脱氧核糖核酸（DNA）的极谱伏安行为研究

研究了脱氧核糖核酸的极谱伏安行为，在０．１ｍｏｌ．Ｌ＾－１ＮＨ４Ｃｌ溶液中ＤＮＡ产生一良好的极谱峰，峰电位Ｅｐ＝－１．６５Ｖ（ｖｓ．Ａｇ／ＡｇＣｌ），且峰电流ｉｐ与ＤＮＡ的浓度在４．５＊１０＾－５－３．７＊１０＾－４ｍｏｌ．ＬＯ＾－１范围内呈线性关系，可望用于ＤＮＡ的定量分析。     

KBrO3—KBr紫外分光光度法测定痕量水杨酸

研究了ＨＣｌ溶液中ＫＢｒＯ３－ＫＢｒ紫外分光光度法测定水杨酸的条件,建立了测定痕量水杨酸的新方法。结果表明,在０．６ｍｏｌ／ＬＨＣｌ,３＊１０＾－５ｍｏｌ／ＬＫＢｒＯ３,５＊１０＾－４ｍｏｌ／ＬＫＢｒ,６＊１０＾－４ｍｏｌ／ｌＫＩ溶中测定水杨酸,其线性范围为０．２－４．０ｍｇ／Ｌ,表观摩尔吸光系数为１．９＊１０＾－４Ｌ．ｍｏｌ＾－１．ｃｍ＾－１,Ｓａｎｄｅｌｌ为７．３μｇ／ｃｍ＾２。ｓｇ ｉｆ ｅ     

银微盘电极上碘离子的示差脉冲溶出伏安法

基于Ｉ能与Ａｇ生成难溶出化合物特性，在银微盘电极上研究了Ｉ的示差脉冲溶出伏安法（ＤＰＳＶ）。该法不需镀汞，不要搅拌，可在较稀稀的支持电解质溶液中实施。于０．０８ｍｏｌ／ＬＨＡｃ－ＮａＣ及０．０１ｍｏｌ／ＬＥＤＴＡ介质中，能检出１．００×１０＾－８ｍｏｌ／Ｌ的Ｉ，Ｉ的浓度为５．００×１０＾－６－－１．２０×１０＾－８ｍｏｌ／Ｌ范围与峰电流有良好的线性关系。该法用于自来水中Ｉ的测定，相对偏差为４．３％     

介体型乳酸脱氢酶生物传感器的研制及应用

本报道了能对丙酮酸产生良好响应的电流型乳酸脱氢酶生物传感器。该传感器以耐尔兰Ａ修饰浸石墨电极为基体电极，将酶直接固化在蚕丝蛋白膜上。在ＰＨ７．４的ＮａＨ２ＰＯ４－ＮａＯＨ介质中，当２．４×１０＾－４ｍｏｌ／Ｌ的辅酶Ｉ（ＮＡＤＨ）存在下，该传感器的响应电流与丙酮酸浓度在３．２×１０＾－５ｍｏｌ／Ｌ范围内有良好的线性关系。响应时间为６０ｓ．本讨论了影响传感器响应的各种因素，用此传感器测定了人血清中     

葡萄糖脱氢酶微型生物传感器的研制及应用

以甲苯胺兰（ＴＢ）修饰碳糊微电极为基体，将葡萄糖脱氢酶（ＧＤＨ）用丝素蛋白膜固定于修饰微电极表面制成了生物传感器，在ｐＨ７．０的ＮａＯＨ－ＮａＨ２ＰＯ４缓冲溶液中，烟酰胺腺嘌呤二核苷酸（ＮＡＤ）的浓度为１．０４×１０＾－３ｍｏｌ／Ｌ的条件下，其响应电流与葡萄糖浓度在１．０×１０＾－４～３．２×１０＾－３ｍｏｌ／Ｌ范围内有良好线性关系，响应时间为２０ｓ；检测限为４．０×１０＾－５ｍｏｌ／Ｌ。该传感器     

