投料顺序对动态硫化PP／EPDM性能影响及其机理的研究

针对ＰＰ降解在ＰＰ／ＥＰＤＭ动态硫化中对体系产生的不利影响。考察了四种不同投料顺序对ＰＰ／ＥＰＤＭ动态硫化物的冲击韧性，加工流动性，交联程度和断面形貌等宏观和微观性能，并进行了不同ＥＰＤＭ含量的动态硫化和非硫化ＰＰ／ＥＰＤＭ的性能比较。结果表明，优化投料顺序能实现对动态硫化体系中化学反应对象和化学反应程度的有效干预。     

EVA增容PP/HDPE共混体系的形态结构与性能

采用乙烯－醋酸乙烯酯共聚物（ＥＶＡ）作为聚丙烯（ＰＰ）／高密度聚乙烯（ＨＤＰＥ）共混体系的增容剂,通过冲击实验、拉伸实验、示差量热扫描仪（ＤＳＣ）和扫描电镜（ＳＥＭ）,系统地研究了共混体系的性能与其形态结构之间的。结果表明,ＥＶＡ是ＰＰ／ＨＤＰＥ共混物较好物增容剂,ＥＶＡ可以使ＰＰ、ＨＤＰＥ的晶相结构受到一定程度的破坏,增加ＰＰ和ＨＤＰＥ的相容性,同时共混物的冲击韧性明显提高。     

PP/LDPE共混体系的辐射效应

研究了在多官能团单体—三烯丙基异氰脲酸酯存在下ＰＰ／ＬＤＰＥ共混体系接受γ－辐射的效果。用溶解度参数和ＴＥＭ技术评估了共混体系的相容性与多官能团单体在共混体系中的分布，并用ＳＥＭ、ＤＳＣ、动态力学等方法对共混体系相容性进行了表征。结果表明，ＰＰ／ＬＤＰＥ是不相容的共混体系，三烯丙基异氰脲酸酯主要分布在共混体系的相界面区域，辐照强化了共混体系的相间结合，增加了界面厚度，改善了共混体系的相容性。     

离散物Surlyn对PBT／PP共混体系的力学性能及形态结构的影响

用力学性能测试，ＤＭＡ、ＳＥＭ等方法研究了离聚物Ｓｕｒｌｙｎ对ＰＢＴ／ＰＰ共混体系的力学性能及形态结构的影响。结果表明，在ＰＢＴ／ＰＰ共混体系中引入少量Ｓｕｒｌｙｎ可以改善界面的粘接性，从而改善其力学性能。     

聚丙烯／顺丁橡胶动态硫化共混物的交联行为和结晶性能的研究

研究了聚丙烯／顺丁橡胶动态硫化共混物橡胶相的交联行为、动态硫化共混物的结晶行为和结晶结构。结果表明，顺丁橡胶的加入对ＰＰ的熔点无明显影响，但结晶度降低。动态硫共化共混物在低于熔点处另有一熔化转变。动态硫化使共混物中ＰＰ的结晶速率提高。     

PP／LDPE共混体系的辐射效

研究了在多官能团单体－三烯丙基异氰脲酸酯存在下ＰＰ／ＬＤＰＥ共混体系接受γ－辐射的效果。用溶解度参数和ＴＥＭ技术评估了共 体系的相容性与多官能团单体在共混体系中的分布，并用ＳＥＭ、ＤＣＳ、动态力学等方法对共混体系相容性进行了表征。     

离聚物Surlyn对PBT/PP共混体系的力学性能及形态结构的影响

用力学性能测试、ＤＭＡ、ＳＥＭ等方法研究了离聚物Ｓｕｒｌｙｎ对ＰＢＴ／ＰＰ共混体系的力学性能及形态结构的影响。结果表明，在ＰＢＴ／ＰＰ共混体系中引入少量Ｓｕｒｌｙｎ可以改善界面的粘接性，从而改善其力学性能。当共混体系中ＰＢＴ／ＰＰ的组份比不变（９０／１０）且Ｓｕｒｌｙｎ的含量为６ｐｈｒ左右时，共混物的冲击强度出现极大值；而弯曲强度在Ｓｕｒｌｙｎ含量为１－２ｐｈｒ左右时有最大值。当共混体系中Ｓｕｒｌｙｎ的含量不变（６ｐｈｒ）时，其力学性能随ＰＰ含量的增加而下降。用玻璃纤维增强共混体系，可显著提高力学性能。     

