Temporal evolution study of the plasma induced by CO2 pulsed laser on targets of titanium oxides

This paper reports studies on time-resolved laser induced breakdown spectroscopy (LIBS) of plasmas induced by IR nanosecond laser pulses on the titanium oxides TiO and TiO₂ (anatase). LIBS excitation was performed using a CO₂ laser. The laser-induced plasma was found strongly ionized yielding Ti⁺, O⁺, Ti^2 +, O^2 +, Ti^3 +, and Ti^4 + species and rich in neutral titanium and oxygen atoms. The temporal behavior of specific emission lines of Ti, Ti⁺, Ti^2 + and Ti^3 + was characterized. The results show a faster decay of Ti^3 + and Ti^2 + ionic species than that of Ti⁺ and neutral Ti atoms. Spectroscopic diagnostics were used to determine the time-resolved electron density and excitation temperatures. Laser irradiation of TiO₂-anatase induces on the surface sample the polymorphic transformation to TiO₂-rutile. The dependence on fluence and number of irradiation pulses of this transformation was studied by micro-Raman spectroscopy.     

Thermodynamic properties of calcium titanates: CaTiO3, Ca4Ti3O10, and Ca3Ti2O7

The chemical potentials of CaO in two-phase fields (TiO₂ + CaTiO₃), (CaTiO₃ + Ca₄Ti₃O₁₀), and (Ca₄Ti₃O₁₀ + Ca₃Ti₂O₇) of the pseudo-binary system (CaO + TiO₂) have been measured in the temperature range (900 to 1250) K, relative to pure CaO as the reference state, using solid-state galvanic cells incorporating single crystal CaF₂ as the solid electrolyte. The cells were operated under pure oxygen at ambient pressure. The standard Gibbs free energies of formation of calcium titanates, CaTiO₃, Ca₄Ti₃O₁₀, and Ca₃Ti₂O₇, from their component binary oxides were derived from the reversible e.m.f.s. The results can be summarised by the following equations: CaO(solid) + TiO₂(solid) → CaTiO₃(solid), ΔG° ± 85/(J · mol^?1) = ?80,140 ? 6.302(T/K); 4CaO(solid) + 3TiO₂(solid) → Ca₄Ti₃O₁₀(solid), ΔG° ± 275/(J · mol^?1) = ?243,473 ? 25.758(T/K); 3CaO(solid) + 2TiO₂(solid) → Ca₃Ti₂O₇(solid), ΔG° ± 185/(J · mol^?1) = ?164,217 ? 16.838(T/K).The reference state for solid TiO₂ is the rutile form. The results of this study are in good agreement with thermodynamic data for CaTiO₃ reported in the literature. For Ca₄Ti₃O₁₀ Gibbs free energy of formation obtained in this study differs significantly from that reported by Taylor and Schmalzried at T = 873 K. For Ca₃Ti₂O₇ experimental measurements are not available in the literature for direct comparison with the results obtained in this study. Nevertheless, the standard entropy for Ca₃Ti₂O₇ at T = 298.15 K estimated from the results of this study using the Neumann–Koop rule is in fair agreement with the value obtained from low-temperature heat capacity measurements.     

A study of the photodeposition over Ti/TiO2 electrode for electrochemical detection of heavy metal ions

Here we reported that UV light irradiation can significantly enhance sensitivity of Ti/TiO₂ electrode for determination of trace heavy metal ions (such as Cu^2 +, Pb^2 + and Cd^2 +) owing to the photodeposition of metal ions on the surface of electrodes. The sensitivity of heavy metal ions can be selectively enhanced over the Ti/TiO₂ electrode, which is attributed to matching between potential of heavy metal ions and the position of the conduction band of TiO₂.     

