Detecting pore size distribution of activated carbon by low-field nuclear magnetic resonance

In this study, the transverse relaxation time (T₂) of activated carbon (AC) in different relative environment humidity was detected firstly by low-field nuclear magnetic resonance (LFNMR). The pore size (diameter) of AC distributions was calculated by the relationship between T₂ and surface relaxation rate (ρ), where ρ was obtained by the detection of nine porous materials with known pore size. The results showed that the pore size distributions of AC calculated by ρ < 0.19 nm/ms were in good agreement with that obtained by nitrogen adsorption method and proved that LFNMR as a new detection method was feasible for characterizing AC pore size distribution.     

二次阳极氧化方法制备有序多孔氧化铝膜

通过二次阳极氧化方法制备多孔氧化铝膜与一次阳极氧化方法制备多孔氧化铝膜孔排布规律性的对比 ,结果发现 ,二次阳极氧化方法制取的多孔氧化铝膜孔排布规律性明显好于一次阳极氧化法制取的多孔膜 .在几个微米范围内 ,孔呈理想的六角排布 .去除一次阳极氧化膜后 ,二次阳极氧化得以在更良好的表面进行 ,制取的氧化铝膜孔规律性和有序度更高 .有序区域的尺寸与晶粒内的亚晶大小有一定关系     

大气气溶胶粒子光吸收系数的测量

 采用核孔过滤膜累积气溶胶粒子的方法设计了气溶胶粒子光吸收系数的测量系统。该系统由双光路组成,可以减小光路损耗和电路噪声带来的各种测量误差。同时，具有体积小、光路易于调节、可进行实时测量、定标容易等特点。用200和400nm孔径的过滤膜，分别测量了实验室内大气气溶胶粒子对不同波长激光的吸收系数。随着累积时间的增加，系统的测量精度也不断的提高，在累积时间为900s时，系统测量误差为9.849×10^-6/m。     

The Modeling of Velocity Enhancement in Polymer Flooding

In single-phase polymer flooding experiments it has repeatedly been observed that the average velocity of the polymer molecules is higher than the average velocity of the water molecules. This effect is incorporated in many conventional Enhanced Oil Recovery (EOR) simulators by the introduction of a constant velocity enhancement factor. In this paper we show that, in absence of dispersion, a constant enhancement factor in the mathematical model for two-phase polymer flow (Buckley--Leverett displacement) leads to ill-posedness of the model equations. We propose a saturation dependent enhancement factor, derived from a model based on percolation concepts, for which this problem does not occur.     

Standardization of Methods for Characterizing the Surface Geometry of Solids

Since a comprehensive survey published in 1999 [1] much work was done in standardizing measuring methods to characterize the surface geometry of dispersed and/or porous solids and to certify reference materials. The present paper is an extension of a short communication [2]. It gives a survey on existing standards and reports on new drafts and proposals.     

Synthesis and adsorption properties of gold nanoparticles within pores of surface‐functional porous polymer microspheres

Mesoporous polymer microspheres with gold (Au) nanoparticles inside their pores were prepared considering their surface functionality and porosity. The Au/polymer composite microspheres prepared were characterized by transmission electron microscope (TEM), X‐ray diffraction (XRD), and Brunauer–Emmett–Teller (BET) techniques. The results showed that the adsorption of Au nanoparticles could be increased by imparting the pore structure and surface‐functional groups into the supporting polymer microspheres (in this study, poly (ethylene glycol dimethacrylate‐co‐acrylonitrile) and poly (EGDMA‐co‐AN) system). Above all, from this study, it was established that the porosity of the polymer microspheres is the most important factor that determines the distribution and adsorption amount of face‐centered cubic (fcc) Au nanoparticles in the final products. Our study showed that the continuous adsorption of Au nanoparticles with the aid of the large surface area and surface interaction sites formed more favorably the Au/polymer composite microspheres. The BET measurements of Au/poly(EGDMA‐co‐AN) composite microspheres reveals that the adsorption of Au nanoparticles into the pores kept the pore structure intact and made it more porous. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5627–5635, 2004     

TG and DSC study of the properties of coked molecular sieve catalyst

A cracking catalyst designatedSRNY was manufactured from a commercialSRNY molecular sieve (M.S.). The support consisted of kaolin, clay and SiO₂. The coking behaviour of theSRNY M.S., the support and the catalyst were examined with light diesel oil (LDO) as feedstock in a microreactor. The physico-chemical properties of both fresh and aged samples, subjected to or not subjected to the cracking reaction ofLDO, were sequentially characterized by means of pore structure determination and thermal analysis. The pore structure included the specific surface area and the pore volume or porosity. Thermal analysis methods used included TG and DSC. The results indicated that all coked samples exhibited obvious changes in surface pore structure and acidity in comparison with non-coked samples. Their specific surface area and acid amount decreased with increase in the coke content of the samples. The apparent activation energy data obtained from decoking samples in an air flow, using the temperature-programmed oxidation (TPO) method, showed that the kinetic parameters of theSRNY M.S. differed from those of theSRNY catalyst and its support.     

Na2CO3调质钙基脱硫剂硫化机理实验研究

对经Na2CO3溶液调质石灰石煅烧产物CaO的物理结构及硫化特性进行了研究,发现同等条件下调质后石灰石煅烧产物CaO(M-CaO)比未经调质的CaO(N-CaO)具有更高的钙转化率.利用XRD技术对CaO晶体结构进行了测定,通过比较二者的晶胞参数和晶格畸变度等并结合其孔特性,证实M-CaO之所以比N-CaO具有更高的钙转化率,是由于M-CaO比N-CaO具有更高的晶体缺陷浓度,使得在硫化反应过程中通过产物层的扩散具有更高的离子扩散率.     

同步辐射小角x射线散射方法研究由城市固体垃圾制备的活性炭

应用同步辐射小角x射线散射方法研究了由不同城市固体垃圾制备而成的活性炭的孔结构-结果发现利用木类、纸张、塑料这三类典型垃圾组分的热解残余物为原料制备中孔发达的活性炭是可行的-活性炭的形态和结构取决于垃圾热解残余物的组分和热解程度等因素- 关键词： 小角x射线散射 活性炭 分形维数 平均孔径