Evaluation of new high-density ion exchange adsorbents for expanded bed adsorption chromatography

New adsorbents Q HyperZ and CM HyperZ composed of hydrogel-filled porous zirconium oxide particles were evaluated for expanded bed adsorption applications in the present work. The HyperZ adsorbents have wet density of 3.16 g ml(-1), particle size of 44.5-100.8 microm and average sphere diameter of 67 microm. The bed expansion as the function of flow velocity and fluid viscosity was measured and correlated with Richardson-Zaki equation. The suitable expansion factor was considered less than 2.5, while the corresponding flow velocity was about 450 cmh(-1). Liquid mixing in the bed was determined to evaluate the stability of expanded bed. The Bodenstein numbers tested were higher than 40 and the axial mixing coefficients (D(ax)) were between 0.5 and 9.7x10(-6)m(2)s(-1), which demonstrated that a stable expanded bed could be formed under suitable operation conditions. Bovine serum albumin (BSA) and lysozyme were used as model proteins to estimate the adsorption capacities of Q and CM HyperZ, respectively. The maximum equilibrium adsorption of Q and CM HyperZ could reach 45.7 and 27.2 mg g(-1) drained adsorbents, respectively. It was found that yeast cells had little influence on the adsorption capacities of the two adsorbents tested. The dynamic adsorption capacity of BSA at 10% breakthrough with Q HyperZ was 35.9 mg g(-1) drained adsorbent at flow velocity of 100 cm h(-1) for packed bed adsorption. The values for expanded bed adsorption were 34.4 mg g(-1) drained adsorbent at flow velocity of 200 cm h(-1), 33.6 mg g(-1) drained adsorbent at 300 cm h(-1) and 31.7 mg g(-1) drained adsorbent 400 cm h(-1). The results demonstrated that Q HyperZ and CM HyperZ are suitable for expanded bed adsorption of biomolecules.     

Improved purification of immunoglobulin G from plasma by mixed‐mode chromatography

Efficient loading of immunoglobulin G in mixed‐mode chromatography is often a serious bottleneck in the chromatographic purification of immunoglobulin G. In this work, a mixed‐mode ligand, 4‐(1H‐imidazol‐1‐yl) aniline, was coupled to Sepharose Fast Flow to fabricate AN SepFF adsorbents with ligand densities of 15–64 mmol/L, and the chromatographic performances of these adsorbents were thoroughly investigated to identify a feasible approach to improve immunoglobulin G purification. The results indicate that a critical ligand density exists for immunoglobulin G on the AN SepFF adsorbents. Above the critical ligand density, the adsorbents showed superior selectivity to immunoglobulin G at high salt concentrations, and also exhibited much higher dynamic binding capacities. For immunoglobulin G purification, both the yield and binding capacity increased with adsorbent ligand density along with a decrease in purity. It is difficult to improve the binding capacity, purity, and yield of immunoglobulin G simultaneously in AN SepFF chromatography. By using tandem AN SepFF chromatography, a threefold increase in binding capacity as well as high purity and yield of immunoglobulin G were achieved. Therefore, the tandem chromatography demonstrates that AN SepFF adsorbent is a practical and feasible alternative to MEP HyperCel adsorbents for immunoglobulin G purification.     

Adsorption Strategy of Plasmid DNA Nanoparticulate: Preparative Purification by a Simple Custom Expanded Bed Column

This paper summarizes the critical examination of the hydrodynamic performance of the NBG expanded bed contactor operated with streamline-DEAE adsorbent under various operating conditions for expanded bed adsorption of plasmid DNA nanoparticles from alkaline lysate. The purification process is not RNase-free. In this study, a rapid and efficient scaleable purification protocol obtaining, plasmid DNA nanoparticles (average size of 40 nm) with a high purity level for use as therapeutic agent in customized NBG expanded bed columns was developed. This technique allows efficient levels of binding to the column media and vector purification without centrifugation or filtration steps. Residence time distribution (RTD) studies were exploited to achieve the optimal condition of plasmid DNA nanoparticle (pDNA) recovery upon anion exchange adsorbent in this contactor. In addition, the purification experiments were carried out in the expanded bed columns with settle bed height of 6.0 ± 0.2 cm. NaCl gradient elution enabled the isolation of supercoiled plasmid from low-Mr RNA, cDNA and plasmid variants. Subsequently dynamic binding capacity of the adsorbent was calculated while these values decreased with increase in flow velocity. Moreover, the effect of pH upon the performance of this recovery process and the feedstock volume upon the expanded bed anion exchange purification was investigated. The results demonstrated that separation of low-Mr RNA from plasmid DNA isoforms in the range of pH between 5.5 and 7.5 is achievable in this column. The yield of recovery of pDNA in optimal condition was higher than 88.51% which was a superior result in one-pass frontal chromatography. The generic application of simple customized NBG expanded bed column and its potential for the purification and recovery of plasmid DNA as a nanoparticulate bioproduct is strongly discussed.     

