Prompt gamma-ray analysis (PGA) of meteorite samples, with emphasis on the determination of Si

Neutron-induced prompt gamma-ray analysis (PGA) was applied to seven meteorite samples (Allende, Zagami, Acfer 209, ALH77005, ALH84001, EET79001 and Neagari). Samples were irradiated in both the thermal neutron and the cold neutron guided beams of JRR-3M at JAERI. Multiple samples of an Allende standard powder were analyzed for Si using two different methods: (1) the comparison method, using a Si standard, and (2) the mono-standard method, using Fe as an internal reference element. The Si concentrations determined by these two methods are in good agreement with literature values. The analytical sensitivity for Si using the cold neutron guided beam is∼14.3× higher than that for the thermal neutron guided beam. Other elements determined (B, Ca, Ti and S) also showed higher sensitivities using the cold neutron beam. The other meteorites studied showed some anomalous B and S values likely due to the effects of terrestrial weathering/contamination.     

Prompt gamma-ray neutron activation analysis for multi-element determination in sediment samples

A facility for the irradiation of internal targets has been installed at the research reactor FRG-of the GKSS Research Center. Thermal-neutron induced prompt gamma radiation was detected by pair spectrometer. With this experimental arrangement concentrations of the major and mino elements Na, Al, Si, K, Ca, Ti, Mn, Fe, Zn, Cl, and S, as well as of the trace constituents Cr Ni, Cu Cd, and Hg of samples from a sediment core of the Elbe River could be determined. The results indicate, that prompt gamma-ray neutron activation analysis (PGNAA) is a powerful instrumental tool for a complete characterization of the main sediment constituents and for the detection of the trace elements Cd and Hg which are of considerable ecological relevance.     

Multi-element analysis of environmental samples by cold and thermal guided neutron induced prompt gamma-ray measurement

Non-destructive multi-element determination in environmental samples by neutron-induced prompt -ray analysis (PGA) has been investigated. Comparative standardization for the elements including H, B, C, N, Na, Mg, Al, Si, P, S, Cl, K, Ca, Ti, Mn, Fe, Co, Cd, Sm, Gd, Hg by PGA has been carried out using the cold and thermal guided neutron beams of JRR-3M reactor and then several environmental reference materials have been analyzed. Accuracy and precision of better than 20% were found for these elemental analyses except for H, C, N and Cl in biological samples. Detection limits in various environmental matrices were 25 to 820 ng/g for B, Cd, Sm and Gd, 1.1 to 820 g/g for H, Na, S, Cl, K, Ti, Mn, Co and Hg, and 0.031 to 10% for C, N, Mg, Al, Si, P, Ca and Fe. The present method is being applied to environmental studies of post war Persian Gulf together with INAA and ICP-MS.     

X射线荧光光谱法测定灰岩中14种主次量元素

采用X射线荧光光谱法对灰岩中的Ca,Mg,Si,K,Na,Fe,Al,Ti,P,S,Mn,Sr,Ba,Cl等14种元素进行同时测定,采用硼酸镶边垫底的粉末压样法,优化了测量条件。对比较轻的元素,采用经验影响系数法校正基体效应,对于较重的元素,采用理论α影响系数法校正基体效应。分析标准参考物质GBW 07132,各元素的精密度(RSD)为0.1%~5.9%,分析标准参考物质GBW 07130,各元素的测定值与标准值相符,该方法对各元素的测定范围宽、速度快。     

Comparative PGAA and NAA results of geological samples and standards

Concentrations of major and trace elements in volcanic rock and soil samples, including geological standard reference materials, were determined by neutron activation analysis (NAA) and prompt gamma activation analysis (PGAA), both using the k ₀-standardization method. The paper highlights the different experimental procedures, such as sample preparation, data collection and spectrum evaluation. In geological samples, PGAA gives precise results for major elements (Si, Ti, Al, Fe, Mn, Mg, Ca, Na, K and—as a unique method—for H), for some of the light trace elements as B and Cl, as well as for Sc, S, Cr, Co, Ni, Cd, Nd, Sm and Gd. NAA is sensitive for the rare earth elements, and for many major (Ti, Al, Fe, Mn, Mg, Ca, Na, K) and trace elements (e.g.: Sc, V, Cr, Co, Ni, Cu, Zn, As, Se, Rb, Sr, Zr, As, Sb, Ce, Ba, Hf, Ta, W). For most major elements the results obtained by the two methods show good agreement. The comparison of the results obtained for trace elements is not always possible, since PGAA is less sensitive and concentrations are often below its detection limits. Nevertheless, the complementarity of NAA and PGAA allows nearly panoramic analysis of geological materials.     

