretchability and compressibility of the system are also obtained analytically.