Modeling of the whole expanded-bed protein adsorption process with yeast cell suspensions as feedstock

Expanded bed adsorption of bovine serum albumin (BSA) directly from a feedstock containing whole yeast cells has been investigated with an anion-exchanger DEAE Spherodex M. In the presence of 6% (w/w) yeast cells, the axial liquid-phase dispersion coefficient was found in the order of 10(-6) m2/s, which felled into the common range of 1.0 x 10(-6)-1.0 x 10(-5) m2/s observed previously without the use of cell suspensions as mobile phase. We found that the static and dynamic binding capacity of BSA decreased with increasing the yeast cell concentration due to the competitive adsorption of cells onto the outer surface of the anion-exchanger. However, because of the small size of the adsorbent, the large pore diffusivity of protein and the favorable column efficiency (low axial dispersion coefficient), the dynamic binding capacity of BSA in the presence of 6% (w/w) cells in the expanded bed reached 86% that of the equilibrium adsorption density. Then, the whole expanded bed adsorption process of BSA in the presence of cells, including feedstock loading, washing and elution steps, was predicted using a mathematical model with parameters all determined independently. In the elution stage, the steric mass-action adsorption isotherm with salt concentration as one of the model parameters was used to predict the step-gradient elution process with salt concentration increases. Computer simulations showed that the model was in good agreement with the experimental results for the whole operation process.     

N-去甲万古霉素亲和吸附剂的合成及性能

将N,N二甲基丙烯酰胺N,N′乙撑双丙烯酰胺共聚物部分水解,在共聚物中引入适量的羧基.含羧基的聚合物与氨基酸甲酯缩合,然后使酯基皂化,将氨基酸引入聚合物.将革兰氏阳性菌细胞壁粘肽的三种类似物(-Gly,-Gly-DAla,-Gly-DAla-DAla)分别引入上述聚合物,合成了3种万古霉素系列抗菌素的亲和吸附剂(Ⅰ,Ⅱ和Ⅲ).结果表明,吸附剂Ⅱ和吸附剂Ⅲ对N去甲万古霉素的吸附量分别为0.80和0.86mmol/g;最佳吸附pH值为6左右;吸附剂Ⅰ的吸附量随着吸附液中盐浓度的增加而显著降低,而吸附液中盐浓度对吸附剂Ⅱ的吸附量影响较小.说明亲和作用在吸附剂Ⅱ的吸附中贡献较大.用0.4mol/LNa₂CO₃(pH9.5)/CH₃CN(体积比为7/3)作为洗脱剂可完全脱附被吸附的N去甲万古霉素.     

Expanded Bed Chromatography as a Tool for Nanoparticulate Separation: Kinetic Study and Adsorption of Protein Nanoparticles

Expanded bed adsorption was investigated together with its suitability for the practical recovery of nanoparticulate mimics of products such as plasmid DNA and viruses as putative gene therapy vectors. The study assessed the binding of protein nanoparticles fabricated from bovine serum albumin (BSA) with average size of 80 nm as a model system and viral size/charge mimic to the streamline DEAE adsorbent in the expanded bed column chromatography. The adsorption kinetics and adsorption mechanism for the BSA nanoparticles on the adsorbent were studied. In batch adsorption studies, the factors nanoparticle concentration, contact time and adsorbent amount, affecting adsorption isotherms were investigated. Subsequently the data were regressed against the Lagergren equation, which represents a first-order kinetics equation and also against a pseudo-second-order kinetics equation. The results demonstrated that the adsorption process followed a Langmuir isotherm equation. The kinetics of the adsorption process followed a pseudo-second-order kinetics model with a rate constant value of 0.025 g mg^?1 min^?1. The dynamic binding capacity of the BSA nanoparticles on an expanded bed was calculated. The recovery of the nanoparticles was more than 85%.     

