Bacterial cellulose/triethanolamine based ion-conducting membranes

New bacterial cellulose (BC)–triethanolamine (TEA) ion-conducting membranes have been prepared and characterized. The samples were obtained by soaking BC membranes in triethanolamine aqueous solutions and drying. The scanning electron microscopy pictures revealed that the incorporation of TEA in BC membranes covers the cellulose microfibrils. Raman spectra exhibited BC and TEA characteristic group frequencies and thermal analysis evidenced an influence of TEA content on the sample thermal stability. The ion-conductivity as a function of the temperature showed an Arrhenius behavior increasing from 1.8 × 10^?5 S/cm at room temperature to 7.0 × 10^?4 S/cm at 80 °C for the BC–TEA 1 M sample.     

Physico-chemical and anatomical characterization of residual lignocellulosic fibers

Anatomical and physico-chemical properties of residual natural fibers (sugarcane bagasse, coconut fibers and peanut hulls) were characterized in order to evaluate their potential for use in the production of particleboard. The bulk density was determined by helium pycnometer and the chemical characteristics by using an electronic pH meter (for pH determination) on fibers dissolved in acidic and neutral detergents (to determine the levels of cellulose, hemicellulose and lignin). The anatomical characteristics were established using scanning electron microscopy coupled with an X-ray detector system, as well as energy dispersive X-ray spectroscopy. Results indicated similarities and differences between physico-chemical and anatomical characteristics of the residual lignocellulosic fibers when compared with the Pinus sp. wood commercially employed in particleboard production. Bulk density and pH for residual lignocellulosic fibers and Pinus sp. wood presented analogous values. Similar amounts of cellulose and lignin were identified between waste fibers and Pinus sp. wood. The presence of silica was identified in coconut fiber, peanut hull and sugarcane bagasse waste fibers, and may affect the mechanical characteristics of panels. Coconut and sugarcane bagasse fibers show surface pores with diameters ranging from 1.2 to 2.1 μm, below the 5 μm identified for Pinus sp. wood. Both fibers present pores distributed over their entire surface, whereas peanut hull fibers have no pores on their surface. This characteristic contributes to resin dispersion among particles, reflecting positively on the physical–mechanical properties of the panels. Particleboards produced with residual lignocellulosic fibers present similar physical–mechanical properties to those of Pinus sp. wood panels.     

Microwave hydrothermal synthesis,characterisation, and catalytic performance of Zn1−x Mn x O in cellulose conversion

Wurtzite-type Zn_1?x Mn _x O (x = 0, 0.03, 0.05, 0.07) nanostructures were successfully synthesised using a simple microwave-assisted hydrothermal route and their catalytic properties were investigated in the cellulose conversion. The morphology of the nanocatalysts is dopant-dependent. Pure ZnO presented multi-plate morphology with a flower-like shape of nanometric sizes, while the Zn_0.97Mn_0.03O sample is formed by nanoplates with the presence of spherical nanoparticles; the Zn_0.95Mn_0.05O and Zn_0.93Mn_0.07O samples are mainly formed by nanorods with the presence of a small quantity of spherical nanoparticles. The catalyst without Mn did not show any catalytic activity in the cellulose conversion. The Mn doping promoted an increase in the density of weak acid sites which, according to the catalytic results, favoured promotion of the reaction.     

Photodynamic Activity on Biofilm in Endotracheal Tubes of Patients Admitted to an Intensive Care Unit

Ventilator-associated pneumonia (VAP) is an infection that arises after endotracheal intubation affecting patients under intensive care. The presence of the endotracheal tube (ETT) is a risk factor since it is colonized by multispecies biofilm. Antimicrobial photodynamic therapy (aPDT) could be a strategy to decontaminate ETTs. We verify if methylene blue (MB) associated with external illumination of the ETT could be an alternative to destroy biofilm. We performed an in vitro and ex vivo study. In vitro study was performed with P. aeruginosa biofilm grew over ETT for 7 days. After treatment, the surviving cells were cultured for 3 days and the biofilm was analyzed by crystal violet absorbance. Ex vivo study employed ETT obtained from extubated patients. aPDT was performed with MB (100 µm ) and red LED (λ = 640±20 nm). We quantified the biofilm thickness and used scanning electron microscopy and fluorescence technique to verify morphological and functional changes after aPDT. Our results showed that bacteria remain susceptible to aPDT after sequential treatments. We also attested that aPDT can reduce biofilm thickness, disrupt biofilm attachment from ETT surface and kill microbial cells. These data suggest that aPDT should be investigated to decrease VAP incidence via ETT decontamination.     

