溶胶-凝胶法制备纳米Pb(Zr0.52Ti0.48)O3

溶胶-凝胶法;纳米晶;溶胶-凝胶法制备纳米Pb(Zr0.52Ti0.48)O3     

不同方法制备Ni-WO_3/TiO_2-ZrO_2催化剂及其性能研究

考察了Ti O2-Zr O2载体制备方法对Ni-WO3/Ti O2-Zr O2催化正庚烷异构化反应性能的影响.通过BET、XRD、SEM和NH3-TPD的表征结果表明,以模板-溶胶-凝胶法制备Ti O2-Zr O2载体时,Ni-WO3/Ti O2-Zr O2催化剂晶相结晶度较好,具有较适宜的表面酸性和比表面积,从而在正庚烷异构化反应中表现出较高的催化活性和选择性,正庚烷的转化率和异庚烷的选择性分别为72.62%和80.81%.实验结果还表明,Ti O2-Zr O2比Zr O2、Si O2-Zr O2和Al2O3-Zr O2更适宜作为载体制备催化剂应用于正庚烷异构化的反应中.     

氮掺杂二氧化钛薄膜的光催化性能研究

采用溶胶-凝胶法制备了氮掺杂Ti O2薄膜;利用X射线光电子能谱仪、紫外-可见光谱仪表征了所制备的薄膜的化学状态和光吸收性能;并考察了可见光照射下薄膜的亲水性能和光催化性能.结果表明:N通过取代部分O的方式进入到Ti O2薄膜中,且掺杂后在可见光区的光吸收增强;最优条件下,Ti O2-xNx薄膜的接触角由31°降到12°,亲水化速度常数为0.018,可见光照射3 h,亚甲基蓝的降解率达到45%.     

制备方法对CuO—Ce0．7Zr0．3O2催化剂的氧缺位和CO氧化活性的影响

采用溶胶-凝胶法和溶胶-凝胶 浸渍法两种方法制备了CuO-Ce0.7Zr0.3O2催化剂,并对催化剂进行了XRD、Raman等表征,考察了催化剂的CO氧化性能.研究结果表明,溶胶-凝胶法制备的CuO-Ce0.7Zr0.3O2催化剂的CO氧化活性明显高于溶胶-凝胶 浸渍法制备的CuO/Ce0.7Zr0.3O2催化剂,CuO-Ce0.7Zr0.3O2催化剂容易形成氧缺位和表面高分散CuO的颗粒较大,从而提高催化活性.     

溶胶-凝胶法制备用于CO2气氛下乙苯脱氢反应的高活性Cr2O3-SiO2催化剂

 采用溶胶-凝胶法制备了Cr2O3-SiO2催化剂，考察了催化剂对CO2气氛下乙苯脱氢制苯乙烯反应的催化性能. 结果表明，溶胶-凝胶法制备的Cr2O3-SiO2催化剂上乙苯脱氢活性是常规的Cr2O3/SiO2负载型催化剂的2倍，Cr2O3-SiO2催化剂中Cr6+的含量较高是其具有高活性的主要原因.     

块状石英纤维/Al_2O_3气凝胶复合材料的非超临界干燥法制备及表征

采用溶胶-凝胶法和常压干燥法以N,N′-二甲基甲酰胺(DMF)作为干燥控制化学添加剂制备了低密度石英纤维增强Al2O3气凝胶复合材料.通过氮气吸附-脱附实验比较研究了石英纤维对氧化铝气凝胶孔结构参数的影响;采用X射线衍射技术表征了在升温过程中石英纤维/Al2O3气凝胶复合材料的相结构变化;利用扫描电子显微镜和透射电子显微镜观察了Al2O3气凝胶基体及其石英纤维复合材料的微观形貌;初步探讨了DMF对Al2O3气凝胶形貌和密度的影响.研究结果表明石英纤维/Al2O3气凝胶复合材料成块性好,纤维与气凝胶基体结合紧密,石英纤维提高了Al2O3相转变温度,适量的DMF有利于形成均匀凝胶网络结构,减小干燥收缩压力.     

