Amplified impedimetric aptasensor based on gold nanoparticles covalently bound graphene sheet for the picomolar detection of ochratoxin A

An amplified electrochemical impedimetric aptasensor for ochratoxin A (OTA) was developed with picomolar sensitivity. A facile route to fabricate gold nanoparticles covalently bound reduced graphene oxide (AuNPs–rGO) resulted in a large number of well-dispersed AuNPs on graphene sheets with tremendous binding sites for DNA, since the single rGO sheet and each AuNP can be loaded with hundreds of DNA strands. An aptasensor with sandwich model was fabricated which involved thiolated capture DNA immobilized on a gold electrode to capture the aptamer, then the sensing interface was incubated with OTA at a desired concentration, followed by AuNPs–rGO functionalized reporter DNA hybridized with the residual aptamers. By exploiting the AuNPs–rGO as an excellent signal amplified platform, a single hybridization event between aptamer and reporter DNA was translated into more than 10⁷ redox events, leading to a substantial increase in charge-transfer resistance (R_ct) by 7∼ orders of magnitude compared with that of the free aptamer modified electrode. Such designed aptasensor showed a decreased response of R_ct to the increase of OTA concentrations over a wide range of 1 pg mL⁻¹–50 ng mL⁻¹ and could detect extremely low OTA concentration, namely, 0.3 pg mL⁻¹ or 0.74 pM, which was much lower than that of most other existed impedimetric aptasensors. The signal amplification platform presented here would provide a promising model for the aptamer-based detection with a direct impedimetric method.     

Monitoring microbial populations of sulfate-reducing bacteria using an impedimetric immunosensor based on agglutination assay

An impedimetric immunosensor was fabricated for rapid and non-labeled detection of sulfate-reducing bacteria, Desulforibrio caledoiensis (SRB) by immobilizing lectin-Concanavalin A using an agglutination assay. The immobilization of lectin was conducted using amine coupling on the surface of a gold (Au) electrode assembled with 11-Mercaptoundecanoic acid. Electrochemical impedance spectroscopy (EIS) was used to verify the stepwise assembly of the sensor system. The work conditions of the impedimetric immunosensor, such as pH of the buffer solutions and the incubation time of lectin, were optimized. Faradic impedance spectra for charge transfer for the redox probe Fe(CN)₆^3−/4−were measured to determine SRB concentrations. The diameter of the Nyquist diagram that is equal to the charge-transfer resistance (R_ct) increased with increasing SRB concentration. A linear relationship between R_ct and SRB concentration was obtained in SRB concentration range of 1.8 to 1.8 × 10⁷ cfu/ml. The variation of the SRB population during the growth process was also monitored using the impedimetric immunosensor. This approach has great potential for simple, low-cost, and time-saving monitoring of microbial populations.     

Ligandless dispersive liquid-liquid microextraction for the separation of trace amounts of silver ions in water samples and flame atomic absorption spectrometry determination

In this article, a new ligandless dispersive liquid-liquid microextraction method has been developed for preconcentration of trace quantities of silver as a prior step to its determination by flame atomic absorption spectrometry. In the proposed approach, carbon tetrachloride and ethanol were used as extraction and dispersive solvents. Several factors that may be affected on the extraction process, like, extraction solvent, disperser solvent, the volume of extraction and disperser solvent, pH of the aqueous solution and extraction time were optimized. Under the optimal conditions, the calibration curve was linear in the range of 5.0 ng mL⁻¹ to 2.0 μg mL⁻¹ of silver with R² = 0.9995 (n = 9) and detection limit based on three times the standard deviation of the blank (3S_b) was 1.2 ng mL⁻¹ in original solution. The relative standard deviation for eight replicate determination of 0.5 μg mL⁻¹ silver was ±1.5%. The high efficiency of dispersive liquid-liquid microextraction to carry out the determination of silver in complex matrices was demonstrated. The proposed method has been applied for determination of trace amount of silver in standard and water samples with satisfactory results.     