多菌灵在玻碳电极上的伏安行为及其应用

应用循环伏安法、微分脉冲伏安法对多菌灵在破碳电极上的电化学行为及其测定进行了研究。在ｐＨ＝９．０的２ｍｏｌ／Ｌ ＮＨ３－ＮＨ４Ｃｌ底液中，对其进行循环伏安扫描，发现于０．６１Ｖ（ｖｓ．Ａｇ／ＡｇＣｌ）产生一灵敏的氧化峰。微分脉冲伏安法殉菌灵的检测限为４×１０＾－８ｍｏｌ／Ｌ。多菌灵的浓度在５．０×１０＾－７￣１．０×１０＾－５ｍｏｌ／Ｌ间与微分脉冲伏安峰电流呈线性关系（ｒ＝０．９９４２）。对于１×     

新型杯芳烃银离子选择电极的研究

报道了５,１１,１７,２３－四（１,１－二甲基乙基）－２５,２７－二羟基２６,２８－二「２－乙基硫）乙氧基」杯「４」芳烃为银离子载体的ＰＶＣ膜电极的研制。该银离子选择电极不仅对银离子有良好的灵敏度和高选择性,在１０＾－１－１０＾－５ｍｏｌ／Ｌ浓度范围内有良好的线性,能斯特响应为５６ｍＶ／ｐｅＡｇ．（２５℃）碱金属、碱土金属及过渡金属离子不干扰银的测定;而且对某些阴离子也表现出近似能斯特响应（５０ｍＶ／ｐｃｘ－）。用该电极对人工试样中银含量进行测定,结果与原子吸收光度法相符。     

一阶导数差示脉冲极谱法用于扑热息痛的定量分析

一阶导数差示脉冲极谱法用于扑热息痛及其制剂的定量分析，在乙醇－水－２．０×１０＾－＾３ｍｏｌ／ＬＨ２ＳＯ４（１２．５：１１．５：１）的溶液中，于０．２４Ｖ（ｕｓＡｇ／ＡｇＣｌ）处出现良好的一阶导数差示脉冲极谱峰，在３．３×１０＾－＾４～３．３×１０＾－＾３ｍｏｌ／Ｌ范围内，浓度与其一阶导数差示脉冲极谱峰值呈线性关系，检测限为７．８×１０＾－＾８ｍｏｌ／Ｌ。方法简便，快速，灵敏，结果准确。     

丁基罗丹明B—钼酸盐光度法连续测定铈和钪

在聚乙烯醇（ＰＶＡ）存在下，丁基罗丹明Ｂ（ＢＲＢ）分别与铈钼、钪钼杂多酸络阴离子形成离子缔合物，其最大吸收均位于５７０ｎｍ，表面摩尔吸光度分别为εＣｅ＝３．９６×１０＾６Ｌ．ｍｏｌ＾－１．ｃｍ＾－１，εＳｃ＝４．７１×１０＾５Ｌ．ｍｏｌ＾－１．ｃｍ＾－１，服从比耳定律范围分别为０－２４μｇ／Ｌ Ｃｅ和０－６０μｇ／ＬＳｃ，测定极限为Ｃｅ１．０μｇ／Ｌ（ｎ＝１２）和Ｓｃ１．９μｇ／Ｌ（ｎ＝１０），对     

硫代巴妥酸光度法测定香草醛

香草酸在强酸性介与硫代巴比妥酸（ＴＢＡ）反应生成黄绿色的化合物,建立可见光分光光度法香草醛方法。线性范围１×１０＾－６￣１．５×１０＾－４ｍｏｌ／ｌ,检出限为４．４７×１０＾－８ｍｏｌ／Ｌ。对冰淇淋,麦片等进行了其中香草醛含量测定,结果满意。     

海水重金属电化学传感器检测系统

研制了一种新型的海水重金属电化学传感器流动分析系统.通过在线过滤、紫外线消解、电化学富集以及离子选择性电极电位测定等过程,实现对海水重金属的高灵敏、高选择性的快速检测.在海水基体条件下,对于镉、铅和铜的测定线性范围分别为1.0×10-9～1.0×10-7 mol/L,3.0×10-9～1.0×10-7 mol/L和1.0×10-9～1.0× 10-7 mol/L,相应检出限为2.8×10-10,6.6×10-10和5.1×10-10 mol/L,连续6次测定的RSD均小于5％,全程分析在25 min内完成.应用于实际海水样品分析,其测定结果与溶出伏安法一致.此传感器性能可靠、成本低廉,在海水重金属现场快速监测方面具有良好的应用前景.     

