Comparative adsorption of methylene blue by magnetic baker’s yeast and EDTAD-modified magnetic baker’s yeast: Equilibrium and kinetic study

Magnetic baker’s yeast (MB) was prepared using glutaraldehyde cross-linking method and chemical modification with ethylenediaminetetraacetic dianhydride (EDTAD). The fabricated EDTAD-modified magnetic baker’s yeast (EMB) was then employed to remove methylene blue. Comparative adsorption of methylene blue by EMB and MB was systematically investigated with respect to pH, contact time, initial concentration and reaction temperature. The mechanism of methylene blue adsorption by EMB and MB was investigated by SEM, FTIR and Special surface area using methylene blue method. The results revealed that Fe₃O₄ nanoparticles were steadily cross-linked/incorporated with baker’s yeast biomass and the EDTA was modified on the surface of the magnetic baker’s yeast. The equilibrium adsorption data were fitted better by Langmuir isotherm, and the specific surface areas were 42.953–226.07 m²/g for MB and 94.972–499.85 m²/g for EMB, respectively. Kinetic studies suggested that the pseudo-second-order model was suitable to describe the adsorption process. Thermodynamic studies indicated that the adsorption was feasible, spontaneous and endothermic. The recovery efficiencies were above 80% by using 0.1 M HCl.     

Aggregation process of fine hematite particles suspension using xanthan gum in the presence of Fe(III)

Aggregation is an economical and widely existing method to in hematite mineral processing. In order to achieve the aggregation of hematite particles, high-efficiency agents are required. In this work, the xanthan gum (XG) and Fe³⁺ were used to explore its aggregation effect on the fine hematite particles. The settling and adsorption experiments were conducted on hematite with XG in the absence and presence of Fe³⁺. The results show that it is difficult to settle hematite with XG alone, and XG exhibits excellent performance with the mass ratio of 2/1 (XG/ FeCl₃) at pH 2–10 in the presence of Fe³⁺. Zeta potential measurements, Fourier transform infrared (FTIR), Microscope and X-ray photoelectron spectroscopy (XPS) analyses were performed to detect the underlying mechanism. The zeta potential, solution chemistry and FTIR analyses results show that the co-adsorption of XG, Fe(OH)₂⁺, Fe(OH)²⁺ and Fe³⁺ is found on hematite surface through specific and electrostatic adsorption, respectively, and the hematite surface is also covered by Fe(OH)_3(s) precipitation turned by Fe³⁺. XPS spectral investigations and microscope observations provide evidence in support of coordination interaction between ferric ions active sites and XG. In addition, the aggregation model of fine hematite particles suspension using XG in the presence of Fe³⁺ was drawn.     

基于静电喷射法活性多孔磁性炭球的制备及其对亚甲基蓝的吸附

在利用静电喷射一步法获得壳聚糖(CS)磁性微球(Fe₃O4/CS)的基础上,对Fe₃O4/CS进行高温炭化和碱活化处理获得活性磁性多孔炭球(A-Fe₃O4/C),并对A-Fe₃O4/C吸附水中亚甲基蓝(MB)分子的性能进行了研究。在利用扫描电子显微镜、红外吸收光谱仪、比表面分析仪对制备微球的形貌和结构进行分析的基础上,深入研究溶液pH、吸附时间、温度以及活化剂种类等因素对A-Fe₃O4/C吸附性能的影响。研究结果表明,A-Fe₃O4/C对MB的吸附量随着pH值的增加而增大,且经KOH活化后的A-Fe₃O4/C对MB表现出较优的吸附性能。A-Fe₃O4/C对MB的吸附过程符合伪二级动力学方程和Langmuir等温线模型,理论最大吸附容量可达300.6 mg·g^-1。此外,A-Fe₃O4/C表现出良好的重复利用性能,6次循环后对MB的去除率没有明显下降。     