Hydrophobic interaction chromatography of proteins. IV. Protein adsorption capacity and transport in preparative mode

The adsorption isotherms of four model proteins (lysozyme, α-lactalbumin, ovalbumin, and BSA) on eight commercial phenyl hydrophobic interaction chromatography media were measured. The isotherms were softer than those usually seen in ion-exchange chromatography of proteins, and the static capacities of the media were lower, ranging from 30 to 110 mg/mL, depending on the ammonium sulfate concentration and the protein and adsorbent types. The protein-accessible surface area appears to be the main factor determining the binding capacity, and little correlation was seen with the protein affinities of the adsorbents. Breakthrough experiments showed that the dynamic capacities of the adsorbents at 10% breakthrough were 20-80% of the static capacities, depending on adsorbent type. Protein diffusivities in the adsorbents were estimated from batch uptake experiments using the pore diffusion and homogeneous diffusion models. Protein transport was affected by the adsorbent pore structures. Apparent diffusivities were higher at lower salt concentrations and column loadings, suggesting that adsorbed proteins may retard intraparticle protein transport. The diffusivities estimated from the batch uptake experiments were used to predict column breakthrough behavior. Analytical solutions developed for ion-exchange systems were able to provide accurate predictions for lysozyme breakthrough but not for ovalbumin. Impurities in the ovalbumin solutions used for the breakthrough experiments may have affected the ovalbumin uptake and led to the discrepancies between the predictions and the experimental results.     

胆红素吸附剂功能基组成及其吸附特性研究

为了获得性能较佳的胆红素吸附剂,本研究考察了功能基种类、链长、偶联密度等因素对吸附剂吸附性能的影响。结果表明,当功能基具有足够的链长,与胆红素相似的疏水性及较高的偶联密度时,能够提高吸附剂的胆红素吸附能力。实验表明,链长21个原子、偶联73 mol/mL正丁胺的吸附剂对胆红素的吸附能力最强,在30℃、300mg/L的白蛋白结合胆红素溶液中,吸附1h即达到平衡,胆红素吸附量达到3.01mg/mL(90.3mg/g干重);较高的温度有利于其对胆红素的吸附。50mL材料对500mL实际病人血浆动态吸附2.5h,总胆红素(277.4mg/L)去除率达到55.2%,同时对血浆蛋白的吸附较低。所有结果显示该吸附剂具有很强的实际应用的潜力。     

DNA-induced inter-particle cross-linking during expanded bed adsorption chromatography. Impact on future support design

We have investigated the effects of adsorbent size, ionic capacity and surface immobilised polymers on dynamic capacity and changes occurring to beds of anion-exchangers during the binding of DNA. During application of low concentrations of "3-20 kilobase" calf thymus DNA feeds to expanded beds of anion-exchangers, the bed heights dropped progressively as DNA molecules physically cross-linked neighbouring adsorbent particles together, to form severely aggregated fluidised beds. In plots of dynamic binding capacities and absolute changes in bed porosity at maximum contraction, against the inverse of the mean hydrated particle radii, the anion-exchangers were observed to split into three distinct, but different clusters in each case. The highest index of surface packing of DNA was observed for two prototype pellicular supports, one derivatised with highly charged high molecular mass polyethyleneimine (Mr approximately 50,000) and the other with long dextran (Mr approximately 500,000) chains weakly derivatised with DEAE. However, the ability of the surfaces of these two matrices to bring about bed contraction, was strikingly different. The highly charged surface afforded by coupling of polyethyleneimine exhibited a three-fold higher tendency to interact with neighbouring particles in the presence of DNA than that of the dextran DEAE support. The implications of these findings on the design of future expanded bed materials for separation of both proteins and nucleic acids are discussed.     