Na2O掺杂C12A7材料的结构及其抗菌性能

本文利用溶胶-凝胶方法制备了Na2O掺杂的C12A7(12CaO.7Al2O3-Na2O)材料,通过X-射线衍射(XRD)、电子顺磁共振(EPR)、电感等离子体耦合-原子发射光谱(ICP-AES)和飞行时间质谱(TOF-MS)研究了材料结构与性能。选用金黄色葡萄球菌和大肠杆菌为受试菌种,研究了C12A7-Na2O的抗菌性能。结果表明,Na2O掺杂对C12A7的晶体结构以及材料中的氧负离子的浓度没有显著的影响,且C12A7-Na2O材料具有较高的抗菌性能。利用扫描电镜(SEM)对杀菌前后的金黄色葡萄球菌和大肠杆菌的菌体形态进行了观测,初步探讨了C12A7-Na2O的抗菌机理。     

掺铕Y2O3发光薄膜的制备及发光性能

溶胶-凝胶法;荧光;掺铕Y2O3发光薄膜的制备及发光性能     

复合溶胶-凝胶法改善PBO纤维的光稳定性

分别以钛酸正丁酯(C16H36O4Ti)、醋酸(CH3COOH)、盐酸(HCl)、丙基三甲氧基硅烷(KH560)、苯基三甲氧基硅烷(Ph-TMS)、甲醇(CH3OH)和去离子水(H2O)为原料,氨水(NH3·H2O)为催化剂,分别采用溶胶-凝胶法和复合溶胶-凝胶法涂覆制备防老化聚亚苯基苯并二唑(PBO)纤维。通过粒度分析验证了纳米溶胶的成功制备,通过EDS能谱、SEM扫描电镜、接触角测定等分析测试PBO纤维表面的化学组成与物理性能,验证防老化PBO纤维的成功制备。以拉伸强度测试、SEM扫描电镜和表面接触角表征PBO纤维的防老化性能。结果表明:在氙灯耐气候试验箱经历130h的老化后,与未经过涂覆的PBO原纤相比,采用纳米TiO2水溶胶-凝胶法涂覆的PBO纤维拉伸强度保持率只提高了5%,利用纳米有机硅溶胶-凝胶法涂覆的PBO纤维拉伸强度保持率可提高10%,而经过纳米TiO2和有机硅溶胶-凝胶法涂覆的PBO纤维,拉伸强度保持率提高了27%,且老化后的纤维表面保持得非常完整。     

Al2O3-PLOT毛细管色谱柱的溶胶-凝胶法制备

首次将溶胶-凝胶法用于制备Al2O3-PLOT毛细管色谱柱.采用正硅酸乙酯、稀盐酸以及氧化铝的乙醇悬浮液组成的溶胶体系,高压动态法涂敷石英毛细管,然后通过高温凝胶反应固定Al2O3涂层,再用无机盐溶液淋洗灭活得到成品.考察制备过程的重复性,表明溶胶-凝胶法制备Al2O3-PLOT色谱柱简单易行,重复性好;对色谱柱性能进行评价,18组分C1 ～C5烃类标准气完全基线分离,环丙烷和丙烯的分离度为1.55 ～1.65,甲烷和正丁烷保留时间变化范围分别小于0.5%和1%,色谱柱的耐温性和稳定性显著提高.     

锂离子蓄电池正极材料LiNi0.8 Co0.2 O2的制备及其电化学性能

用高温固相反应和氧化还原溶胶凝胶法制备了锂离子电池正极材料LiNi0.8Co0.2O2,并对其进行了电化学性能考察。结果显示,氧化还原溶胶凝胶法制备的锂离子电池正极材料的综合性能较高温固相法好。     

Electrochemical performance of sol-gel-made Na2Ti3O7 anode material for Na-ion batteries

Journal of Solid State Electrochemistry - Nanocrystalline Na2Ti3O7 material is prepared by a newly developed sol-gel procedure. The sol-gel made Na2Ti3O7 calcined at 500 °C possesses...     

Hydrothermal synthesis and characterization of nanorods of various titanates and titanium dioxide

The formation process of titania based nanorods during hydrothermal synthesis starting from an amorphous TiO2.nH2O gel has been investigated. Sodium tri-titanate (Na2Ti3O7) particles with a rodlike morphology were prepared by a simple hydrothermal process in the presence of a concentrated NaOH aqueous solution. The ion exchange reaction of the synthesized Na2Ti3O7 nanorods with HCl under ultrasonic treatment promotes a complete sodium substitution and the formation of H2Ti3O7 nanorods. Low-temperature annealing of the as-produced nanorods of Na2Ti3O7 and H2Ti3O7 leads to a loss of the layered crystal structure and the formation of nanorods of condensed framework phases-sodium hexa-titanate (Na2Ti6O13) and metastable TiO2-B phases, respectively. These transformations proceed without a significant change in particle morphology. The nanostructures were investigated by scanning electron microscopy (SEM), powder X-ray diffraction (XRD), the Brunauer-Emmett-Teller (BET) method, thermogravimetric analysis (TGA), and Raman spectroscopy. The structural defects of the synthesized nanorods were investigated by high-resolution electron microscopy. The presence of planar defects can be attributed to the exfoliation of the zigzag ribbon layers into two-dimensional titanates as well as to the condensation of the layers of TiO6 octahedra into three-dimensional frameworks.     