低乙烯含量聚丙烯共聚物结晶成核剂研究

利用ＤＳＣ和偏光显微镜等手段研究了部分成核剂对聚丙烯均聚物（ＰＰ）、低乙烯含量聚丙烯共聚物及聚丙烯／聚乙烯（ＰＰ／ＰＥ）共混物结晶行为的影响，结果表明所用成核剂对ＰＰ和改性ＰＰ具有一定的普适性。聚丙烯共聚物中，由于链结构规整性变差，成核剂的作用显得特别突出，而ＰＰ／ＰＥ共混物中，由于成核剂向ＰＥ相迁移而使其对ＰＰ结晶的成核效率降低。     

高真空强静电场下半熔融态处理压电聚合物--PA11/PVDF共混物晶体结构和显微形态研究

使用ＷＡＸＤ和ＳＥＭ研究了高真空强静电场下半熔融态处理不同共混比例（ＰＡ１１／ＰＶＤＦ＝０／１００、２０／８０、４０／６０、６０／８０、８０／２０、１００／０）的压电聚合的ＰＡ１１／ＰＶＤＦ共混物压片的晶体结构和形态。ＷＡＸＤ分析表明,纯ＰＶＤＦ经不同强度静电场半熔融态处理后晶体结构并没有发生改变,均为β型ＰＶＤＦ;而纯ＰＡ１１经不同强度静电场半熔融态处理后晶体结构发生了改变,随电场强度的增加,部分ＰＡ１１由α型向δ′型转变。ＰＡ１１／ＰＶＤＦ共混物经不同强度静电场半熔融态处理后,当ＰＡ１１含量较小时,其结晶相为由β型ＰＶＤＦ和α型ＰＡ１１组成的混合相,并没有新相产生;而当ＰＡ１１含量较大时,共混物中的部分ＰＡ１１同样由α型向δ′型ＰＡ１１组成的混合相。ＳＥＭ观察表明,在无电场时,纯ＰＡ１１和纯ＰＶＤＦ呈混乱状     

高密度聚乙烯与乙烯丙烯辛烯－1共聚物共混体系的相容性

用ＤＳＣ和ＷＡＸＤ方法研究了高密度聚乙烯／聚（乙烯丙烯辛烯－１）（ＨＤＰＥ／ＥＰＯ）共混体系的结晶性能。共混物的ＤＳＣ曲线皆呈单峰，表明共混体系形成了共晶。晶胞参数ａ及结晶度随共混物组成而变，进一步证明ＨＤＰＥ／ＥＰＯ共混体系的相容性．     

共混过程中EPDM/PP共混热塑弹性体的结构、形态和性能的变化

用SEM,TEM,DSC,WAXD和有效网链密度(v_e)测定,研究了共混时间长短和返炼对EPDM/PP共混物结构和性能的影响。两相分散随共混时间和返炼而更趋均匀。随共混时间,PP结晶度(x_c)先行降低然后升高,抗张强度正相反,v_e则降低x_e和v_e返炼后总是较一次共混降低。影响强度的因素主要是两相分散均匀和两相界面的相互渗透。     

乙丙橡胶/聚丙烯共混体系的界面相互渗透

本文用X射线衍射仪、差热分析仪、动态力学扭摆仪和测定有效网链密度等方法,研究了乙丙橡胶/聚丙烯(EPDM/PP)共混体系中PP的非晶部分和EPDM的相互渗透。EPDM和PP不具有互溶性,但PP的非晶部分和EPDM两相界面处有较强的相互渗透,即部分互容性。有效链密度和性能间关系的数据表明,共混体系不一定存在硫化胶那样的对应关系。     