一种球形纤维素/钛白粉扩张床吸附剂的研究--组成对性能的影响

采用反相悬浮再生法 ,以超细钛白粉颗粒作增重剂 ,包埋于纤维素骨架之中 ,经环氧氯丙烷活化后与二乙胺连接 ,制得一种球形扩张床吸附剂 .研究表明 ,吸附剂的密度、机械强度和孔结构可以随钛白粉用量的变化而改变 ;钛白粉颗粒的掺入有利于基质的活化 ,活化后环氧基含量可达 2 2 0 μmol mL .吸附剂具有良好的扩张床性能 ,扩张床中的蛋白质吸附行为与填充床中相似 ,吸附容量为 4 8 9mg牛血清白蛋白 mL吸附剂     

High-throughput isotherm determination and thermodynamic modeling of protein adsorption on mixed mode adsorbents

The thermodynamic modeling of protein adsorption on mixed-mode adsorbents functionalized with ligands carrying both hydrophobic and electrostatic groups was undertaken. The developed mixed mode isotherm was fitted with protein adsorption data obtained for five different proteins on four different mixed mode adsorbents by 96-well microtitre plate high throughput batch experiments on a robotic workstation. The developed mixed mode isotherm was capable of describing the adsorption isotherms of all five proteins (having widely different molecular masses and iso-electric points) on the four mixed mode adsorbents and over a wide range of salt concentrations and solution pH, and provided a unique set of physically meaningful parameters for each resin-protein-pH combination. The model could capture the typically observed minimum in mixed mode protein adsorption and predict the precise salt concentration at which this minimum occurs. The possibility of predicting the salt concentration at which minimum protein binding occurs presents new opportunities for designing better elution strategies in mixed mode protein chromatography. Salt-protein interactions were shown to have important consequences on mixed mode protein adsorption when they occur. Finally, the mixed mode isotherm also gave very good fit with literature data of BSA adsorption on a different mixed mode adsorbent not examined in this study. Hence, the mixed mode isotherm formalism presented in this study can be used with any mixed mode adsorbent having the hydrophobic and electrostatic functional groups. It also provides the basis for detailed modeling and optimization of mixed mode chromatographic separation of proteins.     

Microcalorimetric studies of interactions between proteins and hydrophobic ligands in hydrophobic interaction chromatography: effects of ligand chain length, density and the amount of bound protein

Using isothermal titration calorimetry (ITC), this investigation directly measured the adsorption enthalpies of proteins on various hydrophobic adsorbents. Various amounts of butyl and octyl groups were attached onto CM-Sepharose to form C4 and C8, two types of hydrophobic adsorbents. The adsorption enthalpies of both trypsinogen and alpha-chymotrypsinogen A were measured at 4.0 M NaCl and pH 10.0, in which most ionic interaction was suppressed. The adsorption isotherms of both proteins on various adsorbents were also measured, thus allowing us to calculate the Gibbs free energy and entropy of adsorption. Experimental results indicated that the adsorption of both proteins on butyl-containing adsorbents was exothermic, while their adsorption on octyl ones was endothermic. In addition, binding of both proteins with the butyl ligand is basically an adsorption process, while binding with the octyl ligand is adsorption and partition processes. Moreover, on both butyl or octyl, the adsorption enthalpy became increasingly positive as the ligand density increased, while the adsorption entropy became more positive as the alkyl chain length or density of the adsorbent increased. In addition, ITC was used to measure protein-protein interaction. The adsorption enthalpy of both proteins increased as the amount of bound protein increased, and the enthalpy increase of trypsinogen appeared to be higher than that of alpha-chymotrypsinogen A. This observation implies that protein-protein repulsion was stronger among trypsinogen molecules in the experiments.     

Preparation and evaluation of polymer-coated adsorbents for the expanded bed recovery of protein products from particulate feedstocks