Spectroscopic properties of RBiBO4 (R = Ca,Sr) glasses doped with TiO2

Transparent glasses, melt quenching derived, containing 10RO·20Bi₂O₃·(70 ? x)B₂O₃·xTiO₂ [R = Ca, Sr] with x = 0, 0.5, 1.0 wt% were characterized by X-ray powder diffraction. Physical and spectroscopic properties viz., density, absorption, emission, electron paramagnetic resonance (EPR) and FTIR were investigated. The absorption band around 823 nm in pure glass samples is attributed to the electronic transition of ³P₀ to ³P₂ of Bi⁺ radicals. A small absorption hump centered around 609 nm is found in all doped glasses due to ²T_2g to ²E_g transition of octahedral Ti³⁺ ions. The emission results revealed that all the samples exhibit a broad emission band covering entire visible-light range, with λ_ex = 360 nm, centered 470–520 nm corresponds to electronic transition of ³P₁ to ¹S₀ of Bi³⁺ ions, therefore the present materials can be potentially used as tunable or full-color display systems. And a strong emission around 706 nm with λ_ex = 514 nm due to transition of ²P_3/2 to ²P_1/2 of Bi²⁺ ions. In SrO mixed glasses Ti⁴⁺ ions effect the environment of Bi³⁺ ion symmetry units from C₂ to C_3i. A small EPR signal (at room temperature) is observed in titanium doped glasses due to Ti³⁺ ions. In both the series with increase of TiO₂ concentration BO₄ units are gradually converted into BO₃ units and new cross linkages are formed, like B–O–Ti, Bi–O–Ti at the expense of B–O–B bonds.     

The Preparation of Dye Sensitized Solar Cell (DSSC) from TiO2 and Tamarillo Extract

Energy crisis is what being faced by every country today. Many efforts have been devoted to overcome the problems. One of several offered solutions is to develop solar cells (SCs) since solar energy is abundant and free to use. Especially in a tropical country like Indonesia, solar energy is available a whole year with quite high power 450 mWcm^-2. Several types of SCs, especially silicon-based, have been mass-produced and applied in our daily life. Silicon-based SC has high efficiency yet has high price. Dye Sensitized Solar Cell is an inexpensive type of SC. The natural ingredients could be utilized as dyes for DSSC. In this research, tamarillo extract was employed as the dye for TiO₂-based DSSC. TiO₂ powder was spin-coated on top of Fluorine- Doped Tin Oxide (FTO) conductive glass and calcined at 550 ̊C, 650 ̊C and 750 ̊C each for 60 and 120 min. Scanning ElectronMicroscope (SEM) and X-Ray Diffractometer (XRD) were used to characterize the morphology and structure of the material. Brunauer-Emmet-Teller (BET) analysis was utilized to measure the material active surface area. As the result, the sample calcined at 650 ̊C for 60 minutes showed the highest electrical performance of 542.5 mV and 0.356 mAcm^-2 which corresponded to an SC efficiency of 0.043%. This result was supported by the BET analysis showing the sample calcined at 650 ̊C for 60 min had the largest active surface area of 9.3 m²g^-1. A large active surface area enabled more dye and electrolyte to be stored inside the material so that photon adsorptions from solar energy became more effective and resulting in higher efficiency. Despite of the small efficiency, this work demonstrated the opportunities of tamarillo and TiO₂ to be applied as a DSSC.     

Li(4−x)/3Ti(5−2x)/3CrxO4 (0 ≤ x ≤ 0.9) spinels: New negatives for lithium batteries

Members of the spinel solid solution between Li_4/3Ti_5/3O₄ and LiCrTiO₄, i.e., Li_(4−x)/3Ti_(5−2x)/3Cr_xO₄ (0 ≤ x ≤ 0.9), have been investigated as possible negative electrodes for future lithium-ion batteries. Electrochemical behaviour have been studied over the potential range 1–3.5 V vs Li⁺/Li. Results are promising with anodic capacities between 129 and 163 mA h/g with a flat operating voltage at about 1.5 V, which is attributed to the pair Ti⁴⁺/Ti³⁺. The inclusion of Cr³⁺ in the spinel structure enhances the specific capacity. In-situ X-ray diffraction experiments confirm that the reaction proceeds in a topotactic manner.     