Cesium-selective membrane electrode based on a recently synthesized 16-membered macrocyclic diamide

A PVC membrane sensor for the Cs+ ion based on 1,5-diaza-2,3,4-naphthyl-8,11,14-trioxacyclohexadecane-6,16-dione (L) has been prepared. The sensor has a linear dynamic range of 5.0 x 10(-1) - 6.9 x 10(-6) mol L(-1), a Nernstian slope of 59.5 +/- 0.8 mV decade(-1), and a detection limit of 4.7 x 10(-6) mol L(-1). It has a fast response time of <15 s and can be used for at least 8 weeks without any considerable divergence in potentials. The selectivity of the proposed electrode relative to alkali, alkaline earth, and transition metal ions was comparatively good. The electrode could be used in the pH range 4.5-11.0.     

Thin-layer chromatographic behavior of rare earths on silica gel with aqueous alkaline earth metal nitrate solutions as mobile phases

The TLC behavior of all the rare earths except Pm has been surveyed on silica gel (pH 7.0) pretreated with 0.1 mol L(-1) tris(hydroxymethyl)aminomethane and 0.1 mol L(-1) HCl with aqueous nitrate solutions of alkaline earth metals as mobile phases. The RF values of the lanthanides varied in a regular and characteristic way accompanied by the tetrad effect with increasing atomic number, and when the mobile phases were changed the RF values of each metal decreased in the order Mg2+ > Ca2+ > Sr2+ > Ba2+, as the crystal ionic radii of the alkaline earth metals increased. This adsorption sequence was not observed with alkali metal nitrate and alkali metal chloride mobile phases. A brief discussion concerning the effect on RF values of the solvent cations and the adsorption mechanism is included; also presented are typical chromatograms for the separation of multi-component mixtures containing adjacent lanthanides.     

N~1,N~2-Bis[1-(2-hydroxyphenyl)methylidene]ethanedihydrazide as a neutral ionophore for preparation of a new Ho~(3+) PVC-membrane sensor

N¹,N²-Bis[1-（2-hydroxyphenyl）methylidene]ethanedihydrazide（MEH） was used as new compound which plays the role of an excellent ion carrier in the fabrication of a Ho（Ⅲ） membrane electrode.The electrode shows a good selectivity for Ho（Ⅲ） ion with respect to most common cations including alkali,alkaline earth,transition and heavy metal ions.This electrode has a wide linear dynamic range from 1.0×10^-6 to 1.0×10^-2 mol/L with a Nernstian slope of 19.8±0.3 mV per decade and a low detection limit of 5.8×10^-7 mol/L in the pH range of 2.5-9.8,while the response time was rapid（<10 s）.The suggested sensor was applied to the determination of Ho（Ⅲ） ions in tap water and river water samples.     

钳状杯[4]芳烃为探针的固态PVC膜汞离子选择性电极

全固膜选择性电极(All solid-state selective electrode,ASSE)综合晶体电极和膜电极的优点,具有线性范围宽、检测限低,能真实地体现膜性能等特点,ASSE主要有涂线电极(Coated wire electrode,CWE)、填充固体电解质或配合物的膜电极和电沉积型聚合物膜电极等。     

Erbium(Ⅲ) PVC membrane sensor based on N-(benzyloxycarbonyloxy)succinimide as a new neutral ionophore

In this study,a new Er³⁺ sensor based on N-（benzyloxycarbonyloxy）succinimide（BCS） as a neutral carrier has been constructed. The sensor exhibits potential linear response with a Nernstian slope of 20.5±0.4 mV/decade in the concentration range of 1.0×10^-6to 1.0×10^-2mol/L of Er³⁺.It has a very short response time（<10 s）,detection limit of 6.3×10^-7 mol/L and a good selectivity relative to a wide variety of other metal ions including common alkali,alkaline earth,heavy,and transition metal ions.It can be used in the pH range of 2.5-10.6 without any considerable divergence in potentials.The proposed sensor was successfully applied for the recovery of Er³⁺ ions spiked in tap and river water samples.     