A sensitive and label-free impedimetric biosensor based on an adjunct probe

A highly sensitive and label-free impedimetric biosensor is achieved based on an adjunct probe attached nearby the capture probe. In this work, the adjunct probe was co-assembled on the surface of gold electrode with the capture probe hybridized with the reporter probe, and then 6-mercapto-1-hexanol was employed to block the nonspecific binding sites. When target DNA was added, the adjunct probe functioned as a fixer to immobilize the element of reporter probe displaced by the target DNA sequences and made the reporter probe approach the electrode surface, leading to effective inhibition of charge transfer. The increase in charge transfer resistance is related to the quantity of the target DNA in a wide range. The linear range for target DNA with specific sequences was from 0.1 nM to 0.5 μM with a good linearity (R = 0.9988) and a low detection limit of 6.3 pM. This impedimetric biosensor has the advantages of simplicity, sensitivity, good selectivity, and large dynamic range.     

A novel two-dimensional silver(I) saccharinato coordination polymer constructed from weak Ag?C interactions: Synthesis, IR spectra and X-ray structure

A new dinuclear silver(I)-saccharinato (sac) complex with acetonitrile (MeCN), [Ag₂(sac)₂(MeCN)₂]_n has been synthesized and characterized by elemental analysis, IR spectroscopy and single crystal X-ray diffraction. The silver(I) ions are doubly bridged by two sac ligands, leading to a short argentophilic contact of 2.9074(3) Å. Each silver(I) ion exhibits a square-planar coordination geometry including the Ag-Ag bonds. The individual dimeric molecules are extended into a two-dimensional layered structure by weak Ag?C_sac (η²) interactions of ca. 3.2 Å. These interactions were discussed and compared with those found in the first silver(I)-sac complex [Ag(sac)]_n.     

Structural and morphological properties of silver nanoparticles–phosphate glass composites

New types of composite materials belonging to the (100 − x) [50P₂O₅ · 30CaO · 20Na₂O]xAg₂O glasses system with 0 ? x ? 0.25 are obtained. Their local structure is analyzed with the help of Raman and infrared spectroscopy and it was found that the glasses structure is built up from predominantly ionic phosphate units. UV–VIS absorption measurements performed on the samples reveal the existence of silver nanoparticles within the soda–calcium-phosphate glass matrix. The electronic absorption spectra and TEM pictures analyses indicate the presence of silver nanoparticles of almost spherical shapes and various sizes inside the glass matrix, depending on the Ag₂O content. By using the experimental UV–VIS data and a theoretical approach important structural and morphological parameters, such as the radius of the silver nanospheres and the volume fraction of the spheres are determined for one of the investigated composites (x = 0.05 mol%).     

Crystal chemistry and crystallography of the SrR2CuO5 (R=lanthanides) phases

The crystal chemistry and crystallography of the compounds SrR₂CuO₅ (Sr-121, R=lanthanides) were investigated using the powder X-ray Rietveld refinement technique. Among the 11 compositions studied, only R=Dy and Ho formed the stable SrR₂CuO₅ phase. SrR₂CuO₅ was found to be isostructural with the “green phase”, BaR₂CuO₅. The basic structure is orthorhombic with space group Pnma. The lattice parameters for SrDyCuO₅ are a=12.08080(6) Å, b=5.60421(2) Å, c=7.12971(3) Å, V=482.705(4) Å³, and Z=8; and for the Ho analog are a=12.03727(12) Å, b=5.58947(7) Å, c=7.10169(7) Å, V=477.816(9) Å³, and Z=8. In the SrR₂CuO₅ structure, each R is surrounded by seven oxygen atoms, forming a monocapped trigonal prism (RO₇). The isolated CuO₅ group forms a distorted square pyramid. Consecutive layers of prisms are stacked in the b-direction. Bond valence calculations imply that residual strain is largely responsible for the narrow stability of the SrR₂CuO₅ phases with R=Dy and Ho only. X-ray powder reference diffraction patterns for SrDy₂CuO₅ and SrHo₂CuO₅ were determined.     