Synthesis,structure and solid state NMR analysis of a new templated titanium(III/IV) fluorophosphate

The title compound MIL-131 (MIL stands for Material from Institut Lavoisier) was prepared hydrothermally (4 days, 473 K, autogenous pressure) in the presence of an organic base (N((CH₂)₂NH₂)₃). The structure of MIL-131 or Ti^IIITi^IV(OH)F₄(HPO₄)·(PO₄)·(N((CH₂)₂NH₃)₃) has been determined ab initio from X-Ray synchrotron powder diffraction data using simulated annealing methods and was refined in the triclinic space group P-1 (no. 2). MIL-131 exhibits a one-dimensional structure built up from inorganic chains of corner sharing TiO₅(OH) titanium(III) octahedra and PO₄ and HPO₄ phosphate tetrahedra, related to TiO₂F₄ titanium octahedra. Protonated triamine cations are located between the inorganic motifs, and interact strongly with the mineral network through hydrogen bondings both with terminal fluorine atoms and hydroxo or oxo groups. Multinuclear solid state NMR has allowed a clear attribution of the protons, fluoride, and phosphate groups environment within the framework of MIL-131. The large values of chemical shift anisotropy together with the absence of any ¹³C NMR response confirmed the presence of paramagnetic titanium(III) species deduced from the crystal structure. Finally, 2D MAS ¹H-³¹P CP-HETCOR NMR correlation experiment gives some insight on the nature of the intra-framework hydrogen bonding.Crystal data for MIL-131: a = 14.109(1) Å, b = 8.462(3) Å, c = 7.179(1) Å, α = 93.772(1)°, β = 96.566(2)°, γ = 98.004(1)°, V = 840.36(2) ų, z = 2.     

Photocatalytic decomposition of 4-chlorophenol over an efficient N-doped TiO2 under sunlight irradiation

Using a new nitrogen precursor of a mixture of ammonia and hydrazine hydrate, N-doped TiO₂ photocatalyst with a high efficiency under visible light was synthesized by a precipitation method. The analysis of X-ray photoelectron spectroscopy (XPS) suggested that the doping concentration of nitrogen was 0.45 at%, while it was 0.21 at% or 0.24 at% using single ammonia or hydrazine hydrate as nitrogen precursor. The patterns of the electron paramagnetic resonance spectroscopy (EPR) indicated that the paramagnetic species of NO₂^2?, NO and Ti³⁺ existed as the proposed active species. The ultraviolet–visible (UV–vis) spectra revealed that the band-gap of the N-doped TiO₂ was 3.12 eV, which was slightly lower than 3.15 eV of pure TiO₂. The N-doped TiO₂ showed higher efficiency under both ultraviolet (UV) and visible light irradiations. Moreover, the degradation grade of 4-chlorophenol (4-CP) using the as-synthesized N-doped TiO₂ under sunlight irradiation for 6 h was 82.0%, which was higher than 66.2% of the pure TiO₂, 60.1% or 65.2% of the N-doped TiO₂ using single ammonia or hydrazine hydrate as precursor. Density functional theory (DFT) calculations were performed to investigate the visible light response of the N-doped TiO₂. Our study demonstrated that the visible activities vary well with the concentrations of NO₂^2? species incorporated by N–TiO₂ series photocatalysts and the higher activity of the as-prepared N-doped TiO₂ was attributed to the enhancement of the concentration of NO₂^2? species.     

Surface properties and photoactivity of TiO2 treated with electron beam

The improvement of the TiO₂-photoactivitiy by electron beam treatment (1 MeV) as a function of the absorbed radiation dose (MGy) is reported. The radiation-induced effects in the TiO₂ crystal structure, e.g. change of the Ti³⁺/Ti⁴⁺ ratio, increase of the photoactivity, etc. were investigated. Three methods were implemented in this respect: for the change of the TiO₂ crystal structure X-ray photoelectron spectroscopy and photoluminescence spectroscopy were applied. The photocatalytic activity of the EB-treated TiO₂ was tested by taking the degree of methylene blue photodegradation as a measure of the achieved effect. The obtained experimental data of all testing methods showed that in TiO₂ at an absorbed dose of 0.5 MGy optimum changes in crystal structure of the catalyst occur, resulting in the highest photocatalytic efficiencies.     