基于静电喷射法活性多孔磁性炭球的制备及其对亚甲基蓝的吸附

在利用静电喷射一步法获得壳聚糖(CS)磁性微球(Fe₃O₄/CS)的基础上,对Fe₃O₄/CS进行高温炭化和碱活化处理获得活性磁性多孔炭球(A-Fe₃O₄/C),并对A-Fe₃O₄/C吸附水中亚甲基蓝(MB)分子的性能进行了研究。在利用扫描电子显微镜、红外吸收光谱仪、比表面分析仪对制备微球的形貌和结构进行分析的基础上,深入研究溶液pH、吸附时间、温度以及活化剂种类等因素对A-Fe₃O₄/C吸附性能的影响。研究结果表明,A-Fe₃O₄/C对MB的吸附量随着pH值的增加而增大,且经KOH活化后的A-Fe₃O₄/C对MB表现出较优的吸附性能。A-Fe₃O₄/C对MB的吸附过程符合伪二级动力学方程和Langmuir等温线模型,理论最大吸附容量可达300.6 mg·g^-1。此外,A-Fe₃O₄/C表现出良好的重复利用性能,6次循环后对MB的去除率没有明显下降。     

磁性壳聚糖/Fe3O4/氧化石墨烯吸附剂的制备及其多染料吸附性能

为了提高壳聚糖的多染料吸附性能并使其便于固液分离,采用共沉淀法制备了壳聚糖、磁铁矿纳米颗粒、氧化石墨烯复合磁性吸附剂(CS/Fe₃O₄/GO)。系统的结构表征显示,CS包覆的Fe₃O₄磁性纳米颗粒均匀地分布在GO的表面。CS/Fe₃O₄/GO具有高达42.5 emu·g^-1的室温铁磁性,因此可在外加磁场中实现高效固液分离。研究表明,CS/Fe₃O₄/GO对亚甲基蓝(MB)、甲基橙(MO)和刚果红(CR)等多种染料具有良好的吸附性能,溶液的pH、初始浓度和吸附时间对其多染料吸附性能具有显著影响。在最佳条件下,CS/Fe₃O₄/GO对MB、MO和CR的吸附量分别达到210.6、258.6和308.9 mg·g^-1。CS/Fe₃O₄/GO具有优异的循环利用性能,经5次循环后仍能保留90%以上的原始吸附量。采用吸附等温线和吸附动力学对CS/Fe₃O₄/GO的多染料吸附性能进行了拟合分析,并详细讨论了其吸附机理。     

A comparative DFT study of Fe3+ and Fe2+ ions adsorption on (100) and (110) surfaces of pyrite: An electrochemical point of view

Pyrite acts as a catalyst in the mineral processing, and the speed of ferric ion reduction and mineral decomposition increases with increasing cathodic points. In this study, the ferric ion interaction on the (100) and (110) surfaces of pyrite was studied using the density functional theory calculations. The analysis of stability, density of states, and electron density were performed to understand the interaction between the ferric ion and pyrite surfaces. The results showed that pyrite surface is chemically active and tends to absorb ferric ion between two surface sulfur atoms. The hyperconjugation between the 3d orbital of ferric ion and the 3p or 3d orbitals of surface atoms provides the conditions for the Fe³⁺ ion adsorption. The molecular orbital (MO) and electron density analyses indicate that the 3p orbitals of S atoms play a more important role in bonds formations relative to the 3d orbitals. The (110) surface is more active, and the adsorption energy is larger than that of surface (100), which is the result of decreased cation coordination and the presence of sulfur at the surface. Subsequently, the interaction of the Fe²⁺ ion, as product of Fe³⁺ ion reduction and its competitor for adsorption, on the surfaces was studied. The Fe^{2 +} ion adsorbs stronger at the surface of (110), and the adsorption energies at (100) and (110) surfaces were obtained as −24 and −47 kcal/mol, respectively. In general, the Fe³⁺ ion is a stronger oxidizing agent than Fe²⁺ on pyrite surfaces.     

磁性壳聚糖/Fe3O4/氧化石墨烯吸附剂的制备及其多染料吸附性能

为了提高壳聚糖的多染料吸附性能并使其便于固液分离,采用共沉淀法制备了壳聚糖、磁铁矿纳米颗粒、氧化石墨烯复合磁性吸附剂(CS/Fe₃O₄/GO)。系统的结构表征显示,CS包覆的Fe₃O₄磁性纳米颗粒均匀地分布在GO的表面。CS/Fe₃O₄/GO具有高达42.5 emu·g-1的室温铁磁性,因此可在外加磁场中实现高效固液分离。研究表明,CS/Fe₃O₄/GO对亚甲基蓝(MB)、甲基橙(MO)和刚果红(CR)等多种染料具有良好的吸附性能,溶液的pH、初始浓度和吸附时间对其多染料吸附性能具有显著影响。在最佳条件下,CS/Fe₃O₄/GO对MB、MO和CR的吸附量分别达到210.6、258.6和308.9 mg·g-1。CS/Fe₃O₄/GO具有优异的循环利用性能,经5次循环后仍能保留90%以上的原始吸附量。采用吸附等温线和吸附动力学对...     