Spin solitons in organic charge-transfer salts

Organic charge-transfer (CT) salts that crystallize in face-to-face stacks of π-electron donors (D) and acceptors (A) are one-dimensional electronic systems with strong coupling to lattice and molecular vibrations. Peierls–Hubbard models of CT salts resemble π-electron theory of conjugated polymers, although transfer integrals t along mixed DA stacks are considerably smaller. Strong D and A yield Peierls systems with dimerized ground states of ion radicals, D⁺ and A⁻. Topological spin solitons separate regions of opposite dimerization, similarly to solitons in trans-polyacetylene, but are thermally accessible in ionic CT salts due to small t. Salts with still smaller t have Peierls transitions at T_P < 300 K to undimerized stacks. A Peierls–Hubbard model, H_CT, describes both types of salts and estimates of t are consistent with T_P < 300 K in some salts and spin solitons in others with higher T_P. Electron paramagnetic resonance (epr) spectra of single crystals provide direct evidence for spin solitons and one-dimensional electronic states. Spin solitons and H_CT resolve longstanding conflicts between vibrational and magnetic data that indicate dimerized stacks in several prototypical CT salts, while structural data point to undimerized stacks with large thermal ellipsoids. The low energy scale, availability of single crystals and diversity of CT salts offer opportunities for detailed modeling.     

Determination of nitrous acid in air using wet effluent diffusion denuder-FIA technique

A sensitive and fast method for the determination of nitrous acid (HONO) in air is described. The method combines a continuous collection of nitrous acid into a thin film of absorption liquid in a cylindrical wet effluent diffusion denuder (CWEDD) and on-line analysis of collected nitrous acid at the denuder concentrate employing a flow-injection analysis (FIA) where nitrous acid is oxidized into peroxynitrous acid and a chemiluminescent light emitted during the reaction of peroxynitrite with luminol is detected. Various absorption solutions (carbonate, bicarbonate, phosphate) as well as deionized water were compared from point of view of collection efficiency of nitrous acid at the CWEDD and selectivity and sensitivity of nitrous acid determination in air.All tested liquids provide quantitative collection of HONO in the CWEDD at the air flow rate of 1 L min⁻¹. The detection limit of nitrous acid of 15 ppt (v/v) is the same for all tested liquids. Small positive interference of nitrogen dioxide and peroxyacetylnitrate has been found. The lowest interference of NO₂ was found for 1 × 10⁻⁴ M NaHCO₃ (pH 6.4; 0.18%) while for deionized water interference of NO₂ (0.28%) was slightly higher. The lowest interference of peroxyacetylnitrate was found for deionized water (1.46%). No enhanced formation of HONO inside the cylindrical wet effluent diffusion denuder was observed for simultaneous bringing of nitrogen dioxide together with phenol, p-cresol, guaiacol, catechol, o-nitrophenol as well as with n-octane, n-nonane, n-decane, isoprene, α-pinene, β-pinene, camphene, 3-carene, α-phellandrene, S-limonene, benzene, toluene or o-xylene in comparison with formation of HONO only in the presence NO₂.Deionized water was chosen as the optimum absorption liquid for the sampling of atmospheric nitrous acid at the CWEDD as well as for FIA chemiluminescent detection. The time resolution is 70 s and the response time is 164 s. The calibration curve is linear over 4 orders of magnitude (0.045-450 ppb HONO). The CWEDD-FIA technique has been applied to the measurement of nitrous acid in urban air.     

Dynamic mechanical and thermal behavior of liquid-crystalline polybutadiene-diols with mesogenic groups in side chains

Liquid-crystalline polybutadiene-diols (LCPBDs) with the comb-like architecture were synthesized by reaction of a LC thiol with the double bonds of telechelic HO-terminated polybutadiene (PBD). LCPBDs with various initial molar ratios of thiol to double bonds of PBD, R₀, in the range from 0.15 to 1, were prepared by the radical reaction at temperature 60 °C for 48 h. The experimentally obtained degree of modification, R_e, after the reaction and purification, was determined from elemental analysis - from the amount of sulphur bounded in LCPBDs, GPC and from ¹H NMR spectra. The physical properties were investigated by differential scanning calorimetry and dynamic mechanical spectroscopy. With increasing R_e ratio the glass transition temperature of LCPBDs, T_g, increases from ∼ − 45 °C (neat PBD) to ∼20 °C (R_e ∼ 0.5). LC transition starts at R_e ∼ 0.27 (the transition temperature T_m ∼ 27 °C). With increasing R_e temperature T_m increases and for R_e ∼ 0.5 reaches the value T_m ∼ 74 °C; at the same time also the change in enthalpy at LC transition increases. The LC transition could be detected also by the dynamic mechanical spectroscopy; especially shape and position of mechanical functions on frequency and free volume parameters strongly depend on degree of modification.     