BRITTLE-DUCTILE TRANSITION OF PP/EPDM/ELASTOMERIC NANO-PARTICLE TERNARY BLENDS

The brittle-ductile transition is a very important phenomenon for polymer toughening. Polypropylene （PP） is often toughened by using rubbers, e.g., ethylene-propylene diene monomer （EPDM） has often been used as a modifier. In this article, the toughening of PP by using a new kind of rubber, known as elastomeric nano-particle （ENP）, and the brittleductile transition of PP/EPDM/ENP was studied. Compared to PP/EPDM binary blends, the brittle-ductile transition of PP/EPDM/ENP ternary blends occurred at lower EPDM contents. SEM experiment was carried out to investigate the etched and impact-fractured surfaces. ENP alone had no effect on the impact strength of PP, however, with the same EPDM content, PP/EPDM/ENP ternary blends had smaller particle size, better dispersion and smaller interparticle distance in contrary to PP/EPDM binary blends, which promoted the brittle-ductile transition to occur earlier.     

Study on Dynamic Vulcanized EPDM/PP Thermoplastic Elastomer

Based upon the THE,HAAK RHEOCORD 90 and Wx-ray observation,a study was made on the structure and property of ethylene-propylene-ethlidene norborene (EPDM)/polyprolene (PP) blending systems ,and the experimental results were fully explained. (1) The effect of Mooney viscosity (ML)of EPDM、 melt flow rate(MFR) of peroxide(DCP) and mixing steps on mechanical properties of EPDM/PP blends was studied. The results showed that the mechanical and process properties of EPDM?PP thermoplastic elastomers were better using EPDM with the ML of 60 and PP with MFR of 7.5g/10min as matrix,DCP with the content of 1.2 per cent with the help of twostep curing process at the temperature of 170-175 ℃.     

iPP/HDPE/EPDM三元共混体系的组分分布、相容性和结晶行为

 用DSC、¹³C-NMR、SEM和WAXD等方法研究了IPP/HDPE/EPDM三元共混体系的组分分布、相容性和结晶行为。实验结果表明,EPDM与PE组分的相容性优于与PP组分的相容性,多数EPDM分子链段能够分布在PE组分中;EPDM含量为15％时,共混物相容性最好,SEM照片呈现晶体微区的互连或网络状结构;随EPDM含量增加,总结晶度X_c减小,其中PE组分结晶度X_cE有较大幅度地降低,PP组分结晶度X_cp基本没有变化,这可以根据EPDM和PE、PP之间相容性的差异以及PE、PP两组分在冷却过程中不同的结晶行为来解释。     

Reactive melt blends of thermoplastic polyolefins,MAH‐g‐PP and nylon 6

Reactive melt blends of an ethylene‐propylene‐diene terpolymer (EPDM) based thermoplastic elastomer (TPE), maleic anhydride grafted polypropylene (MAH‐g‐PP), and nylon 6 were prepared in a single screw extruder and evaluated in terms of morphological, rheological, thermal, dynamic mechanical, and mechanical properties of the blends. It was found that MAH‐g‐PP‐co‐nylon 6 copolymers were in situ formed and acted as effective compatibilizers for polypropylene (PP) and nylon 6. Phase separation of PP and EPDM in TPE increased with the addition and increasing amount of MAH‐g‐PP and nylon 6, leading to decreased glass transition temperature (T_g) of TPE and increased crystalline melting temperature (T_m) of PP. Copyright © 2004 John Wiley & Sons, Ltd.     

Damage Studies of Brittle-Ductile Transition in PP EPDM Blends

Damage zones of brittle-ductile (B-D) transition in PP/EPDM blends are studied in this paper. The contribution of crazing and shear yielding zones in damage zones to energy dissipation of blends was measured with computer image analysis (CIA) and the transition of shear yielding zone (A_(sh)) with rubber volume fraction (V_f) was also manipulated. Results showed that the B-D transition of impact strength of blends corresponded to the fracture mechanism in PP/EPDM blends, from matrix crazing to matrix shear yielding. In addition, two new parameters, density of energy dissipation for crazing zone (F_(cz)) and for shear yielding zone (F_(sh)), are first obtained in this paper. The value of F_(sh) is about four times larger than that of F_(cz) for PP/EPDM blends, which confirmed that the matrix shear yielding is a more effective way of energy dissipation in blends.     