Neutron capture prompt gamma-ray analysis of stratospheric and groundfall ASH following the MT. ST. Helens eruption of May 18, 1980

Neutron-capture prompt γ-ray analysis (PGAA) is an exceptionally good method for the determination of the major and minor elements Na, Mg, Al, Si, K, Ca, Ti, Mn and Fe in most geological matrices. The trace elements H, B, S, Cl, Cd, Sm and Gd can often be readily measured in most geological materials. This technique was applied to volcanic ash samples collected in Washington and Montana by various groups following the May 18 eruption of the Mt. St. Helens volcano, as well as to several particulate samples collected at altitudes between 13 and 18 km by a NASA U-2 research aircraft. Groundfall ash samples show distinct elemental variations versus distance from the volcano. For example, Si/Al ratios vary from 2.85 near the volcano to about 3.70 at≽400 km to the east. Samples collected sequentially at a given location (Almira, Washington) also exhibit variations in the elemental ratios. These sequential samples were also subjected to leaching studies to determine soluble B, Cl and S. On the average, PGAA is able to account for 99.4±1.7% of the mass of each sample when the elements are considered to be in their common oxide forms. The stratospheric samples were collected May 19 on IPC cellulose filters on apparatus in a wing tank of the U-2. The PGAA results indicate that the sample from the greatest altitude resembles ashfall near the volcano, while those at lower altitudes somewhat resemble more distant ashfall.     

Characterization of deep sea sediments by INAA for radioactive waste management purposes

An instrumental neutron activation analysis method, using both reactor flux and epi-cadmium neutrons, has been developed for the determination of major, minor and trace elements in sub-seabed sediments. The method involves two different irradiations followed by three different counting periods using high-resolution Ge(Li) and low-energy photon detectors. The list of elements determined includes Ag, Al, As, Ba, Br, Ca, Ce, Cl, Co, Cr, Cs, Dy, Eu, Fe, Ga, Gd, Hf, Hg, I, In, K, La, Lu, Mg, Mn, Mo, Na, Nd, Ni, Pt, Rb, Re, Rh, Sb, Sc, Se, Si, Sm, Sn, Sr, Ta, Tb, Th, Ti, Tm, U, V. W, Yb, Zn, and Zr. The accuracy of the method has been evaluated by analyzing four different standard reference materials. The method has been applied to core samples collected from the Great Meteor East and the South Nares Abyssal Plain which are being evaluated as potential sites for the possible disposal of vitrified highly active waste.     

Improvements in food analysis by thermal neutron capture prompt gamma-ray spectrometry

Summary The thermal neutron prompt gamma-ray activation analysis (PGAA) facility, operated by the US Food and Drug Administration and National Institute of Standards and Technology Center for Neutron Research, has been redesigned to lower background radiation levels and improved analytical capabilities. Analysis of 22 element standards and food and botanical certified reference materials revealed significant sensitivity increases and lower limits of detection for H, B, C, N, Na, Al, P, S, Cl, K, Ca, Fe, and Cd. Mass fractions for these elements, as well as Mg, Al, Si, Ti, Mn, Fe, Cu, I, Zn, Sm, and Gd, were determined for 6 dietary supplements.     

Radioactivation analysis of hair a means of biological monitoring of the environment

With the aim of indicating environmental pollution effects by heavy metals on humans using hair, nondestructive activation analysis was applied to 382 normal Japanese hair samples (background level). Elemental contents of hair could be determined for Ag, Al, As, Br, Ca, Cd, Cl, Co, Cr, Cu, Fe, Hg, I, K, La, Mg, Mn, Na, S, Sb, Sc, Se, Sm, Ti, V and Zn. As these elements in hair have wide concentration ranges, the differences in concentrations distribution between groups (sex, age, permanent treatment and regional difference) are discussed. A method for hair sampling is presented.     

Trace element content of some Polish hard and brown coals

Instrumental neutron activation analysis /INAA/ method was applied to measure major, minor and trace elements in 34 samples of hard and brown coal originating from eight Polish coal mines. The elemental concentrations of 38 elements /Na, Mg, Al, Cl, K, Ca, Sc, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Ga, As, Se, Br, Rb, Sr, Mo, Ag, Cd, In, Sb, I, Cs, Ba, La, Ce, Sm, Eu, Lu, W, Au and Th/ are presented and compared with published data for coals from various origin. Enrichment factors, calculated relative to iron and the average crustal rock composition, indicated that several elements are highly enriched in Polish coals.     