Transition-metal complexes of phenoxy-imine ligands modified with pendant imidazolium salts: Synthesis, characterisation and testing as ethylene polymerisation catalysts

Reaction between 3-((1R,2R)-2-{[1-(3,5-di-tert-butyl-2-hydroxy-phenyl)-meth-(E)-ylidene]-amino}-cyclohexyl)-1-isopropyl-4-phenyl-3H-imidazol-1-ium bromide (1a) or the derivative 3-((1R,2R)-2-{[1-(2-hydroxy-5-nitro-phenyl)-meth-(E)-ylidene]-amino}-cyclohexyl)-1-isopropyl-4-phenyl-3H-imidazol-1-ium bromide (1b) and metal halides MCl_x.yTHF (M = Zr, x = 4, y = 2; M = V, x = y = 3; M = Cr, x = y = 3), in THF, at −78 °C gives the metal complexes of general formula [MCl_x(κ²-N,O-OC₆H₂R¹R²C(H)N-C₆H₁₀-Im)₂][Br]₂ (where M = Zr, x = 2, R¹ = R² = ^tBu, 2; M = Zr, x = 2, R¹ = H, R² = NO₂, 3; M = V, x = 1, R¹ = R² = ^tBu, 4; M = Cr, x = 1, R¹ = R² = ^tBu, 5; M = Fe, x = 0, R¹ = R² = ^tBu, 6; Im = 1-isopropyl-4-phenyl-3H-imidazol-1-ium-3-yl). ¹H and ¹³C NMR spectroscopy of 2 and 3 indicate κ²-N,O-ligand coordination via the phenoxy-imine moiety with pendant imidazolium salt that is corroborated by a single crystal structure of 6. Compounds 2, 3, 4 and 5 were tested as precatalysts for ethylene polymerisation in the presence of methylaluminoxane (MAO) cocatalyst, showing low activity. Selected polymer samples were characterised by GPC showing multimodal molecular weight distributions.     

Ultrasound assisted ambient temperature synthesis of ternary oxide AgMO2 (M=Fe, Ga)

The application of ultrasound for the synthesis of ternary oxide AgMO₂ (M=Fe, Ga) was investigated. Crystalline α-AgFeO₂ was obtained from the alkaline solutions of silver and iron hydroxides by sonication for 40 minutes. α-AgFeO₂ was found to absorb optical radiation in the 300-600 nm range as shown by diffuse reflectance spectroscopy. The Raman spectrum of α-AgFeO₂ exhibited two bands at 345 and 638 cm⁻¹. When β-NaFeO₂ was sonicated with aqueous silver nitrate solution for 60 minutes, β-AgFeO₂ possessing orthorhombic structure was obtained as the ion-exchanged product. The Raman spectrum of β-AgFeO₂ showed four strong bands at 295, 432, 630 and 690 cm⁻¹. Sonication of β-NaGaO₂ with aqueous silver nitrate solution for 60 minutes resulted in olive green colored, α-AgGaO₂. The diffuse reflectance spectrum and the EDX analysis confirmed that the ion-exchange through sonication was complete. The Raman spectrum of α-AgGaO₂ had weak bands at 471 and 650 cm⁻¹.     

Solubility of HFCs in lower alcohols

This work is inserted in a research program that consists mainly in the experimental and theoretical study of the effect of association between solute and solvent molecules in the solubility of gases in liquids.The solubilities of hydrofluorocarbons, HFCs, (CH₃F, CH₂F₂, CHF₃) in lower alcohols (methanol, ethanol, 1-propanol, 1-butanol) have been determined in the temperature range [284, 313] K, at atmospheric pressure. An automated apparatus based on Ben-Naim-Baer and Tominaga et al. designs was used, which provides an accuracy of 0.6%. A precision of the same order of magnitude was achieved.To represent the temperature dependence of the mole fraction solubilities, the equation R ln x₂ = A + B/T + C ln T was used. From this equation, the experimental Gibbs energies, enthalpies and entropies of solution at 298 K and 1 atm partial pressure of the gas, were calculated.A semiempirical correlation has been developed between the solubilities of HFCs in alcohols at 298 K and the Gutmann acceptor number of solvents, AN, and reduced dipole moment of the gases, μ*.     

