Desorption behavior of a surfactant in a linear low‐density polyethylene blend at elevated temperatures

The desorption behavior of a surfactant in a linear low‐density polyethylene (LLDPE) blend at elevated temperatures of 50, 70, and 80 °C was studied with Fourier transform infrared spectroscopy. The composition of the LLDPE blend was 70:30 LLDPE/low‐density polyethylene. Three different specimens (II, III, and IV) were prepared with various compositions of a small molecular penetrant, sorbitan palmitate (SPAN‐40), and a migration controller, poly(ethylene acrylic acid) (EAA), in the LLDPE blend. The calculated diffusion coefficient (D) of SPAN‐40 in specimens II, III, and IV, between 50 and 80 °C, varied from 1.74 × 10^?11 to 6.79 × 10^?11 cm²/s, from 1.10 × 10^?11 to 5.75 × 10^?11 cm²/s, and from 0.58 × 10^?11 to 4.75 × 10^?11 cm²/s, respectively. In addition, the calculated activation energies (E_D) of specimens II, III, and IV, from the plotting of ln D versus 1/T between 50 and 80 °C, were 42.9, 52.7, and 65.6 kJ/mol, respectively. These values were different from those obtained between 25 and 50 °C and were believed to have been influenced by the interference of Tinuvin (a UV stabilizer) at elevated temperatures higher than 50 °C. Although the desorption rate of SPAN‐40 increased with the temperature and decreased with the EAA content, the observed spectral behavior did not depend on the temperature and time. For all specimens stored over 50 °C, the peak at 1739 cm^?1 decreased in a few days and subsequently increased with a peak shift toward 1730 cm^?1. This arose from the carbonyl stretching vibration of Tinuvin, possibly because of oxidation or degradation at elevated temperatures. In addition, the incorporation of EAA into the LLDPE blend suppressed the desorption rate of SPAN‐40 and retarded the appearance of the 1730 cm^?1 peak. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1114–1126, 2004     

铁基添加剂增强细水雾灭火性能的实验研究

采用实验模拟的方法,研究了添加氯化亚铁的细水雾在不同添加剂浓度、不同喷头压力下,熄灭不同性质的液体池火的性能。实验结果表明:添加有氯化亚铁的细水雾,其灭火性能发生了显著变化。存在一个最佳的灭火浓度,其对应的灭火时间最短,耗水量最少,灭火效率最高。细水雾喷头的工作压力和燃料的性质也对细水雾的灭火性能有影响:工作压力越大,细水雾的平均灭火时间越短。在相同的实验条件下,细水雾扑灭煤油池火的时间要短于扑灭酒精池火的时间。     

考虑流体湿润性影响的核沸腾RohsenoW修正模型

添加界面活性剂的核沸腾在改变蒸气泡生长特性的同时，主要是强化了对流换热．本文考虑流体湿润性影响，对核沸腾换热沿用最广的对流类比模型－Ｒｏｈｓｅｎｏｗ模型进行了修正．通过对实验数据的检验，表明修正后的模型预示值与实测结果吻合很好．     

Thermal properties of poly(styrene) containing brominated aryl phosphate additives

General purpose poly(styrene) is a large volume commodity polymer widely used in a range of applications. For many of these the presence of an additive to impart some flammability resistance is required. Most commonly, brominated aromatics are used for this purpose. As the polymer undergoes combustion these compounds decompose to generate bromine atoms and/or hydrogen bromide which escape to the gas phase and trap flame propagating radicals. While these species are effective in inhibiting flame propagation they present the opportunity for loss of halogen to the atmosphere. For this reason, the use of these compounds is being limited in some parts of the world. Phosphorus compounds, on the other had, impart a flame retarding influence by promoting char formation at the surface of the burning polymer. This prevents heat feedback to the polymer and consequent pyrolysis to generate fuel fragments. The combination of both bromine and phosphorus present in a single compound might generate a superior flame-retarding additive in that both modes of retardancy might be promoted simultaneously. Should this be the case smaller amounts of additive might be necessary to achieve a satisfactory level of flame retardancy. A series of such additives, brominated aryl phosphates, has been synthesized and fully characterized spectroscopically. Blends of these additives, at various levels, with poly(styrene) have been examined by DSC, TG and in the UL-94 flame test. The flammability of the polymer is dramatically diminished by the presence of the additive.     

Effect of BaBiO3 and Ba0.6K0.4BiO3 additives on the rechargeability of manganese oxide cathodes in alkaline cells

The effect of the incorporation of small amounts (1–5 wt%) of semiconducting BaBiO₃ and metallic Ba_0.6K_0.4BiO₃ additives on the rechargeability of electrolytic manganese dioxide (EMD) cathodes in alkaline cells in the one-electron regime has been investigated. Both the BaBiO₃ and Ba_0.6K_0.4BiO₃ additives lead to better cyclability compared to the previously known binary oxide additive Bi₂O₃. X-ray diffraction patterns recorded before and after 30 cycles as well as cyclic voltammograms recorded after first and 30 cycles reveal that the better cyclability in the presence of BaBiO₃ and Ba_0.6K_0.4BiO₃ additives is due to the suppression of the formation of unwanted, electrochemically inactive birnessite and hausmannite phases and a shifting of the second-electron capacity of Mn to higher potentials.     