Application of nondestructive X-ray fluorescence analysis to determine the element composition of medicinal plants

A nondestructive X-ray fluorescence technique has been developed to determine Na, Mg, Al, Si, P, S, Cl, K, Ca, Ti, Cr, Mn, Fe, Ni, Cu, Zn, Br, Rb, Sr, Ba, and Pb in plants. The line element intensities were measured by an S4 Pioneer X-ray sequence spectrometer (Bruker AXS, Germany). The inversely proportional relationship was obtained between the analyte line intensity and mass of the plant, pressed on boric acid backing, for elements with an atomic number 11 < Z < 20. It was found that reduction of plant mass from 6 to 1 g leads to an increase in element determination sensitivity. The detection limits for 1 g of pressed plant were evaluated as μg/g: 5–20 (Na, Mg, Al); 1–4 (Si, P, S, Cl, K, Ca, Ti, Ba, Pb); 0.4-0.8 (Cr, Mn, Fe, Ni, Br, Cu, Zn, Rb and Sr). This technique was applied to determine the element composition of violets of Violaceae family, which are used in medicine.     

A new method based on low background instrumental neutron activation analysis for major,trace and ultra-trace element determination in atmospheric mineral dust from polar ice cores

Dust found in polar ice core samples present extremely low concentrations, in addition the availability of such samples is usually strictly limited. For these reasons the chemical and physical analysis of polar ice cores is an analytical challenge. In this work a new method based on low background instrumental neutron activation analysis (LB-INAA) for the multi-elemental characterization of the insoluble fraction of dust from polar ice cores is presented. Thanks to an accurate selection of the most proper materials and procedures it was possible to reach unprecedented analytical performances, suitable for ice core analyses. The method was applied to Antarctic ice core samples. Five samples of atmospheric dust (μg size) from ice sections of the Antarctic Talos Dome ice core were prepared and analyzed. A set of 37 elements was quantified, spanning from all the major elements (Na, Mg, Al, Si, K, Ca, Ti, Mn and Fe) to trace ones, including 10 (La, Ce, Nd, Sm, Eu, Tb, Ho, Tm, Yb and Lu) of the 14 natural occurring lanthanides. The detection limits are in the range of 10⁻¹³–10⁻⁶ g, improving previous results of 1–3 orders of magnitude depending on the element; uncertainties lies between 4% and 60%.     

Elemental characterization of the new Czech meteorite ‘Morávka’ by neutron and photon activation analysis

Forty two major, minor and some trace elements were determined by activation analysis in the new Czech Morávka H5 chondrite, which fell on May 6, 2000 in the vicinity of Morávka, north-east Moravia. The elements Na, Mg, Al, Si, Cl, Ca, Ti, V, Mn, Co, Ni, and Cu were determined by means of instrumental short-time neutron activation analysis (INAA), whereas another group of elements, namely Sc, Cr, Fe, Co, Ni, Zn, As, Se, Br, Sb, La, Sm, Ir, Au and Hg were assayed using long-time INAA. Most of the rare earth elements (REE) were determined by radiochemical neutron activation analysis (RNAA) using precipitation of their oxalates, whilst for the determination of Rb and Cs an RNAA procedure based on selective sorption of the elements on ammonium phosphomolybdenate was employed. Mg, Ca, Ti, Mn, Ni, Sr, Y and Zr were determined by instrumental photon neutron activation analysis (IPAA) using the irradiation with 20 MeV bremsstrahlung from a microtron. For quality control, the U.S. Geological Survey (USGS) reference rocks basalt BCR-1 and diabase W-1 were analyzed. Moreover, the self-verification principle in activation analysis was employed to increase the credibility of the obtained results.     

Dry-Ashing Preconcentration for Micro-Reactor-Based Neutron Activation Analysis of Food and Plant Samples

The application of preconcentration by dry-ashing to the neutron activation analysis of biological samples using a SLOWPOKE-2 low-power reactor is reported. Samples of selected food crops (banana, callaloo, carrot, mango, and yam) and bioindicator plants (lichen, moss, Tillandsia sp., and tree bark) were analysed both as plant tissue, and as ashed sample. The results are presented for 21 elements. Good agreement between both procedures (<10% relative standard error) was obtained for 13 elements: Al, Ca, Cd, Cr, Fe, K, La, Mg, Mn, Na, Sm, Ti, and V. For Dy, Rb, and Zn the agreement was 10-15%. Relatively poorer agreement (>15-30%) was obtained for As, Br, Cl, and Sb. Dry ashing produced improved analytical results for those samples that were of low ash content. However, the increased background counts observed in ashed samples can sometimes negate the concentration gain, particularly in plants with high ash contents but low levels of certain elements.     

