Saccharide Recognition by a Three-Arm-Shaped Host Having Preorganized Three-Dimensional Hydrogen-Bonding Sites

Generally, cage-shaped hosts for saccharides can bind strongly to guest molecules because of the three-dimensional preorganized hydrogen-bonding sites. However, the preparation of cage molecules is often difficult because of the low yield of the macrocyclization step. Here, we report a three-arm-shaped molecule possessing pyridine-acetylene-phenol units as a new kind of host having a preorganized three-dimensional hydrogen-bonding site. This three-arm-shaped host was readily prepared compared to a cage-shaped analogue. This host associated with lipophilic glycosides to form chiral complexes, and the association constants were sufficiently high as to be comparable to those of the cage-shaped analogue. Furthermore, this host extracted native monosaccharides into a lipophilic solvent.     

Membrane-based microchannel device for continuous quantitative extraction of dissolved free sulfide from water and from oil

Underground fluids are important natural sources of drinking water, geothermal energy, and oil-based fuels. To facilitate the surveying of such underground fluids, a novel microchannel extraction device was investigated for in-line continuous analysis and flow injection analysis of sulfide levels in water and in oil. Of the four designs investigated, the honeycomb-patterned microchannel extraction (HMCE) device was found to offer the most effective liquid–liquid extraction. In the HMCE device, a thin silicone membrane was sandwiched between two polydimethylsiloxane plates in which honeycomb-patterned microchannels had been fabricated. The identical patterns on the two plates were accurately aligned. The extracted sulfide was detected by quenching monitoring of fluorescein mercuric acetate (FMA). The sulfide extraction efficiencies from water and oil samples of the HMCE device and of three other designs (two annular and one rectangular channel) were examined theoretically and experimentally. The best performance was obtained with the HMCE device because of its thin sample layer (small diffusion distance) and large interface area. Quantitative extraction from both water and oil could be obtained using the HMCE device. The estimated limit of detection for continuous monitoring was 0.05 μM, and sulfide concentrations in the range of 0.15–10 μM could be determined when the acceptor was 5 μM FMA alkaline solution. The method was applied to natural water analysis using flow injection mode, and the data agreed with those obtained using headspace gas chromatography-flame photometric detection. The analysis of hydrogen sulfide levels in prepared oil samples was also performed. The proposed device is expected to be used for real time survey of oil wells and groundwater wells.     

Deprotection of dithioacetals with 30% hydrogen peroxide catalyzed by tantalum(V) chloride–sodium iodide or niobium(V) chloride–sodium iodide

The reaction of dithioacetals with 30% hydrogen peroxide in the presence of catalytic amounts of tantalum(V) and iodide ion effectively produced carbonyl compounds in high yields. Dithioacetals also can be deprotected using the niobium(V) catalyzed oxidation of iodide ion by hydrogen peroxide under mild conditions.     

Facile synthesis of optically active oxindoles by copper-catalyzed asymmetric monotosylation of prochiral 1,3-diols

A facile synthetic method toward optically active 3,3-disubstituted oxindoles with excellent enantioselectivity was achieved using chiral copper-catalyzed desymmetrization of prochiral 1,3-diols. The monotosylated product was transformed into oxindole derivatives efficiently.     

Synthesis of Telechelic Polystyrene by Radical Polymerization Using 1,4-Bis(p-tert-Butylphenylseleno-Methyl)benzene as a Photoiniferter

Abstract

1,4-Bis(p-tert-butylphenylselenomethyl) benzene was synthesized, and used as a bifunctional photoiniferter for the polymerization of styrene. Both the polymer yields and the number average of molecular weights (_n) of polymers increased with the polymerization. The polymerization of styrene by this iniferter permitted telechelic polystyrene containing arylseleno groups at both chain ends, and the degree of functionality was 1.9. The seleno groups of both chain ends of polystyrene were reduced quantitatively by tri-n-butyltin hydride. These seleno groups in polystyrene were also eliminated by treatment with hydrogen peroxide to give telechelic polystyrene with carbon-carbon double bond at both chain ends. Further, polystyrene with double bonds was converted to telechelic polystyrene carrying terminal functional groups as epoxy, hydroxy, and iodide group, respectively.