Self-assembled Li4Ti5O12/TiO2/Li3PO4 for integrated Li–ion microbatteries

This work aims to maximize the number of active sites for energy storage per geometric area, by approaching the investigation to 3D design for microelectrode arrays. Self-organized Li₄Ti₅O₁₂/TiO₂/Li₃PO₄ composite nanoforest layer (LTL) is obtained from a layer of self organized TiO₂/Li₃PO₄ nanotubes. The electrochemical response of this thin film electrode prepared at 700 °C exhibited lithium insertion and de-insertion at 1.55 and 1.57 V respectively, which is the typical potential found for lithium titanates. The effects of lithium phosphate on lithium titanate are explored for the first time. By cycling between 2.7 and 0.75 V the LTL/LiFePO₄ full cell delivered 145 mA h g^− 1 at an average potential of 1.85 V leading to an energy density of 260 W h kg^− 1 at C/2. Raman spectroscopy revealed that the γ-Li₃PO₄/lithium titanate structure is preserved after prolonged cycling. This means that Li₃PO₄ plays an important role for enhancing the electronic conductivity and lithium ion diffusion.     

Visible LED light photoelectrochemical sensor for detection of L-Dopa based on oxygen reduction on TiO2 sensitized with iron phthalocyanine

The present work describes the development of a new strategy to photoelectrochemical detection of L-Dopa at low potential based on oxygen reduction on TiO₂ sensitized with iron phthalocyanine (FePc/TiO₂). The FePc/TiO₂ composite shows a photocurrent 10-fold higher than that of pure TiO₂ nanoparticles and it was 4-fold higher than that of FePc exploiting visible light. The band gaps of pure TiO₂ nanoparticles, FePc and FePc/TiO₂, calculated according to the Kubelka–Munk equation, were 3.22 eV, 3.11 eV and 2.82 eV, respectively. The FePc/TiO₂ composite showed a low charge transfer resistance in comparison to the photoelectrode modified with FePc or TiO₂. Under optimized conditions, the photoelectrochemical sensor shows a linear response range from 20 up to 190 μmol L^− 1 with a sensitivity of 31.8 μA L mmol^− 1 and limit of detection of 1.5 μmol L^− 1 for the detection of L-Dopa.     

Li4Ti5O12/reduced graphite oxide nano-hybrid material for high rate lithium-ion batteries

A spinel Li₄Ti₅O₁₂ nanoplatelet/reduced graphite oxide nano-hybrid was successfully synthesized by a two-step microwave-assisted solvothermal reaction and heat treatment. The Li₄Ti₅O₁₂ in the hybrid could deliver a discharge capacity of 154 mAhg^? 1 of Li₄Ti₅O₁₂ at 1 C-rate, 128 mAhg^-1 of Li₄Ti₅O₁₂ at 50 C-rate and 101 mAhg^-1 of Li₄Ti₅O₁₂ at 100 C-rate. It demonstrated promising potential as an anode material in a Li-ion battery with excellent rate capability and good cycling.     

Electrochemical and XPS studies of a Nb-containing Ti-based glass-forming alloy system in H2SO4 solution

The corrosion behaviors of Ti₄₀Zr₂₅Ni_12 -xNb_xCu₃Be₂₀ (x = 0, 4, 8, and 12 at.%) alloys in 0.5 mol/L H₂SO₄ solution were studied, aiming to establish the relationship between Nb content and corrosion resistance. The addition of Nb element gives rise to a clear microstructural evolution, from a completely amorphous structure for the alloys without Nb and with 4% Nb alloys to an amorphous/crystalline composite structure for the alloys with 8% and 12% Nb. The alloy with higher Nb content exhibits better corrosion resistance, which can be attributed to the formation of Ti^4 +-, Zr^4 +-, and Nb^5 +-enriched highly protective surface film in corrosive solutions.     