Determination of rare earth and other elements in standard biological samples by ICP-MS and activation analysis

Various rare earth elements (REEs) in standard samples supplied by the IAEA namely mussel (IAEA-142) and lichen (IAEA-336) were examined by ICP-MS and INAA. For ICP-MS, 200 mg each of the samples were dissolved in conc. nitric acid using a microwave sample-preparation system. After repeated concentration-dilution procedures (final volume; 10–20 ml), 1 ml of the sample was supplied for assay. La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm and Yb could be detected in the order of magnitude of 10⁻³ ng/g. Activation analysis carried out using 300 mg of the sample powders failed to detect REEs except La, Ce, Sm and Eu because of a strong interference due mainly to²⁴Na and³²P induced in the samples by irradiation. The REE patterns (NASC-normalized) obtained for both the organisms are of the same in their shapes except for all the values for sea animal mussel which are somewhat higher than those for land plant lichen. However, we found a large difference in the other elements contents between the two organisms. For example, Na, Cl, Mg, K, and Ca contents in mussel are about 26, 7, 4.5, 3.5, and 2 times, those in lichen. As the concentrations in the sea water for these elements is from 10² (K and Ca) to 10³ (Na, Cl and Mg) order of magnitude higher than in the land water, the result seems reasonable to assume that the higher the concentration of the element around the organisms the higher its content in the organisms.     

Feasibility of instrumental neutron activation analysis for trace element studies in natural soils

Fifty natural surface soils with strongly variable organic matter content and elemental composition were investigated to see to what extent INAA would prove useful for multi-element surveys. A conventional scheme of irradiations and decay intervals was used and 35 elements were investigated. Detection limits of the various trace elements were studied with respect to the influence of elements giving rise to major radionuclides in activated samples. For the 18 elements Na, Al, K, Sc, Cr, Mn, Fe, Co, Zn, Br, Sb, Cs, Ba, La, Sm, Hf, Th, the performance of INAA was very good. Useful results were also obtained for V, As, Se, Rb, Sr, I, Ta, and Au, while the technique appeared marginal for Cl, Zr, Mo, Ag, and Hg, and unsatisfactory for Mg, Ti, Ni, and Cd.     

Application of k 0-based internal mono-standard PGNAA for compositional characterization of cement samples

The k ₀-based internal mono-standard prompt gamma-ray neutron activation analysis (IM-PGNAA) method was used for compositional analysis of a cement standard provided by the International Atomic Energy Agency as a part of inter-laboratory comparison exercise. The PGNAA was also applied to a local cement sample for comparison purpose. The concentration ratios of elements with respect Ca were determined using the internal mono-standard method. The concentration ratios were then converted to the absolute concentrations by determining concentration of Ca in the cement using relative method. Concentrations of 11 elements were determined in both sample and standard of cement. The results of cement standard are found to be in good agreement with the certified values. The uncertainties on the elemental concentrations were in the range of 5–10 %.     

Findings of national proficiency test exercise for the determination of trace elements in edible mushroom reference material

This paper presents the results of the proficiency test exercise conducted in Pakistan for the determination of trace elements in mushroom reference material. Thirteen laboratories from different organizations of the country submitted trace elemental data on Al, As, Br, Ca, Cd, Ce, Cl, Co, Cr, Cs, Cu, Fe, Hg, K, Li, Mg, Mn, Na, P, Pb, Rb Sc, Si, Sm, Sr, Th, Zn. Results for Al, As, Br, Ca, Cd, Cl, Co, Cr, Cs, Cu, Fe, K, Mg, Mn, Na, Rb Sc, and Zn, in the mushroom material were reported by two or more participating laboratories and could be subjected to statistical evaluation. The original data of these trace elements was subjected to a computer program “Histo Version 2.1” provided by IAEA. The four outlier tests, i.e., Dixon, Grubbs, skewness and kurtosis were applied to the data sets. Consensus (overall) mean values, absolute standard deviation, relative standard deviation, standard error, median and range of values for these elements have been reported at a significance level of 0.05.     

A trace element study of commercial infant milk and cereal formulas

Three commercial infant milk formulas, one commercial infant cereal formula and one locally grown cereal used for infant feeding in Nigeria were analyzed for 17 trace elements, viz: Al, As, Br, Ca, Ce, Cl, Co, Cr, Fe, K, Mg, Mn, Na, Rb, Sb, Se and Zn. The commercial milk formulas contain adequate amounts of Ca, Cl, Co, Fe, K, Mg, Mn, Na and Zn, the locally grown cereal contains adequate amounts of Co, K, Mg, Mn and Zn and low in Ca, Cl, Fe and Na while the commercial cereal has adequate amounts of Ca, Cl, Co, K, Mg, Na and Zn. None of the samples analyzed was found to contain any elements up to threshold toxicity limits of concentrations.     

Multielement analysis of Nigerian chewing sticks by instrumental neutron activation analysis

In Nigeria, various parts of various species of native plants have long been used for dental hygiene, with reportedly considerable effectiveness. These materials are known as “chewing sticks”. This study was an effort to ascertain whether any unusual trace element concentrations might be present in Nigerian chewing sticks. Results are presented for 17 elements (Na, Mg, Al, Cl, K, Ca, Sc, V, Mn, Fe, Co, Zn, Br, Cs, La, Sm, Au) detected and measured in 12 species of such plants, via instrumental thermal-neutron activation analysis.