A novel prototype polymer-coated adsorbent (PCA) has been developed for the effective expanded bed recovery of protein products from particulate feedstocks. The adsorbents were manufactured using the three-phase emulsification process by which the selected core phases (anion- and cation-exchangers and a custom-assembled pseudo-affinity adsorbent) were coated by an agarose gel. This new non-stick exterior coating acts as a sieve reducing the non-specific binding of cell and cell debris without diminution of selective capture of target protein from complex feedstocks such as whole microbial broths and cell disruptates. The new coated adsorbents were subjected to physical and hydrodynamical comparison with the performance of their uncoated adsorbents. Hydrodynamic characteristics (e.g. axial dispersion coefficient (D(axl)) and Bodenstein number (B(o))) of PCA demonstrated a marked robustness in the face of biomass loading disrupted yeast cells. In addition, each adsorbent was compared with its uncoated native form during the expanded bed adsorption of one of two intracellular proteins (i.e. glyceraldehyde 3-phosphate dehydrogenase and cytochrome c) from a 20% (ww/v) yeast disruptate. The performance parameters of efficiency of washing, purification factor, turbidity of the eluted product and protein recovery in all analysed cases were favourable to the coated materials. In particular, exploiting PCA reduced significantly undesirable adsorption of cells without significant loss of binding capacity for the target product. The generic application of such adsorbents and their potential for the recovery of target products from complex feedstock is discussed, whilst other application such as the subtractive purification of nanoparticles were detailed in our previous publication.     

Pressure-Swing Adsorption Using Layered Adsorbent Beds with Different Adsorption Properties: I—Results of Process Simulation

A simulation study was conducted on layered-bed pressure-swing adsorption, PSA, processes with adsorbents that differ in their adsorption properties. As an example, an oxygen, O₂, vacuum-swing adsorption, VSA, process was analyzed to investigate relationships between process performance and adsorption properties of the adsorbents used. For two adsorbents with identical nitrogen-to-oxygen, N₂/O₂, selectivity but different N₂ and O₂ capacities, placing the high-capacity adsorbent at the product end and the low-capacity adsorbent at the feed end of the adsorption bed gives a better performance than the case of reversing layering of these adsorbents. However, for two adsorbents with different values of N₂/O₂ selectivity but identical N₂ capacity, changing the bed-layer configuration does not show a significant difference in O₂-VSA performance. The advantages of layering a high-capacity adsorbent on product end of the bed are demonstrated by an examination of the N₂-loading difference in a VSA cycle. The modeling study also reveals an effect of cycle features (e.g., equalization step) on the effectiveness of using layered-bed configurations in VSA/PSA processes. It suggests that layering appropriately two adsorbents with different adsorption properties could result in better VSA/PSA-process performance than using a single-layer bed with either of the two adsorbents.     

Aqueous mercury adsorption in a fixed bed column of thiol functionalized mesoporous silica

The aim of this work was to investigate the aqueous mercury adsorption in a fixed bed of mesostructured silica SBA-15 functionalized with propylthiol by co-condensation (SBA-15-SH). Powdered synthesized adsorbents were used to prepare pellets with sizes ranging from 0.5 to 1 mm. The physicochemical properties determined from N₂ adsorption and chemical analysis were compared for powder and pellets. Batch static experiments were carried out to obtain the equilibrium mercury adsorption isotherms, resulting that although the maximum adsorption capacity was reduced from powder to pellets, the materials maintained high efficiency for mercury removal even at very low aqueous metal concentration. Dynamic experiments were carried out in a fixed bed column by modifying the volumetric flow rate, bed length, inlet concentration, and amount of propylthiol groups incorporated to the adsorbent, and analyzing the temporal scale and the mercury adsorption capacities. The elution of the fixed bed was carried out chemically by circulating an aqueous 2 M hydrobromic acid stream for 2 h so achieving a complete recovery of the mercury previously adsorbed. Simplified dynamic equations of Bohart–Adams and Wolborska were used for modeling the breakthrough curves.     

Surface modification of chromatography adsorbents by low temperature low pressure plasma