Morphology development and phase inversion during dynamic vulcanisation of EPDM/PP blends

Morphology development and phase inversion were investigated during dynamic vulcanisation of ethylene–propylene–diene terpolymer (EPDM)/polypropylene (PP) blends. The effects of viscosity ratio and cross-linking reactions were also addressed. EPDM/PP blends were dynamically vulcanised in a Haake batch mixer using resole and SnCl₂ as cross-linking agents. The morphology development and cross-linking degree with reaction time were followed by morphology analysis (SEM and TEM) and measurement of EPDM gel content, respectively. For the same reaction time, it was found that the EPDM gel content decreased when the low-molecular-weight EPDM was used. As a result, the morphological development was delayed and the phase-inversion point was shifted to higher reaction times, allowing us to monitor morphological development during a thermoplastic vulcanisate (TPV) preparation. Using the low-molecular-weight EPDM and increasing the PP viscosity accelerated the morphological development, shifting phase-inversion to lower reaction times. While blend composition influenced final TPV morphology, it had a minor effect on the mechanism of morphological development. A correlation between cross-linking degree and morphology development was established. The results obtained allowed to propose a mechanism of morphology development during dynamic vulcanisation of the EPDM/PP blends, including phase inversion.     

iPP/HDPE/EPDM三元共混体系的组分分布、相容性和结晶行为

用DSC、~(13)C-NMR、SEM和WAXD等方法研究了IPP/HDPE/EPDM三元共混体系的组分分布、相容性和结晶行为。实验结果表明,EPDM与PE组分的相容性优于与PP组分的相容性,多数EPDM分子链段能够分布在PE组分中;EPDM含量为15％时,共混物相容性最好,SEM照片呈现晶体微区的互连或网络状结构;随EPDM含量增加,总结晶度X_c减小,其中PE组分结晶度X_(cE)有较大幅度地降低,PP组分结晶度X_(cp)基本没有变化,这可以根据EPDM和PE、PP之间相容性的差异以及PE、PP两组分在冷却过程中不同的结晶行为来解释。     

Uncross‐linked polypropylene (PP)/ethylene‐propylene‐diene (EPDM)/multi walled carbon nanotube (MWCNT) and dynamically vulcanized PP/EPDM/MWCNT nanocomposites

In this study, relatively large amounts of polypropylene (PP), ethylene‐propylene‐diene (EPDM), and multi‐walled carbon nanotube (MWCNT) were melt‐mixed with and without DCP. Dynamically vulcanized PP/EPDM (TPV)/MWCNT nanocomposites were prepared by two methods: the MWCNTs were added either before or after the dynamic vulcanization of the blends. The effects of composition, rotor speed, and dynamic vulcanization on their surface resistivity were investigated. The surface resistivity of uncross‐linked PP/EPDM/MWCNT nanocomposites increases with increasing the content of EPDM. At PP/EPDM (70/30 wt%) nanocomposite with 1.5 phr MWCNT, slightly lower surface resistivity is obtained by increasing the rotor speed during mixing. However, for PP/EPDM (50/50 wt%) and PP/EPDM (30/70 wt%) nanocomposites, surface resistivity decreases with increasing the rotor speed from 30 to 60 rpm. But further increase in rotor speed (90 rpm) leads to an increase of surface resistivity. When the MWCNTs were added after the dynamic vulcanization of the blends, the surface resistivity of TPV70/MWCNTnanocomposite is lower than that of uncross‐linked PP/EPDM/MWCNT nanocomposite. However, when the MWCNTs were added before the dynamic vulcanization of the blends, the surface resistivity of TPV70/MWCNT nanocomposite is >10¹² Ω/square. Copyright © 2010 John Wiley & Sons, Ltd.