A bismuth(III) PVC membrane ion selective electrode based on 5-(3,4,5-trimethoxyphenyl)-4-amino-1,2,4-triazole-3-thiol

The construction, performance characteristics and application of a new bismuth(III) PVC membrane electrode based on 5-(3,4,5-trimethoxyphenyl)-4-amino-1,2,4-triazole-3-thiol are reported in this paper. The designed sensor exhibited a Nernstian response for Bi³⁺ ion ranging from 5.0×10^-7 mol/L to 1.0×10^-2 mol/L with a slope of 19.8 mV/decade. The operational pH range of the sensor is 3.0-6.0. The electrode shows a response time of 6 s and can be used for at least five weeks without any considerable divergence in potentials. It exhibits very good selectivity relative to a wide variety of alkali, alkaline earth, transition and heavy metal ions. The proposed electrode could be used as an indicator electrode in potentiometric titration of Bi³⁺ ions with EDTA and in the determination of Bi³⁺ content in stomach medicine.     

Use of a Carbon Paste Electrode Modified with Spinel‐Type Manganese Oxide as a Potentiometric Sensor for Lithium Ions in Flow Injection Analysis

A potentiometric sensor constructed from a mixture of 25% (m/m) spinel‐type manganese oxide (lambda‐MnO₂), 50% (m/m) graphite powder and 25% (m/m) mineral oil is used for the determination of lithium ions in a flow injection analysis system. Experimental parameters, such as pH of the carrier solution, flow rate, injection sample volume, and selectivity for Li⁺ against other alkali and alkaline‐earth ions and the response time of this sensor were investigated. The sensor response to lithium ions was linear in the concentration range 8.6×10^?5–1.0×10^?2 mol L^?1 with a slope 78.9±0.3 mV dec^?1 over a wide pH range 7–10 (Tris buffer), without interference of other alkali and alkaline‐earth metals. For a flow rate of 5.0 mL min^?1 and a injection sample volume of 408.6 μL, the relative standard deviation for repeated injections of a 5.0×10^?4 mol L^?1 lithium ions was 0.3%.     

Coated-wire copper(II)-selective electrode based on phenylglyoxal-α-monoxime ionophore

A copper(II) ion-selective electrode based on a recently synthesized 2-quinolyl-2-phenylglyoxal-2-oxime (phenylglyoxal-alpha-monoxime) has been developed. The PVC-based membrane containing phenylglyoxal-alpha-monoxime, dibutyl phthalate as plasticizer, and sodium tetraphenylborate as anion excluder and membrane modifier, was directly coated on the surface of a platinum-wire electrode. The response of the electrode was linear with a near-Nernstian slope of 28.2 mV decade(-1) within the Cu2+ ion concentration range 1x10(-6)-1x10(-1) mol x L(-1). The response time for the proposed electrode to achieve a 95% steady potential for Cu2+ concentrations ranging from 1x10(-1) to 1x10(-6) mol x L(-1) is between 10 and 50 s, and the electrode is suitable for use within the pH range of 3 to 6.5. The electrode has a detection limit of 5x10(-7) mol x L(-1) Cu2+ and its selectivity relative to several alkali, alkaline earth, transition, and heavy metal ions was good. The coated-wire electrode could be used for at least two months without a considerable alteration of its potential. Applications of the electrode for determination of copper in milk powder samples and as an indicator electrode for potentiometric titration of Cu2+ ion using EDTA are reported.