In this study we show how low temperature glow discharge plasma can be used to prepare bi-layered chromatography adsorbents with non-adsorptive exteriors. The commercial strong anion exchange expanded bed chromatography matrix, Q HyperZ, was treated with plasmas in one of two general ways. Using a purpose-designed rotating reactor, plasmas were employed to either: (i) remove anion exchange ligands at or close to the exterior surface of Q HyperZ, and replace them with polar oxygen containing functions (‘plasma etching and oxidation’); or (ii) bury the same surface exposed ligands beneath thin polymer coatings (‘plasma polymerization coating’) using appropriate monomers (vinyl acetate, vinyl pyrrolidone, safrole) and argon as the carrier gas. X-ray photoelectron spectroscopy analysis (first ∼10 nm depth) of Q HyperZ before and after the various plasma treatments confirmed that substantial changes to the elemental composition of Q HyperZ's exterior had been inflicted in all cases. The atomic percent changes in carbon, nitrogen, oxygen, yttrium and zirconium observed after being exposed to air plasma etching were entirely consistent with: the removal of pendant Q (trimethylammonium) functions; increased exposure of the underlying yttrium-stabilised zirconia shell; and introduction of hydroxyl and carbonyl functions. Following plasma polymerization treatments (with all three monomers tested), the increased atomic percent levels of carbon and parallel drops in nitrogen, yttrium and zirconium provided clear evidence that thin polymer coats had been created at the exteriors of Q HyperZ adsorbent particles. No changes in adsorbent size and surface morphology, nor any evidence of plasma-induced damage could be discerned from scanning electron micrographs, light micrographs and measurements of particle size distributions following 3 h exposure to air (220 V; 35.8 W L⁻¹) or ‘vinyl acetate/argon’ (170 V; 16.5 W L⁻¹) plasmas. Losses in bulk chloride exchange capacity before and after exposure to plasmas enabled effective modification depths within hydrated Q HyperZ adsorbent particles to be calculated as 0.2–1.2 μm, depending on the conditions applied. The depth of plasma induced alteration was strongly influenced by the power input and size of the treated batch, i.e. dropping the power or increasing the batch size resulted in reduced plasma penetration and therefore shallower modification. The selectivity of ‘surface vs. core’ modification imparted to Q HyperZ by the various plasma treatments was evaluated in static and dynamic binding studies employing appropriate probes, i.e. plasmid DNA, sonicated calf thymus DNA and bovine serum albumin. In static binding studies performed with adsorbents that had been exposed to plasmas at the 5 g scale (25 g L⁻¹ of plasma reactor), the highest ‘surface/core’ modification selectivity was observed for Q HyperZ that had been subjected to 3 h of air plasma etching at 220 V (35.8 W L⁻¹). This treatment removed ∼53% of ‘surface’ DNA binding at the expense of a 9.3% loss in ‘core’ protein binding. Even more impressive results were obtained in dynamic expanded bed adsorption studies conducted with Q HyperZ adsorbents that had been treated with air (220 V, 3 h) and ‘vinyl acetate/argon’ (170 V, 3 h) plasmas at 10.5 g scale (52.5 g L⁻¹ of plasma reactor). Following both plasma treatments: the 10% breakthrough capacities of the modified Q HyperZ adsorbents towards ‘surface’ binding DNA probes dropped very significantly (30–85%); the DNA induced inter-particle cross-linking and contraction of expanded beds observed during application of sonicated DNA on native Q HyperZ was completely eradicated; but the ‘core’ protein binding performance remained unchanged cf. that of the native Q HyperZ starting material.     

Impact of the physical and topographical characteristics of adsorbent solid-phases upon the fluidised bed recovery of plasmid DNA from Escherichia coli lysates

A comparison is made of the performance of two types of adsorbent solid phases (commercially sourced Streamline composites and custom-assembled Zirblast pelliculates), derivatised with similar anion exchange chemistries and applied to the recovery of plasmid DNA from Escherichia coli extracts prepared by chemical lysis and coarse filtration. Streamline and Zirblast adsorbents were characterised by average particle diameters of 200 and 95 microm, densities of 1.16 and 3.85 g/m2, and small ion capacities of 170 and 8 micromol/ml settled adsorbent, respectively. Detailed analysis of products and impurities in a full operational cycle of adsorption, washing, pre-elution, elution and regeneration processes was enabled by the harnessing of a battery of analyses for nucleic acid and organic solute content of feedstocks and bed effluents exploiting ultra-violet spectrophotometry, agarose gel electrophoresis and specific reactions with the fluorescent probe PicoGreen. In comparative tests operated under near identical conditions, Streamline and Zirblast adsorbents exhibited plasmid recoveries of 76 and 90% of bound product characterised by purity ratios (relative PicoGreen and A254 estimates of mass) of 9 and 32, respectively. Conclusions are drawn regarding the specific impact of the physical and topographical characteristics of solid-phase geometry upon product throughput, achievable product purity, process time-scales and operational economics for the manufacture of plasmid DNA.     