The hydrolysis mechanism of bis(2,4-di-tert-butyl)pentaerythritol diphosphite (Alkanox P24): An atmospheric pressure photoionisation mass spectrometric study

Alkanox P24 is a commercial phosphite antioxidant, well known in the literature for its excellent processing stability. As in the case of many processing phosphites, however, Alkanox P24 might undergo hydrolysis when exposed to small amounts of water. A number of products proposed recently in the hydrolytic pathway of the phosphite [Ortuoste N, Allen NS, Papanastasiou M, McMahon A, Edge M, Johnson B, et al. Polym Degrad Stab; 2006;91:195-211] are investigated in this study by atmospheric pressure ionisation-mass spectrometry (API-MS). The applicability of atmospheric pressure photoionisation (APPI) and atmospheric pressure chemical ionisation (APCI) ion sources is tested and the ion formation characteristics of Alkanox P24 are compared in both sources. In positive ion mode, ionisation of the parent phosphite occurred by protonation. In negative ion mode no pseudo-molecular ion peak was detected and the deprotonated species were more dominant in APPI. This source was employed further for the investigation of the hydrolysis products, since it exhibited lower limits of detection. High performance liquid chromatography (HPLC) with single ion monitoring (SIM) detection was used for the separation of the species formed. Hydrolysis of the phosphite proceeded via the scission of the two P-O_phenol bonds exclusively to give 2,4-di-tert-butyl phenol quantitatively as a final product.     

Effect of ionic additives on the elution of sodium aryl sulfonates in supercritical fluid chromatography

Addition of a small amount of polar solvent (i.e., modifier) to CO2 in packed column supercritical fluid chromatography (SFC) has shown major improvements in both polar analyte solubility and interaction of the polar analyte with the stationary phase. Recently, the addition of an ionic component (i.e., additive) to the primary modifier by one of us has been shown to extend even further the application of SFC to polar analytes. In this work, the effect of various ionic additives on the elution of ionic compounds, such as sodium 4-dodecylbenzene sulfonate and sodium 4-octylbenene sulfonate, has been studied. The additives were lithium acetate, ammonium acetate, tetramethylammonium acetate, tetrabutylammonium acetate, and ammonium chloride dissolved in methanol. Three stationary phases with different degrees of deactivation were considered: conventional cyanopropyl, deltabond cyanopropyl, and bare silica. The effect of additive concentration and additive functionality on analyte retention was investigated. Sodium 4-dodecylbenzene sulfonate was successfully eluted using all the additives with good peak shape under isocratic/isobaric/isothermal conditions. Different additives, however, yielded different retention times and in some cases different peak shapes.     

2,2''''-联吡啶和亚铁氰化钾对乙醛酸化学镀铜的影响

以乙醛酸作还原剂、Na2EDTA为络合剂、2,2'-联吡啶和亚铁氰化钾作为添加剂组成化学镀铜体系,研究了两种添加剂对化学镀铜速率、镀层表面形貌、组成和结构的影响.结果表明:添加适量的2,2'-联吡啶和亚铁氰化钾,不仅提高了镀液的稳定性,而且使沉积速率增加1倍.这两种添加剂的同时使用,使镀层颜色变亮,形貌发生变化.所得镀层是多晶铜,没有发现夹杂Cu20.     

Acceleration of the Passerini reaction in the presence of nucleophilic additives

An accelerating effect of nucleophilic additives was revealed for the Passerini multi-component reaction. The influence of aqueous solutions on the reaction rate was studied in detail and the direct involvement of water in the bond-making step was attributed as the basis of an accelerating effect. Other nucleophiles were tested as alternatives to water; as a result N-hydroxysuccinimide is proposed as an accelerant of the Passerini reaction.     

Thermal behavior of glutamic acid and its sodium,lithium and ammonium salts

Glutamic acid (H2_glu) and its lithium, sodium and ammonium monosalts were submitted to thermal analysis using thermogravimetry (TG) and differential thermal analysis (DTA). The main goal of these studies was to compare the relative thermal stability and to evaluate the effect of the counter ion in the thermal decomposition pathways. Salts were obtained by direct neutralization of the purified acid with LiOH, NaOH or NH₄OH and were characterized by elemental analysis (C, H and N) and IR spectroscopy. Decomposition occurred after conversion to the pyroglutamic acid or the respective pyroglutamates and ammonium salt loosing NH₃ being converted to H₂glu before decomposition.