Full structural and electrochemical characterization of Li2Ti6O13 as anode for Li-ion batteries

A detailed structural and electrochemical study of the ion exchanged Li(2)Ti(6)O(13) titanate as a new anode for Li-ion batteries is presented. Subtle structural differences between the parent Na(2)Ti(6)O(13), where Na is in an eightfold coordinated site, and the Li-derivative, where Li is fourfold coordinated, determine important differences in the electrochemical behaviour. While the Li insertion in Na(2)Ti(6)O(13) proceeds reversibly the reaction of lithium with Li(2)Ti(6)O(13) is accompanied by an irreversible phase transformation after the first discharge. Interestingly, this new phase undergoes reversible Li insertion reaction developing a capacity of 170 mAh g(-1) at an average voltage of 1.7 V vs. Li(+)/Li. Compared with other titanates this result is promising to develop a new anode material for lithium ion rechargeable batteries. Neutron powder diffraction revealed that Na in Na(2)Ti(6)O(13) and Li in Li(2)Ti(6)O(13) obtained by Na/Li ion exchange at 325 °C occupy different tunnel sites within the basically same (Ti(6)O(13))(2-) framework. On the other hand, electrochemical performance of Li(2)Ti(6)O(13) itself and the phase released after the first full discharge is strongly affected by the synthesis temperature. For example, heating Li(2)Ti(6)O(13) at 350 °C produces a drastic decrease of the reversible capacity of the phase obtained after full discharge, from 170 mAh g(-1) to ca. 90 mAh g(-1). This latter value has been reported for Li(2)Ti(6)O(13) prepared by ion exchange at higher temperature.     

High temperature X-ray diffraction study of the formation of Na2Ti3O7 from a mixture of sodium carbonate and titanium oxide

Na2Ti3O7 has attracted much attention in the field of anode materials for Na-ion batteries thanks to its non-toxicity and very low working potential of 0.3 V vs Na0/Na+.Building a clearer picture of its formation from cheap Na₂CO₃ and TiO₂ starting materials is therefore of obvious interest.Here,we report new insights from an in-situ high temperature X-ray diffraction study conducted from room temperature to 800°C,complemented by ex-situ characterizations.We were thereby able to position the previously reported Na₄Ti₅O₁₂ and Na₂Ti₆O₁₃ intermediate phases in a reaction scheme involving three successive steps and temperature ranges.Shifts and/or broadening of a subset of the Na₂Ti₆O₁₃ reflections suggested a combination of intra-layer disorder with the well-established ordering of successive layers.This in-situ study was carried out on reproducible mixtures of Na₂CO₃ and TiO₂ in 1:3 molar ratio prepared by spraydrying of mixed aqueous suspensions.Single-phase Na₂Ti₃O₇ was obtained after only 8 h at 800°C in air,instead of a minimum of 20 h for a conventional solid-state route using the same precursors.Microstructure analysis revealed~15 mm diameter granules made up from rectangular rods of a fewmm length presenting electrochemical properties in line with expectations.In the absence of grinding or formation of intimate composites with conductive carbon,the specific capacity of 137 m Ah/g at C/5 decreased at higher rates.     

染料敏化太阳能电池对电极La2Mo2O7复合MWCNTs非Pt催化剂的制备与性能

通过高温固相法对醋酸镧（C₆H₉O₆La·xH₂O）与高钼酸铵（（NH₄）₆Mo₇O₂₄·4H₂O）在一定条件下热解制备非Pt催化剂La₂Mo₂O₇（La₂O₃-2MoO₂）。进一步采用2种方法将La₂Mo₂O₇与多壁碳纳米管（MWCNTs）进行复合,一种是将La₂Mo₂O₇喷涂到MWCNTs表层之上得到La₂Mo₂O₇/MWCNTs,另一种是将两者均匀混合掺杂得到La₂Mo₂O₇@MWCNTs,再将上述2种复合材料应用于染料敏化太阳能电池对电极进行相应研究。通过扫描电子显微镜（SEM）表征了复合催化材料的微观形貌,X射线衍射（XRD）确定了微观结构。采用电流密度-光电压曲线、循环伏安,交流阻抗以及塔菲尔极化分析了材料的光电性能。实验结果表明在电解液I₃^-/I^-中,基于La₂Mo₂O₇/MWCNTs与La₂Mo₂O₇@MWCNTs的对电极,相同的条件下在光电池中获得的光电转换效率分别为6.09%和4.84%,明显高于MWCNTs的3.94%和La₂Mo₂O₇的0.87%。电极性能的提高可归因于La₂Mo₂O₇复合催化剂相对大的比表面积和高导电性。     

