含氟碳菁染料聚集行为的研究

本文对五种不同结构的含氟碳菁染料的甲醇溶液及吸附在碘溴化银T 颗粒表面的聚集行为进行了研究 ,测定了照相性能 ,计算了增感倍率。Dye1 ,Dye2 ,Dye3在甲醇溶液中测得的单分子态吸收曲线 ,当取代基从C2 H5→CH3→无取代基时 ,最大吸收峰对应的波长向短波方向移动 ;乙基取代基的增感染料 (Dye1 )吸附在碘溴化银表面形成的J 聚集态峰值较高 ,对应的增感倍率也高。没有取代基的增感染料 (Dye3)不形成J 聚集 ,增感倍率低 ,有减感作用。Dye4与Dye5相比 ,Dye4具有尖而窄的J 聚集反射光谱 ,增感倍率高。结果表明 :不同结构的增感染料吸附在卤化银颗粒上形成的J 聚集态不同 ,吸收谱带窄的J 聚集态增感染料具有较高的增感倍率。     

免疫算法在车辆调度问题中的应用

免疫算法是模仿生物体高度进化、复杂的免疫系统仿生的一种智能化启发式算法。本文根据车辆调度问题的具体情况，应用免疫算法解决车辆调度中路线安排问题，并提出了一种基于分组匹配的亲和力的计算方法。实验结果表明，免疫算法能有效地应用于车辆调度中路线安排问题。     

Low Cost, High Efficiency, Gain Flattened L Band EDFA Using FBGs as C Band Seed Generators

A low cost, coolerless 980nm diode pumped, gain flattened L band EDFA with fast transient control, high pump efficiency and gain clamping effect was realized by using FBGs as C band seed generators.     

磁电垒结构中自旋极化输运性质的研究

研究了电子隧穿几类磁电垒结构的自旋极化输运性质，导出统一的传输概率公式，揭示了非 均匀磁场的分布与自旋过滤的关系，同时表明采用有效朗德因子较大的半导体材料可以显著 增强磁电垒结构的自旋过滤效果. 关键词： 磁电垒 自旋过滤 自旋电子学 自旋极化     

滤波器对偏振模色散的补偿

根据耦合非线性薛定谔方程 ,本文研究了偏振模色散如何影响各种码型的频谱 ,分析了滑频滤波器和固定滤波器对偏振模色散的补偿作用。研究结果表明 :偏振模色散对不同码型的频谱影响是不一样的 ,对色散管理孤子的频谱影响最大 ,产生新的频率分量也最多 ,而且每个新频率分量都较强 ,比入射频谱展宽许多 ;滑频滤波器和固定滤波器对偏振模色散都具有补偿作用 ,使最大可传输距离成倍增加 ,两种滤波器对偏振模色散的补偿作用相差较小 ;但是对色散管理孤子系统中的偏振模色散补偿效果最佳。     

CNx纳米管的制备、结构观察及低场致电子发射性能研究

采用高温热解法，以乙二胺为前驱液，在沉积有铁催化剂的p型硅（111）基底上制备出了定向生长的CNx纳米管.利用扫描电子显微镜、高分辨率透射电子显微镜和拉曼光谱对CNx纳米管进行了形貌观察和表征.CNx纳米管的高度在20?μm左右，直径在50—100nm之间，具有明显的“竹节状”结构，结晶有序度较差.对CNx纳米管薄膜进行低场致发射性能测试：外加电场为1.4V/μm，观察到20?μA /cm2发射电流，外电场升至2.54V/μm时发射电流达到1.280mA/cm2，在较高外电场下，没有发现电流“饱和”.这比 关键词： CNx纳米管 高温热解 “竹节状”结构 场致发射     

掺杂两种荧光染料的有机红光电致发光器件

制作了掺杂rubrene和4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7-tetramethyljulolidyl-9,enyl)-4H-pyran(DCJTB)两种荧光染料的红光有机电致发光器件。N,N’-diphenyl-N,N’-bis(1-naphthyl)-(1,1’-biphenyl)-4,4’-diamine(NPB)和掺杂的Tri-(8-hydroxyquinoline)aluminum(Alq3)分别作为空穴和电子传输层。我们发现掺rubrene和DCJTB的器件性能与只掺DCJTB的器件性能相比有所提高。器件性能的改善是因为掺入的rubrene能够促进从Alq3到DCJTB的能量转移。根据荧光衰减曲线,计算出从Alq3到DCJTB、从Alq3到rubrene以及从rubrene到DCJTB的能量转移速率分别为1.04×109,3.89×109,2.79×109s-1。可以看出能量通过rubrene从Alq3到DCJTB的转移速率是能量直接从Alq3到DCJTB的2.7倍。     

Proteins Entrapped in Silica Monoliths Prepared from Glyceroxysilanes

The preparation of discrete polyol based silane precursors derived from glycerol by a simple one-pot process is described. These polyol-based silanes could be hydrolyzed under mild pH conditions and upon gelation resulted in the formation of optically clear, monolithic, mesoporous silica. The hydrolysis and condensation reactions lead to cure rates that are very sensitive to ionic strength, but are almost unaffected by pH in contrast to those of alkoxysilanes derived from primary alcohols such as Si(OEt)₄. Residual glycerol in the silica monolith could be removed by washing, or could be left in the silica to reduce the magnitude of shrinkage during long term storage. The biocompatible glyceroxysilane precursors lead to materials that were able to retain the activity of entrapped enzymes over repeated cycles of use for periods of up to several months.     

Soluble,saturated‐red‐light‐emitting poly(p‐phenylenevinylene) containing triphenylamine units and cyano groups

A conjugated poly(p‐CN‐phenylenevinylene) (PCNPV) containing both electron‐donating triphenylamine units and electron‐withdrawing cyano groups was prepared via Knoevenagel condensation in a good yield. Gel permeation chromatography suggested that the soluble polymer had a very high weight‐average molecular weight of 309,000. A bright and saturated red emission was observed under UV excitation in solution and film. Cyclic voltammetry showed that the polymer presented quasi‐reversible oxidation with a relatively low potential because of the triphenylamine unit. A single‐layer indium tin oxide/PCNPV/Mg–Ag device emitted a bright red light (633 nm). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3947–3953, 2004     

Exploitation of introducing of catalytic centers into layer galleries of layered silicates and related epoxy nanocomposites. I. Epoxy nanocomposites derived from montmorillonite modified with catalytic surfactant‐bearing carboxyl groups

Montmorillonite (MMT) was modified with the acidified cocamidopropyl betaine (CAB) and the resulting organo‐montmorillonite (O‐MMT) was dispersed in an epoxy/methyl tetrahydrophthalic anhydride system to form epoxy nanocomposites. The intercalation and exfoliation behavior of the epoxy nanocomposites were examined by X‐ray diffraction and transmission electron microscopy. The curing behavior and thermal property were investigated by in situ Fourier transform infrared spectroscopy and DSC, respectively. The results showed that MMT could be highly intercalated by acidified CAB, and O‐MMT could be easily dispersed in epoxy resin to form intercalated/exfoliated epoxy nanocomposites. When the O‐MMT loading was lower than 8 phr (relative to 100 phr resin), exfoliated nanocomposites were achieved. The glass‐transition temperatures (T_g's) of the exfoliated nanocomposite were 20 °C higher than that of the neat resin. At higher O‐MMT loading, partial exfoliation was achieved, and those samples possessed moderately higher T_g's as compared with the neat resin. O‐MMT showed an obviously catalytic nature toward the curing of epoxy resin. The curing rate of the epoxy compound increased with O‐MMT loading. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1192–1198, 2004