A series of new zirconium complexes bearing bis(phenoxyketimine) ligands: Synthesis, characterization and ethylene polymerization

A series of new zirconium complexes bearing bis(phenoxyketimine) ligands, bis((3,5-di-tert-butyl-C₆H₂-2-O)R₁CN (2-R₂-C₆H₄))ZrCl₂ {R₁ = Me, R₂ = H (2a); R₁ = Et, R₂ = H (2b); R₁ = Ph, R₂ = H (2c); R₁ = 2-Me-Ph, R₂ = H (2d); R₁ = 2-F-Ph, R₂ = H (2e); R₁ = 2-Cl-Ph, R₂ = H (2f); R₁ = 2-Br-Ph, R₂ = H (2g); R₁ = Ph, R₂ = Me (2h); R₁ = Ph, R₂ = F (2i)}, have been prepared, characterized and tested as catalyst precursors for ethylene polymerization. Crystal structure analysis reveals that complex 2c has a six coordinate center in a distorted octahedral geometry with trans-O, cis-N, cis-Cl arrangement which possesses approximate C₂ symmetry. When activated with methylaluminoxane (MAO), complexes 2a-2i exhibited high ethylene polymerization activities of 10⁶-10⁸ g PE (mol M h)⁻¹. Compared with the bis(phenoxyimine) zirconium analogues bis((3,5-di-tert-butyl-C₆H₂-2-O)CHNC₆H₅)ZrCl₂ (3), the introduction of substituent on the carbon atom of the imine double bond enhanced the catalytic activity and molecular weight of prepared polyethylene. Especially, when the H atom at the carbon atom of the imine double bond was replaced by 2-fluoro-phenyl with strong electronic-withdrawing property, complex 2e displayed the highest catalytic activity, and the polyethylene obtained possessed the highest molecular weight and melt point.     

Solvatochromism, hyperpolarizability, molecular and crystal structure of betaine dye 4-(2,4,6-triphenylpyridinium-1-yl)-phenolate

Solvatochromic effect of 4-(2,4,6-triphenylpyridinium-1-yl)-phenolate hydrate, 1, was determined. CT absorption band, which gave the shift from 23,880 (in water solution) to 14,440 cm⁻¹ (in anisole solution) allowed the molecular second order polarizability β_CT to be estimated as 59.5×10⁻³⁰ cm⁵ esu⁻¹. The crystal structure of 1 was determined: C₂₉H₂₁NO·5.78H₂O; orthorhombic, C222₁, a=15.005(9), b=24.356(4), c=7.5097(9) Å; V=2744.5(17) Å³, Z=4, D_X=1.224 g cm⁻¹; λ=0.71073 Å (Mo Kα); μ=0.087 mm⁻¹; final R₁=0.0551 for 2882 reflections [I>2σ(I)]. The molecules of 1, in an anti-parallel arrangement, form columns along the c-axis through stacking between the pyridinium ring and a phenyl ring in para position of the neighbouring molecule. Water molecules filling channels between the columns are disordered. Two of water molecules are connected by hydrogen bonds with negatively charged oxygen atom of 1. Powdered samples of 1 revealed only weak SHG response as measured using HRS method in relation to urea standard.     

Chemical modification of poly(n-hexylsilane) - Synthesis of functional polysilanes bearing thienyl groups on the appended sila-alkyl side chains and their application in the generation and stabilization of silver nanoparticles

The linear polysilanes [{RR′₂Si(CH₂)_ySi(n-hex)}_x{HSi(n-hex)}_1−x]_n (1-4; R = 2-thienyl, R′ = H; R = Me, R′ = 2-thienyl; y = 2, 3) have been synthesized by hydrosilylation reaction between preformed poly(n-hexylsilane) and (2-thienyl)vinyldichlorosilane/allyl(2-thienyl)dichlorosilane/bis(2-thienyl)methylvinylsilane/allyl-bis(2-thienyl)methylsilane using AIBN as the free radical initiator. GPC analysis reveals a monomodal molecular weight distribution in each case with M_w = 2492-3280 and PDI = 1.18-1.44. The polysilane 1 (R = 2-thienyl, R′ = H, y = 2) acts as reducing agent towards silver tetrafluoroborate under mild conditions (cyclohexane, rt, 5 h) to afford spherical silver nanoparticles of size 8.4 ± 0.7 nm, as evident from the TEM and dynamic light scattering (DLS) studies. The silver nanoparticles in the polymer matrix exhibit surface plasmon absorption at 420 nm suggesting the donor-acceptor interaction between the thienyl group and the metal nanocluster surface. This stabilization effect provides long shelf life stability to the nanoparticles in solution with no sign of agglomeration even after three months.     