     

Polymerization of Acrylamide in Aqueous Solution of Poly(N‐isopropylacrylamide) at Lower Critical Solution Temperature

Acrylamide (AAm) was found to polymerize in a solution of poly(N‐isopropylacrylamide) (PNIPAAm) in water at around its lower critical solution temperature (LCST) (32°C) without any initiators. This phenomenon was specifically observed in aqueous solutions of the polymers having LCST such as PNIPAAm and poly(methylvinylether) (PMVE). AAm polymerized only when PNIPAAm and AAm were dissolved in water below LCST of PNIPAAm and then the solution was warmed up to the polymerization temperature (40°C). On the other hand, the polymerization of AAm did not proceed when AAm was added into aqueous PNIPAAm solution during and after the phase separation above 32°C. Furthermore the polymerizability of AAm was remarkably affected by the concentration and molecular weight of the PNIPAAm additives. Under the condition of lower PNIPAAm concentration (0.30 mol/L), the increase in the molecular weight of PNIPAAm considerably increased the molecular weight of the resulting PAAm but decreased the yield of PAAm. Under the condition of higher PNIPAAm concentration (0.60 mol/L) the polymerizability was not so affected by the molecular weight of PNIPAAm, while the molecular weight of PAAm formed by using higher molecular weight PNIPAAm was higher than those of PAAm formed by using lower molecular weight PNIPAAm. Moreover, the molecular weight of PAAm formed by the PNIPAAm induced polymerization of AAm was much higher than that of the polymer obtained by the radical polymerization using AIBN in THF or VA‐ 061 in water.     

Thermal behavior and dismantlability of adhesives containing various inorganic salts

As a fundamental study on the development of dismantlable adhesives containing chemically reactive materials, the thermal behavior and dismantlability of an epoxy adhesive containing one of the twenty-seven inorganic salts (chlorides, perchlorates, and nitrates) were observed. In the thermal behavior measured by the differential scanning calorimetry, epoxy adhesives with inorganic salts containing iron, copper, zinc, and aluminum cations released heats of reaction at lower temperatures than the adhesive alone or the adhesives with other inorganic salts. Since such inorganic salts were considered to be effective candidates as fillers in dismantlable adhesives, the adhesion strengths of their mixtures with the adhesive were observed after heat aging at 270 °C for 30 min. The results showed that both chloride and perchlorate salts specifically decreased the adhesion strength after heating. On the other hand, the effect of nitrate salts on the decrease in adhesion strength was low in comparison with the chloride and perchlorate salts.     

Non-destructive elemental analysis of large meteorite samples by prompt gamma-ray neutron activation analysis with the internal mono-standard method

Prompt gamma-ray neutron activation analysis (PGNAA) using the internal mono-standard method was tested for its applicability to analyzing large solid samples including irregularly shaped meteorite samples. For evaluating the accuracy and precision of the method, large quantities of the Geological Survey of Japan standardized rock powders (JB-1a, JG-1a, and JP-1) were analyzed and 12 elements (B, Na, Mg, Al, Cl, K, Ca, Ti, Mn, Fe, Sm, and Gd) were determined by using Si as an internal standard element. Analytical results were mostly in agreement with literature values within 10 %. The precision of the method was also shown to be within 10 % (1σ) for most of these elements. The analytical procedure was then applied to four stony meteorites (Allende, Kimble County, Leedey, Lake Labyrinth) and four iron meteorites (Canyon Diablo, Toluca (Mexico), Toluca (Xiquipilco), Squaw Creek) consisting of large chunks or single slabs. For stony meteorites, major elements (Mg, Al, Si, S, Ca, and Ni), minor elements (Na and Mn) and trace element (B, Cl, K, Ti, Co, and Sm) were determined with adequate accuracy. For iron meteorites, results for the Co and Ni mass fractions determined are all consistent with corresponding literature values. After the analysis, it was confirmed that the residual radioactivity remaining in the sample after PGNAA was very low and decreased down to the background level. This study shows that PGNAA with the internal mono-standard method is highly practical for determining the elemental composition of large, irregularly shaped solid samples including meteorites.