A novel approach for determining total titanium from titanium dioxide nanoparticles suspended in water and biosolids by digestion with ammonium persulfate

Titanium dioxide (i.e. TiO₂) in nano-form is a constituent of many nanomaterials that are used in sunscreens, cosmetics, industrial products and in biomedical applications. Quantification of TiO₂ nanoparticles in various matrixes is a topic of great interest for researchers studying the potential health and environmental impacts of nanoparticles. However, analysis of TiO₂ as Ti⁴⁺ is difficult because current digestion techniques require use of strong acids that may be a health and safety risk in the laboratory. To overcome this problem, we developed a new method to digest TiO₂ nanoparticles using ammonium persulfate as a fusing reagent. The digestion technique requires short times to completion and optimally requires only 1 g of fusing reagent. The fusion method showed >95% recovery of Ti⁴⁺ from 6 μg mL^?1 aqueous suspensions prepared from 10 μg mL^?1 suspension of different forms of TiO_2, including anatase, rutile and mixed nanosized crystals, and amorphous particles. These recoveries were greater than open hot-plate digestion with a tri-acid solution and comparable to microwave digestion with a tri-acid solution. Cations and anions commonly found in natural waters showed no significant interferences when added to samples in amounts of 10 ng to 110 mg, which is a much broader range of these ions than expected in environmental samples. Using ICP-MS for analysis, the method detection limit (MDL) was determined to be 0.06 ng mL^?1, and the limit of quantification (LOQ) was 0.20 ng mL^?1. Analysis of samples of untreated and treated wastewater and biosolids collected from wastewater treatment plants yielded concentrations of TiO₂ of 1.8 and 1.6 ng mL^?1 for the wastewater samples, respectively, and 317.4 ng mg^?1 dry weights for the biosolids. The reactions between persulfate ions and TiO₂ were evaluated using stoichiometric methods and FTIR and XRD analysis. A formula for the fusing reaction is proposed that involves the formation of sulfate radicals.     

Achieving high-rate capacitance of multi-layer titanium carbide (MXene) by liquid-phase exfoliation through Li-intercalation

The stacks of multi-layer Ti₃C₂T_x and other types of MXene materials limit their electrochemical performance. Herein, we report a facile exfoliation technique to improve the exfoliation efficiency through Li-intercalation into Ti₃C₂T_x interlayers in isopropyl alcohol (IPA) with LiOH as intercalant. This de-intercalation method presented here not only effectively delaminates the stacked Ti₃C₂T_x multi-layers into separate few-layer MXene sheets, but also achieves high-rate supercapacitive performance of Ti₃C₂T_x electrode. The as-produced delaminated Ti₃C₂T_x shows highly improved electrochemical capacitive properties from 47 to 115 F g^− 1 at 200 mV s^− 1. Even at extremely high scan rate of 1000 mV s^− 1, a specific capacitance of 82 F g^− 1 is still obtained. The high-rate capability can be attributed to improved ions accessibility into the few-layer structures. This study offers a new and simple exfoliation pathway for MXenes materials to exploit their full potential in energy storage applications.     

Effects of electron beam irradiation on the photoelectrochemical properties of TiO2 film for DSSCs

TiO₂ has been widely utilized for various industrial applications such as photochemical cells, photocatalysts, and electrochromic devices. The crystallinity and morphology of TiO₂ films play a significant role in determining the overall efficiency of dye-sensitized solar cells (DSSCs). In this study, the preparation of nanostructured TiO₂ films by electron beam irradiation and their characterization were investigated for the application of DSSCs. TiO₂ films were exposed to 20–100 kGy of electron beam irradiation using 1.14 MeV energy acceleration with a 7.46 mA beam current and 10 kGy/pass dose rates. These samples were characterized using X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM), and X-ray photoelectron spectroscopy (XPS) analysis. After irradiation, each TiO₂ film was tested as a DSSC. At low doses of electron beam irradiation (20 kGy), the energy conversion efficiency of the film was approximately 4.0% under illumination of simulated sunlight with AM 1.5 G (100 mW/cm²). We found that electron beam irradiation resulted in surface modification of the TiO₂ films, which could explain the observed increase in the conversion efficiency in irradiated versus non-irradiated films.     