High throughput method for the analysis of cetrizine hydrochloride in pharmaceutical formulations and in biological fluids using a tris(2,2'-bipyridyl)ruthenium(II)-peroxydisulphate chemiluminescence system in a two-chip device

A fast, economic and sensitive chemiluminescence (CL) method has been developed for the analysis of cetrizine hydrochloride (CET) in pharmaceutical formulations and in biological fluids. The CL method is based on the oxidation of tris(2,2′-bipyridyl)ruthenium(II) (Ru (bipy)₃²⁺) by peroxydisulphate in a two-chip device. Up to 180 samples can be analysed per hour, consuming only minute quantities of reagents. Three instrumental setups were tested to find the most economical, sensitive and high throughput setup. In the first setup, a continuous flow of sample and CL reagents was used, whereas in the second setup, a fixed volume (2 μL) of (Ru (bipy)₃²⁺) was introduced into a continuous infusion of peroxydisulphate and the sample. In the third design, a fixed volume of sample (2 μL) was injected while the CL reagents were continuously infused. Compared to the first setup, a 200% signal enhancement was observed in the third setup. Various parameters that influence the CL signal intensity, including pH, flow rates and reagent concentrations, were optimized. A linear response was observed over the range of 50 μg L⁻¹ to 6400 μg L⁻¹ (R² = 0.9959) with RSD values of 1.1% (n = 15) for 1000 μg L⁻¹. The detection limit was found to be 15 μg L⁻¹ (S/N = 3). The amount of consumed sample was only 2 μL, from which the detected amount of CET was found to be 6.5 × 10⁻¹⁴ mol. This procedure was successfully applied to the analysis of CET in pharmaceutical formulations and biological fluids.     

A passive sampling-based analytical strategy for the determination of volatile organic compounds in the air of working areas

An analytical methodology based on the use of a polyethylene layflat tube filled with activated carbon and Florisil (ACFL-VERAM) was employed for the passive sampling of volatile organic compounds (VOCs) in the air of working areas of packing industries. VOCs amount in the ACFL-VERAM sampler was directly determined through head-space-gas chromatography-mass spectrometry (HS-GC-MS) allowing a direct determination in only 20 min without the need of any previous treatment. Uptake parameters, like sampling rate (R_S) and sampler-air partition coefficient (K_SA), were determined for every studied VOC from adsorption isotherm data. Additionally, experimental equations have been proposed to predict R_S and K_SA from the octanol-air partition coefficients reported in the literature. The proposed methodology reaches method detection levels from 0.007 to 0.2 mg m⁻³ for the studied VOCs.     

Titanium (IV) complexes based on substituted 2-[(2-hydroxyethyl)]aminophenols

Novel substituted 2-[(2-hydroxyethyl)]aminophenols, MeN(CHR¹CR²R³OH)(C₆H₄-o-OH) (2-5), were synthesized by the reaction of 2-methylaminophenol with corresponding oxiranes. Titano-spiro-bis(ocanes) [MeN(CHR¹CR²R³O)(C₆H₄-o-O)]₂Ti 6-9 (2, 6, R¹ = H, R² = R³ = Me; 3, 7, R¹ = R² = Ph (treo-), R³ = H; 4, 8, R¹ = Ph, R² = R³ = H; 5, 9, R¹ = R² = H, R³ = Ph) based on [ONO]-ligands have been synthesized. The obtained compounds were characterized by ¹H and ¹³C NMR spectroscopy and elemental analysis data. The complex [Ti(μ²-O){O-o-C₆H₄}{μ²-CMe₂CH₂}NMe]₆ (10) was obtained by controlled hydrolysis of 6. Molecular structure of 10 was determined by X-ray structure analysis.