Photocatalytic degradation of organic compounds in aqueous systems by Fe and Ho codoped TiO<Subscript>2</Subscript>

Undoped, single-doped, and codoped TiO₂ nanoparticles were prepared by the sol-gel method and characterized with X-ray diffraction (XRD), the Brunauer-Emmett-Teller (BET)-specific surface area (S_BET), UV-Vis absorption spectra (UV-Vis), and X-ray photoelectron spectroscopy (XPS). Their photocatalytic activity was evaluated by methyl orange (MO) degradation in an aqueous suspension under UV or simulated solar light illumination. XRD showed that all samples calcined at 600°C preserved the anatase structure, and doping inhibited the increase of crystallite size. The BET result revealed that doping improved the surface area of TiO₂. UV-Vis indicated that Fe³⁺-doping broadened the absorption profile of TiO₂. XPS demonstrated that doping was advantageous to absorb more surface hydroxyl groups or chemisorbed water molecules. Photocatalytic degradation showed that the photocatalytic activity of TiO₂ codoped with Fe³⁺ and Ho³⁺ ions was markedly improved. This was ascribed to the fact that there was a cooperative action in the two doped elements. Fe³⁺-doping broadens the absorption profile, improves photo utilization of TiO₂, and then generates more electronhole pairs. Ho³⁺-doping restrains the increase in grain size and retards the recombination of photo-generated electrons and holes.     

Preparation of Bamboo-Based Hierarchical Porous Carbon Modulated by FeCl3 towards Efficient Copper Adsorption

Using bamboo powder biochar as raw material, high-quality meso/microporous controlled hierarchical porous carbon was prepared—through the catalysis of Fe³⁺ ions loading, in addition to a chemical activation method—and then used to adsorb copper ions in an aqueous solution. The preparation process mainly included two steps: load-alkali leaching and chemical activation. The porosity characteristics (specific surface area and mesopore ratio) were controlled by changing the K₂CO₃ impregnation ratio, activation temperature, and Fe³⁺ ions loading during the activation process. Additionally, three FBPC samples with different pore structures and characteristics were studied for copper adsorption. The results indicate that the adsorption performance of the bamboo powder biochar FBPC material was greatly affected by the meso/micropore ratio. FBPC _2.5-900-2%, impregnated at a K₂CO₃: biochar ratio of 2.5 and a Fe³⁺: biochar mass ratio of 2%, and activated at 900 °C for 2 h in N₂ atmosphere, has a very high specific surface area of 1996 m² g⁻¹ with a 58.1% mesoporous ratio. Moreover, it exhibits an excellent adsorption capacity of 256 mg g⁻¹ and rapid adsorption kinetics for copper ions. The experimental results show that it is feasible to control the hierarchical pore structure of bamboo biochar-derived carbons as a high-performance adsorbent to remove copper ions from water.     

Facile synthesis of magnetic hybrid metal–organic frameworks with high adsorption capacity for methylene blue

A magnetic hybrid material (Fe₃O₄‐COOH/HKUST‐1) was easily synthesized via a two‐step simple solvothermal method. Through adding sodium acrylate directly into the synthesis of Fe₃O₄ spheres, the surface has more carboxyl groups. It is notable that the reactions proceed without use of organic surfactants. The magnetic hybrid material was characterized using various techniques. The magnetic hybrid material has a high specific surface area (430.15 m² g⁻¹) and excellent magnetism (23.65 emu g⁻¹). It is an efficient adsorbent for removing organic dyes like methylene blue (MB) from aqueous solution. It also can be easily recovered from liquid media using an external magnetic field. Adsorption experiment shows the magnetic hybrid material possesses a high adsorption capacity (118.6 mg g⁻¹), and has high adsorption efficiency (94.3%) after five adsorption cycles with ethanol (0.2% HCl) as eluent. The sorption kinetics and isotherm analysis indicate these sorption processes are better fitted to the pseudo‐second‐order and Langmuir equations. Thermodynamic study shows the sorption processes are spontaneous and endothermic.     