染料敏化太阳能电池对电极La2Mo2O7复合MWCNTs非Pt催化剂的制备与性能

通过高温固相法对醋酸镧（C₆H₉O₆La·xH₂O）与高钼酸铵（（NH₄）₆Mo₇O₂₄·4H₂O）在一定条件下热解制备非Pt催化剂La₂Mo₂O₇（La₂O₃-2MoO₂）。进一步采用2种方法将La₂Mo₂O₇与多壁碳纳米管（MWCNTs）进行复合,一种是将La₂Mo₂O₇喷涂到MWCNTs表层之上得到La₂Mo₂O₇/MWCNTs,另一种是将两者均匀混合掺杂得到La₂Mo₂O₇@MWCNTs,再将上述2种复合材料应用于染料敏化太阳能电池对电极进行相应研究。通过扫描电子显微镜（SEM）表征了复合催化材料的微观形貌,X射线衍射（XRD）确定了微观结构。采用电流密度-光电压曲线、循环伏安,交流阻抗以及塔菲尔极化分析了材料的光电性能。实验结果表明在电解液I₃^-/I^-中,基于La₂Mo₂O₇/MWCNTs与La₂Mo₂O₇@MWCNTs的对电极,相同的条件下在光电池中获得的光电转换效率分别为6.09%和4.84%,明显高于MWCNTs的3.94%和La₂Mo₂O₇的0.87%。电极性能的提高可归因于La₂Mo₂O₇复合催化剂相对大的比表面积和高导电性。     

Ti, Na与O2反应机理的理论研究

基于MP2/6-311+G(d)水平, 分别对过渡金属Ti和碱金属Na与O2的反应机理进行了研究. 比较了Ti和Na分别以垂直O—O键和沿着O—O键的方向逼近O2, 以及中性体系Ti/Na+O2和带1个负电荷的体系(Ti/Na+O2)-的情况. 详细分析了不同反应路径的结合能和电荷变化的曲线, 预测了最佳反应方式. 结果表明, 垂直接近方式要比水平接近方式更具有优势; 体系带一个负电荷(Ti/Na+O2)-有利于金属与O2的结合. 同时, 计算结果表明在Ti+O2和(Ti+O2)-体系中Ti容易与单态的O2结合; 在中性体系中Na也容易与单态O2结合, 而在(Na+O2)-体系中Na与三态O2的结合更稳定. 在CCSD(T)/6-311++G(3df)//MP2/6-311+G(d)水平下, 计算了Ti+O2和(Ti+O2)-的反应势能面.     

Rutile-TiO2 nanocoating for a high-rate Li4Ti5O12 anode of a lithium-ion battery

Well-defined Li(4)Ti(5)O(12) nanosheets terminated with rutile-TiO(2) at the edges were synthesized by a facile solution-based method and revealed directly at atomic resolution by an advanced spherical aberration imaging technique. The rutile-TiO(2) terminated Li(4)Ti(5)O(12) nanosheets show much improved rate capability and specific capacity compared with pure Li(4)Ti(5)O(12) nanosheets when used as anode materials for lithium ion batteries. The results here give clear evidence of the utility of rutile-TiO(2) as a carbon-free coating layer to improve the kinetics of Li(4)Ti(5)O(12) toward fast lithium insertion/extraction. The carbon-free nanocoating of rutile-TiO(2) is highly effective in improving the electrochemical properties of Li(4)Ti(5)O(12), promising advanced batteries with high volumetric energy density, high surface stability, and long cycle life compared with the commonly used carbon nanocoating in electrode materials.     

磷酸铁锂离子电池正极材料掺碳纳米管的研究

应用球磨法于LiFePO4掺杂多壁碳纳米管,制成LiFePO4/MWCNTs复合电极,然后以其组装成锂离子电池.研究不同比例掺杂多壁碳纳米管对复合材料电极电化学性能的影响.XRD、SEM表征及电化学性能测试表明,多壁碳纳米管含量为10%(bymass)的LiFePO4/MWCNTs电极比其它比例的复合电极具有更优良的充放电性能,而且极化小、稳定性强、充放电平台更平稳,导电率更高.在常温0.1C下充放电,首次充、放电比容量分别为139和128.5mAh.g-1,库仑效率达92.4%,循环40次后,电极比容量损失率仅为5.3%.