300kVA高温超导变压器电流引线漏热损耗的测量

电流引线是高温超导变压器的主要外部漏热来源,它的漏热量直接影响了超导变压器的经济性能,因此,引线的设计与漏热测量一直备受关注。文中构建了一个实验方案,运用量热法测量低压引线的漏热,并将试验结果与仿真预期值进行了对比和分析,从而验证了仿真设计的正确性。     

C-V法提取SiC隐埋沟道MOSFET沟道载流子浓度

本文对用C-V法提取SiC隐埋沟道MOSFET沟道载流子浓度的方法进行了理论和实验分析. pn结的存在所造成的埋沟MOS结构C-V曲线的畸变为沟道载流子浓度的提取带来一些问题. SiC/SiO₂界面上界面态的存在也会使提取出的数值与实际数值产生偏差. 本文首先从理论上分别分析了沟道深度和界面态对沟道载流子浓度提取结果的影响，然后对两种沟道深度的埋沟MOS结构C-V曲线进行了测试，提取出了沟道掺杂浓度. 在测试中，采用不同的扫描速率，分析了界面态对提取结果的影响. 理论分析结果和实验测 关键词： C-V法 SiC 隐埋沟道MOSFET 沟道载流子浓度     

Simulation of island aggregation influenced by substrate temperature, incidence kinetic energy and intensity in pulsed laser deposition

Using kinetic Monte Carlo method, we have simulated a pulsed energetic growth process in pulsed laser deposition. During the growth of film, substrate temperature mainly influences upon film morphology by directly enhancing the adatom mobility through the temperature-dependent thermal vibration. By contrast, the effect of incidence kinetic energy on film growth is complex resulting from the collisions between the incident particles and the adatoms. The results show that improving incident kinetic energy cannot significantly accelerate the migration rate of adatom but change surface microstructure and promote single adatom formation resulting in more island aggregation density. Moreover, since pulse-influx characterizes pulsed laser deposition, the intensity per pulse contributes to the evolvement of nucleation density and the results illustrate that a general scaling law different from ordinary power law still exists in energetic growth of pulsed laser deposition.     

二维非正交坐标斜方格金属光子带隙结构

金属光子带隙结构在高能加速器、微波真空电子器件和太赫兹波源等方面具有重要的应用前景.基于实空间传输矩阵理论，详细研究了非正交坐标系下二维斜方格金属光子带隙结构，给出了计算横电模、横磁模完全带隙结构的一般公式，并分析了填充系数、任意斜角及金属柱横截面对带隙结构的影响.计算结果在退化为正方格情况下时，与其他方法的计算结果取得很好的一致. 关键词： 光子晶体 金属光子带隙 传输矩阵法 微波真空电子器件     

考虑材料熔化潜热的高温高压本构

本文在修正的SCG模型基础上，提出了一种考虑了熔化潜热的高温高压本构.该本构所给出的铝的剪切模量的变化分为三个阶段：加工硬化，温度软化和熔化，并在完全熔化点处变为零.并且在前两个阶段，计算的结果与修正的SCG模型所给出的剪切模量的差别不超过4%，这一差别是在动高压实验误差范围之内的，在熔化区所给出的剪切模量与现有的实验数据相符合. 关键词： 剪切模量 熔化潜热 修正的SCG模型 动高压实验     

Simulation of a turbulent premixed open V-shaped flame using contour advection with surgery

Despite its capability of high spatial resolution, simulation of turbulent flows with traditional Lagrangian (front tracking) scheme is often discouraged by numerical instability caused by clustering of marker nodes and topological changes of fronts. Contour advection surgery (CAS), being a robust front tracking scheme, can limit the growth of front complexity during simulation without jeopardizing accuracy or efficiency. This allows it to open up an advantage over traditional front-tracking schemes. It has already been demonstrated that CAS, with incorporation of the reaction sheet model, can accurately simulate the propagation and advection of a turbulent premixed V-shaped flame. In this study, it is further tested with 10 values of vortex circulation. A range of upstream turbulence levels of 1.8–19.8% was obtained. Results indicate that upstream turbulence increase the average flame length, flame zone area and the overall burning rate. Flame surface density Σ was also estimated. Maximum values of Σ obtained lie in the range 0.1–1.4 mm⁻¹. Skewness towards the burnt region was observed in all profiles of Σ. Similar to results from laboratory experiments, it was found that Σ values decreases with upstream turbulence. From this study, the ability of CAS to cope with intense turbulence is demonstrated and a better quantitative understanding on the scheme has also been acquired.     

Solution of a Duffing-harmonic oscillator by the method of harmonic balance

The first-order harmonic balance method via first Fourier coefficient is used to construct an approximate frequency-amplitude relation for a Duffing-harmonic oscillator. This relation is in agreement with the result obtained by the Ritz procedure.     

统计优化迭代法测量质子交换波导折射率分布

提出了一种用于拟合测量渐变波导的折射率分布的新的理论处理。该方法把统计优化手段导入循环迭代法 ,可适用于费米函数这一类曲线变化范围大、且有多个自变量的函数。实验上用焦磷酸质子交换制备了LiNbO3波导样品 ,用该方法对退火后的折射率分布作了测量拟合 ,折射率拟合值与实验值的均方差为± 8.2× 10 - 4。