Highly efficient adsorption of Cr(VI) from aqueous solution by Fe3+ impregnated biochar

Biochar (BC) has been widely used as a low-cost adsorbent for the removal of contaminants from water and soil. However, the adsorption ability of BC towards heavy metal oxyanions (e.g., Cr(VI)) is relatively low due to the negatively charged surface of BC. In this study, pristine BC was impregnated with Fe³⁺ to improve its Cr(VI) adsorption capability. Fe³⁺-impregnated BC (Fe³⁺-BC) was successfully synthesized by a simple impregnation method and used for the removal of Cr(VI) from aqueous solution. Various factors affecting the adsorption, such as impregnation ratio, pH, adsorbent dosage, contact time, temperature, and the presence of humic acid, were investigated in detail. Results showed that Fe³⁺-BC had strong adsorption ability to Cr(VI) with a maximum adsorption capacity of 197.80 mg/g, which were not only significantly higher than that of the pristine BC, but also were superior to many previously reported adsorbents. It was favorable for Cr(VI) adsorption under the condition of acidic and high temperature. The adsorption data obeyed Sips and Langmuir isotherms and the kinetic data were well described by the pseudo-first-order kinetic model. The results herein revealed that the Fe³⁺-impregnated BC had a good potential as a highly efficient material for adsorption of Cr(VI) from aqueous solution.     

Equilibrium and kinetic study of novel methyltrimethoxysilane magnetic titanium dioxide nanocomposite for methylene blue adsorption from aqueous media

Novel magnetic titanium dioxide nanoparticles decorated with methyltrimethoxysilane (Fe₃O₄@TiO₂‐MTMOS) were successfully fabricated via a sol–gel method at room temperature. The synthesized material was characterized using Fourier transform infrared spectroscopy, X‐ray diffraction, scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, thermogravimetric analysis and vibrating sample magnetometry. The removal efficiency of the adsorbent was evaluated through the adsorption of methylene blue (MB) dye from water samples. The adsorption isotherm and kinetics were evaluated using various models. The Langmuir model indicated a high adsorption capacity (11.5 mg g^?1) of Fe₃O₄@TiO₂‐MTMOS. The nanocomposite exhibited high removal efficiency (96%) and good regeneration (10 times) compared to Fe₃O₄ and Fe₃O₄@TiO₂ at pH = 9.0. Based on the adsorption mechanism, electrostatic interaction plays a main role in adsorption since MB dye is cationic in nature at pH = 9, whereas the adsorbent acquired an anionic nature. The newly synthesized Fe₃O₄@TiO₂‐MTMOS can be used as a promising material for efficient removal of MB dye from aqueous media.     

Green one‐pot preparation of α‐Fe2O3@carboxyl‐functionalized yeast composite with high adsorption and catalysis properties for removal of methylene blue

Herein, the α‐Fe₂O₃@carboxyl‐functionalized yeast composite (α‐F@CFYC) was synthesized by direct oxidation of yeast with K₂FeO₄ and used as a novel adsorbent/heterogeneous Fenton catalyst for removal of methylene blue (MB). The obtained α‐F@CFYC was fully characterized by scanning electron microscopy, EDX, X‐ray diffraction analysis, Fourier‐transform infrared, thermogravimetry, and X‐ray photoelectron spectroscopy, respectively, and the corresponding results showed that α‐Fe₂O₃ nanoparticles were successfully obtained and deposited on yeast surface, as well as more functional groups were introduced/exposed on yeast surface. Furthermore, various influence parameters (eg, contact time, initial pH, and MB concentration) on the adsorption/catalysis ability of α‐F@CFYC for MB have been investigated in detail under ambient conditions. As a result, owing to the synergetic effect of the loaded α‐Fe₂O₃ and the introduced/exposed functional groups on yeast surface, the as‐obtained α‐F@CFYC exhibited high adsorption capacities and good catalysis degradation properties for MB.     