Nucleic acid affinity of clustered-charge anion exchange adsorbents: effects of ionic strength and ligand density

In previous work we demonstrated the improved protein-binding capacity and selectivity of ion-exchange adsorbents displaying a "clustered" rather than random, distribution of surface charges. For example, anion-exchange adsorbents displaying 5 mM of positive charge in the form of 1 mM penta-argininamide show much higher affinity and capacity for alpha-lactalbumin than do adsorbents displaying the same 5 mM total charge in the form of single dispersed argininamide charges. We also found that clustered adsorbents selectively favor proteins with inherent charge clustering. In the present work, "clustered" penta-argininamide adsorbents showed DNA binding capacity comparable to that of conventional dispersed adsorbents with 10-100-fold higher ligand density. We also observed that at moderate ionic strength the DNA affinity of all adsorbents tested increased with salt while RNA affinity decreased, so that selectivity for DNA over RNA was enhanced as salt concentration increased.     

Superporous agarose anion exchangers for plasmid isolation

Superporous agarose beads have wide, connecting flow pores allowing large molecules such as plasmids to be transported into the interior of the beads by convective flow. The pore walls provide additional surface for plasmid binding thus increasing the binding capacity of the adsorbent. Novel superporous agarose anion exchangers have been prepared, differing with respect to bead diameter, superpore diameter and type of anion-exchange functional group (poly(ethyleneimine) and quaternary amine). The plasmid binding capacities were obtained from breakthrough curves and compared with the binding capacity of homogeneous agarose beads of the same particle size. Significantly, the smaller diameter superporous agarose beads were found to have four to five times higher plasmid binding capacity than the corresponding homogeneous agarose beads. The experimentally determined plasmid binding capacity was compared with the theoretically calculated surface area for each adsorbent and fair agreement was found. Confocal microscopy studies of beads with adsorbed, fluorescently labelled plasmids aided in the interpretation of the results. Superporous poly(ethyleneimine)-substituted beads with a high ion capacity (230 micromol/ml) showed a plasmid binding of 3-4 mg/ml adsorbent. Superporous quaternary amine-substituted beads had a lower ion capacity (81 micromol/ml) and showed a correspondingly lower plasmid binding capacity (1-2 mg/ml adsorbent). In spite of the lower capacity, the beads with quaternary amine ligand were preferred, due to their much better plasmid recovery (70-100% recovery). Interestingly, both capacity and recovery was improved when the plasmid adsorption step was carried out in the presence of a moderate salt concentration. The most suitable superporous bead type (45-75 microm diameter beads; 4 microm superpores; quaternary amine ligand) was chosen for the capture of plasmid DNA from a clarified alkaline lysate. Two strategies were evaluated, one with and one without enzymatic digestion of RNA. The strategy without RNase gave high plasmid recovery, quantitative removal of protein and a 70% reduction in RNA.     

Direct recovery of recombinant nucleocapsid protein of Nipah virus from unclarified Escherichia coli homogenate using hydrophobic interaction expanded bed adsorption chromatography

A direct recovery of recombinant nucleocapsid protein of Nipah virus (NCp-NiV) from crude Escherichia coli (E. coli) homogenate was developed successfully using a hydrophobic interaction expanded bed adsorption chromatography (HI-EBAC). The nucleic acids co-released with the recombinant protein have increased the viscosity of the E. coli homogenate, thus affected the axial mixing in the EBAC column. Hence, DNase was added to reduce the viscosity of feedstock prior to its loading into the EBAC column packed with the hydrophobic interaction chromatography (HIC) adsorbent. The addition of glycerol to the washing buffer has reduced the volume of washing buffer applied, and thus reduced the loss of the NCp-NiV during the washing stage. The influences of flow velocity, degree of bed expansion and viscosity of mobile phase on the adsorption efficiency of HI-EBAC were studied. The dynamic binding capacity at 10% breakthrough of 3.2 mg/g adsorbent was achieved at a linear flow velocity of 178 cm/h, bed expansion of two and feedstock viscosity of 3.4 mPa s. The adsorbed NCp-NiV was eluted with the buffer containing a step gradient of salt concentration. The purification of hydrophobic NCp-NiV using the HI-EBAC column has recovered 80% of NCp-NiV from unclarified E. coli homogenate with a purification factor of 12.5.