Photocatalytic degradation of paraquat and genotoxicity of its intermediate products

The photocatalytic degradation of paraquat (1,1-dimethyl-4,4′-bipyridylium dichloride) aqueous solutions in the presence of polycrystalline TiO₂ Degussa P25 irradiated by near-UV light was investigated. The substrate and total organic carbon concentrations were monitored by UV spectroscopy and TOC measurements, respectively: the complete photocatalytic mineralization of paraquat (20 ppm) was achieved after ca. 3 h of irradiation by using 0.4 g l⁻¹ of catalyst amount at natural pH (ca 5.8). On the contrary no significant photodegradation of paraquat was observed in the absence of TiO₂ under similar experimental conditions. To evaluate the genotoxicity of paraquat and its intermediates produced during heterogeneous photocatalytic treatment, in vitro tests such as Ames test, with and without rat liver microsomal fractions (S9 mix), and micronucleus test, were used. Results obtained with Salmonella typhimurium (strain TA100) showed that paraquat and photocatalytic products were unable to induce gene mutations when photocatalysis was used in the presence of the optimum amount of TiO₂, i.e. 0.4 g l⁻¹, whereas an increase of revertants his⁺ per plate was observed after 300 min irradiation in the presence of very low amount of TiO₂ (0.04 g l⁻¹). The negative results from micronucleus test suggest that mutagenic, but non-clastogenic, late intermediates of paraquat photo-oxidation were formed when the photocatalytic runs of paraquat degradation were carried out by using 0.04 g l⁻¹ of photocatalyst.     

A strategy for scalable synthesis of Li4Ti5O12/reduced graphene oxide toward high rate lithium-ion batteries

Li₄Ti₅O₁₂/reduced graphene oxide (RGO) composites were prepared via a simple strategy. The as-prepared composites present Li₄Ti₅O₁₂ nanoparticles uniformly immobilized on the RGO sheets. The Li₄Ti₅O₁₂/RGO composites possess excellent electrochemical properties with good cycle stability and high specific capacities of 154 mAh g^− 1 (at 10C) and 149 mAh g^− 1 (at 20C), much higher than the results found in other literatures. The superior electrochemical performance of the Li₄Ti₅O₁₂/RGO composites is attributed to its unique hybrid structure of conductive graphene network with the uniformly dispersed Li₄Ti₅O₁₂ nanoparticles.     

Photocurrent generated on a carotenoid-sensitized TiO2 nanocrystalline mesoporous electrode

Photocurrent was observed upon monochromatic illumination of an ITO electrode coated with a TiO₂ nanocrystalline mesoporous membrane with carotenoid 8′-apo-β-caroten-8′-oic acid (ACOA) deposited as a sensitizer (illuminated area 0.25 cm²) and immersed in an aqueous 10 mM hydroquinone (H₂Q), 0.1 M NaH₂PO₄ solution (pH = 7.4) purged with argon, using a platinum flag counter electrode (area 3.3 cm²) and a SCE reference electrode. The carotenoid-sensitized short-circuit photocurrent reached 4.6 μA/cm² upon a 40 μW/cm² incident light beam at 426 nm, with an IPCE (%, incident monochromatic photon-to-photocurrent conversion efficiency) as high as 34%. The short-circuit photocurrent was stable during 1 h of continuous illumination with only a 10% decrease. An open-circuit voltage of 0.15 V was obtained (upon 426 nm, 40 μW/cm² illumination) which remained at a constant value for hours. The observed open-circuit voltage is close to the theoretical value (0.22 V) expected in such a system. The action spectrum resembled the absorption spectrum of ACOA bound on the TiO₂ membrane with a maximum near 426 nm. No decay of the ACOA on the TiO₂ surface was observed after 12 h, presumably because of rapid regeneration of ACOA from ACOA⁺ at the surface by electron transfer from H₂Q.