A comparative multi-reference configuration interaction study of the low-lying states of two thione isomers of thiophenol

Multi-reference configuration interaction, MR-CI (including extensivity corrections, named +Q), calculations were performed on the S₀–S₃ states of cyclohexa-2,4-diene-1-thione (thione 24 ) and cyclohexa-2,5-diene-1-thione (thione 25 ), which are thione isomers of thiophenol. Several types of uncontracted MR-CIS and MR-CISD wavefunctions were employed, comprising MR-CI expansions as large as ~365 × 10⁶ configuration state functions. The nature of the studied excited states was characterized. Vertical excitation energies (ΔE) and oscillator strengths (f) were computed. The most intense transitions (S₀ → S₂ for 24 and S₀ → S₃ for 25 ) did not change with the wavefunction, although a variation as large as ~1 eV was obtained for the S₃ state of 24 , at the highest (MR-CI+Q) level. On the other hand, ΔE changed at most by ~0.56 eV for 25 as the wavefunction changes, at the same level. The S₁ state of both thiones was found to have nπ* character and is in the visible region. For 24 , S₂ and S₃ are ππ* and nπ* states, respectively, while for 25 the reverse order is obtained. S₂ and S₃ are in the range ~3.5 to 5.2 eV, again at the highest level. It is the first time that the excited states of the title molecules are studied. The computed results agree with the experimental onset of photoreactions of thiones 24 and 25 found by Reva et al (Phys. Chem. Chem. Phys., 2015 , 17, 4888).     

Application of Ionic Liquids in Electrochemistry—Recent Advances

In this review, the roles of room temperature ionic liquids (RTILs) and RTIL based solvent systems as proposed alternatives for conventional organic electrolyte solutions are described. Ionic liquids are introduced as well as the relevant properties for their use in electrochemistry (reduction of ohmic losses), such as diffusive molecular motion and ionic conductivity. We have restricted ourselves to provide a survey on the latest, most representative developments and progress made in the use of ionic liquids as electrolytes, in particular achieved by the cyclic voltammetry technique. Thus, the present review comprises literature from 2015 onward covering the different aspects of RTILs, from the knowledge of these media to the use of their properties for electrochemical processes. Out of the scope of this review are heat transfer applications, medical or biological applications, and multiphasic reactions.     

Selective Oxidation of Ethane to Acetic Acid Catalyzed by a C-Scorpionate Iron(II) Complex: A Homogeneous vs. Heterogeneous Comparison

The direct, one-pot oxidation of ethane to acetic acid was, for the first time, performed using a C-scorpionate complex anchored onto a magnetic core-shell support, the Fe₃O₄/TiO₂/[FeCl₂{κ³-HC(pz)₃}] composite. This catalytic system, where the magnetic catalyst is easily recovered and reused, is highly selective to the acetic acid synthesis. The performed green metrics calculations highlight the “greeness” of the new ethane oxidation procedure.     

Flow-through amperometric methods for detection of the bioactive compound quercetin: performance of glassy carbon and screen-printed carbon electrodes

Journal of Solid State Electrochemistry - Rapid methods using batch injection analysis (BIA) with amperometric detection were developed for the determination of quercetin extracted from the...     

Influence of fused deposition modeling parameters on the mechanical properties of ABS parts

This work aims to determine the influence of fused deposition modeling (FDM) printing parameters on the mechanical properties of parts fabricated on an Ultimaker2 printer with acrylonitrile butadiene styrene (ABS). The effect of several parameters such as interlayer cooling time (ILCT), nozzle diameter, infill density, raster angle and layer thickness on the ultimate tensile strength, yield strength, and elastic modulus of produced parts was evaluated. Two independent studies were conducted: a first study dedicated to the ILCT and a second study where the influence of other parameters was evaluated through a design of experiments (DoE) approach. Both studies were carried out through the execution of standard tensile tests. The statistical analysis of tensile tests results was processed with the ANOVA methodology. The obtained results indicate that a reduced ILCT improves the tensile strength of parts. It is shown that nozzle diameter and infill density are the parameters that most influence the mechanical properties of ABS, with the upper range selected values improving the studied mechanical properties. The raster angle configuration of (?45^o/45^o) benefits UTS and yield strength of ABS samples. Interactions of nozzle diameter on layer thickness were detected. It was observed that smaller layer thickness promotes a higher elastic modulus and UTS; however, for thinner layers (0.06‐0.10 mm), no significant differences were found on strength of samples due to potential high distortion levels.