The adsorption of dopamine on gold and its interactions with iron(III) ions studied by microcantilevers

The adsorption of dopamine (DA) molecules on gold and their interactions with Fe³⁺ were studied by a microcantilever in a flow cell. The microcantilever bent toward the Au side with the adsorption of DA due to the change of surface stress induced by the intermolecular hydrogen bonds of DA or the charge transfer effect between adsorbates and the substrate. The interaction process between DA adsorbates and Fe³⁺ was revealed by the deflection curves of microcantilever. As indicated by the appearance of a variation during the decline of curves, two steps were observed in the curve at relative high concentrations of Fe³⁺. In this case, Fe³⁺ reacted with DA molecules only in the outer layers and the complexes removed with solution. Then Fe³⁺ reacted further with DA molecules forming the surface complex in the first layer next to the gold. At this stage, the stability of surface complexes was time dependent, i.e., unstable initially and stable finally. This may be due to the surface complexes change from mono-dentate to bi-dentate complexes. In another case, i.e., at relative low concentration of Fe³⁺, only the first step was observed as indicated by the absence of a variation. X-ray photoelectron spectroscopy (XPS) and cycling voltammetry (CV) results provided complementary evidence for the result of microcantilever and proposal. As low as 5 × 10⁻¹⁰ M Fe³⁺ was detected by DA modified microcantilever with a good selectivity over other common metal ions.     

The Use of High Surface Area Mesoporous-Activated Carbon from Longan Seed Biomass for Increasing Capacity and Kinetics of Methylene Blue Adsorption from Aqueous Solution

Microporous- and mesoporous-activated carbons were produced from longan seed biomass through physical activation with CO₂ under the same activation conditions of time and temperature. The specially prepared mesoporous carbon showed the maximum porous properties with the specific surface area of 1773 m²/g and mesopore volume of 0.474 cm³/g which accounts for 44.1% of the total pore volume. These activated carbons were utilized as porous adsorbents for the removal of methylene blue (MB) from an aqueous solution and their effectiveness was evaluated for both the adsorption kinetics and capacity. The adsorption kinetic data of MB were analyzed by the pseudo-first-order model, the pseudo-second-order model, and the pore-diffusion model equations. It was found that the adsorption kinetic behavior for all carbons tested was best described by the pseudo-second-order model. The effective pore diffusivity (D_e) derived from the pore-diffusion model had the values of 4.657 × 10⁻⁷–6.014 × 10⁻⁷ cm²/s and 4.668 × 10⁻⁷–19.920 × 10⁻⁷ cm²/s for the microporous- and mesoporous-activated carbons, respectively. Three well-known adsorption models, namely the Langmuir, Freundlich and Redlich–Peterson equations were tested with the experimental MB adsorption isotherms, and the results showed that the Redlich–Peterson model provided the overall best fitting of the isotherm data. In addition, the maximum capacity for MB adsorption of 1000 mg/g was achieved with the mesoporous carbon having the largest surface area and pore volume. The initial pH of MB solution had virtually no effect on the adsorption capacity and removal efficiency of the methylene blue dye. Increasing temperature over the range from 35 to 55 °C increased the adsorption of methylene blue, presumably caused by the increase in the diffusion rate of methylene blue to the adsorption sites that could promote the interaction frequency between the adsorbent surface and the adsorbate molecules. Overall, the high surface area mesoporous carbon was superior to the microporous carbon in view of the adsorption kinetics and capacity, when both carbons were used for the removal of MB from an aqueous solution.     

Interactions and Analysis of Diethyl-S (Ethyl-Thiomethyl)-Phosphorothiolothionate

Abstract

In this paper are presented some of interactions of the diethyl-S-(ethyl-thiomethyl)-phosphorothiolothionate with Fe³⁺, Cr³⁺, Ni²⁺ and Zn²⁺ -ions. There were investigated processes of the complexation by means of UV spectrophotometry. Also was followed the differency of concentration of the investigated compound (DEETMPTT), before and after complexation, and adsorption. The cleavage reaction were studied on activated silica -air gel, by means of IR spectrophotometry.     

The fabrication of a nanoscale polyoxometalate based magnetic adsorbent and its selective adsorption on cationic dyes

Amino group-functionalized Fe₃O₄ is loaded on a coordination complex-modified polyoxometalate nanoparticle. In this composite material, Fe₃O₄ and coordination complex-modified polyoxometalate are connected with intense hydrogen bonds as suggested by FTIR. This composite material exhibits excellent methylene blue (MB) adsorption, with adsorption capacity of 175.5 mg g^?1. It also possesses selective separation ability between cationic and anionic dye molecules. In binary solution of MB and methyl orange (MO), MB adsorption efficiency reaches 75%, but it exhibits almost no effect on the adsorption of methyl orange. The saturation magnetization value of this composite material is 18.89 emu g^?1, allowing magnetic separation, which facilitates the recycle and reuse of this composite adsorbent.     

Synthesis of Porous Material from Coal Gasification Fine Slag Residual Carbon and Its Application in Removal of Methylene Blue

A large amount of coal gasification slag is produced every year in China. However, most of the current disposal is into landfills, which causes serious harm to the environment. In this research, coal gasification fine slag residual carbon porous material (GFSA) was prepared using gasification fine slag foam flotation obtained carbon residue (GFSF) as raw material and an adsorbent to carry out an adsorption test on waste liquid containing methylene blue (MB). The effects of activation parameters (GFSF/KOH ratio mass ratio, activation temperature, and activation time) on the cation exchange capacity (CEC) of GFSA were investigated. The total specific surface area and pore volume of GSFA with the highest CEC were 574.02 m²/g and 0.467 cm³/g, respectively. The degree of pore formation had an important effect on CEC. The maximum adsorption capacity of GFSA on MB was 19.18 mg/g in the MB adsorption test. The effects of pH, adsorption time, amount of adsorbent, and initial MB concentration on adsorption efficiency were studied. Langmuir isotherm and quasi second-order kinetic model have a good fitting effect on the adsorption isotherm and kinetic model of MB.     

Investigations for Modification of Polyacrylamide-Bentonite by Phytic Acid and its Usability in Fe3+, Zn2+ and UO2 2+ Adsorption

Composite of polyacrylamide-bentonite (PAA-B) was prepared by direct polymerisation of PAA in a suspension of bentonite (B). Adsorption and thermodynamic features of phytic acid (Phy) adsorption onto B, PAA and PAA-B, and those of Fe³⁺, Zn²⁺, UO₂ ²⁺ adsorption onto PAA-B and its modification by Phy (PAA-B-Phy) have been investigated. The reusability, storagability, ion selectivity and recoverability of sorbed ions with 1 M HCl have also been considered.The chemical and physical structure of adsorbents has been characterised by means of FT-IR and XRD. All adsorption isotherms for Phy and the ions were L-type of the Giles classification except, the one which is S type for adsorption of Phy onto PAA. The maximum adsorption capacities for the ions adsorbed were in order of UO₂ ²⁺ > Fe³⁺ > Zn²⁺ for PAA-B and Zn²⁺ > Fe³⁺ > UO₂ ²⁺ for PAA-B-Phy. Langmuir equilibrium constants for the adsorption of ions onto PAA-B-Phy were significantly higher than those found for PAA-B; the magnitude of increase for UO₂ ²⁺ was about 100. The thermodynamic parameters indicated that adsorption reactions are spontaneous in terms of adsorption free enthalpy.The chemical structure of PAA-B-Phy was not changed at the end of the studies of reusability and storagability. The composite was selective for UO₂ ²⁺ of the ions of interest.The composite of PAA-B and its modification by Phy have been used for the first time in this investigation. It is proposed that the composites can be practically used in the investigations and applications of adsorption.     

Study on the controllable synthesis of SH-MCM-41 mesoporous materials and their adsorption properties of the La3+, Gd3+ and Yb3+

Sulfhydryl MCM-41 (SH-MCM-41) mesoporous materials were prepared via a hydrothermal method, and -SH was successfully imported by a post-grafting method. The structure and surface properties of the materials were characterized using Fourier Transform infrared spectroscopy, X-ray diffraction and Transmission Electron Microscopy analysis. The low concentrations of La³⁺, Gd³⁺ and Yb³⁺ adsorption on the material were investigated. This paper discusses the effects of system factors, such as pH and the solid-liquid ratio, on the performance of the adsorption process. The adsorption thermodynamics and kinetics were also explored. Experimental results indicated that the materials were in good order and had high specific surface area (956 m²/g) with an average pore diameter of 2.1 nm; the mercapto groups were successfully grafted onto a molecular sieve, and the best grafted amount was 1.46 × 10^?3 mol/g. The materials showed preferable adsorption of La³⁺, Gd³⁺ and Yb³⁺ with maximum adsorption capacities of 560.56 mg/g, 467.60 mg/g and 540.68 mg/g, respectively. The adsorption process can be described by the Freundlich isotherm model, and the adsorption data fits pseudo-second-order kinetics. After repeating the elution-regeneration cycle four times, the adsorption capacity of rare earth ions was mostly maintained, indicating that the adsorbent can be regenerated well and recycled to save costs. It has potential in practical application.