An acidic cellulose–chitin hybrid gel as novel electrolyte for an electric double layer capacitor

A novel acidic cellulose–chitin hybrid gel electrolyte including binary ionic liquids (ILs) with an aqueous H₂SO₄ solution was prepared for an electric double layer capacitor (EDLC). Its electrochemical characteristics were investigated by galvanostatic charge–discharge measurements. The test cell with a hybrid gel electrolyte shows a specific capacitance of 162 F g^?1 at room temperature, which is higher than that for a cell with an H₂SO₄ electrolyte, 155 F g^?1. This hybrid gel electrolyte exhibits excellent high-rate discharge capability in a wide range of current densities as well as an aqueous H₂SO₄ solution. The discharge capacitance of the test cell can retain over 80% of its initial value in 100,000 cycles even at a high current density of 5000 mA g^?1.     

Worm-like mesoporous carbon synthesized from metal–organic coordination polymers for supercapacitors

A green and efficient route has been employed to synthesize a worm-like mesoporous carbon with high specific surface area (2587 m² g^?1) and large pore volume (3.14 cm³ g^?1). Three electrochemical methods have been used to measure its electrochemical performance. Worm-like mesoporous carbon performs the high specific capacitance (344 F g^?1) at constant-current densities of 50 mA g^?1.     

An activated carbon with high capacitance from carbonization of a resorcinol–formaldehyde resin

A polymeric activated carbon (PAC) was synthesized from the carbonization of a resorcinol–formaldehyde resin with KOH served as an activation agent. The nitrogen adsorption–desorption at 77 K, X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) were used to characterize the prepared PAC. Compared with the commercial activated carbon (Maxsorb: Kansai, Japan), PAC shows superior capacitive performance in terms of specific capacitance, power output and high energy density as electrode materials for supercapacitors. PAC presents a high specific capacitance of 500 F g^?1 in 6 mol l^?1 KOH electrolyte at a current density of 233 mA g^?1 which remained 302 F g^?1 even at a high current density of 4.6 A g^?1. The good electrochemical performance of the PAC was ascribed to well-developed micropores smaller than 1.5 nm, the presence of electrochemically oxygen functional groups and low equivalent series resistance.     

Superabsorbent polymer binder for achieving MnO2 supercapacitors of greatly enhanced capacitance density

One common dilemma encountered in designing a supercapacitor electrode is that the specific capacitance (C_s) of the active material decreases significantly as the active-material loading (mass area^? 1) increases. As a result, the geometric capacitance density (GCD; Farad area^? 1) of the electrode does not scale up linearly but gradually levels off with increasing loading. For MnO₂ supercapacitors, this problem has been solved to a great extent by introducing a superabsorbent polymer (SAP) binder, namely polyacrylic acid (PAA), to form composite particles with MnO₂. Other than acting as a binder to bound together MnO₂ particles, the SAP is believed to facilitate distribution of electrolyte throughout the active layer owing to its electrolyte-absorbing and swelling behaviors. The C_s of MnO₂ remains almost unchanged as the oxide loading varies over a wide range (1.5–6.5 mg cm^? 2) of heavy active-material loading. In addition, putting PAA throughout the entire active layer helps to magnify the specific interaction between PAA and MnO₂ that is known to enhance the capacitance of individual MnO₂ particles. The success in combining both high C_s and high active-material loading results in GCD of ca. 1.8–1.4 F cm^? 2 even under very high current densities (ca. 35–260 mA cm^? 2 or 5–40 A g^? 1-MnO₂).     

Achieving high electrode specific capacitance with materials of low mass specific capacitance: Potentiostatically grown thick micro-nanoporous PEDOT films

Electrode materials for supercapacitors are at present commonly evaluated and selected by their mass specific capacitance (C_M, F g⁻¹). However, using only this parameter may be a misleading practice because the electrode capacitance also depends on kinetics, and may not increase simply by increasing material mass. It is therefore important to complement C_M by the practically accessible electrode specific capacitance (C_E, F cm⁻²) in material selection. Poly[3,4-ethylene-dioxythiophene] (PEDOT) has a mass specific capacitance lower than other common conducting polymers, e.g. polyaniline. However, as demonstrated in this communication, this polymer can be potentiostatically grown to very thick films (up to 0.5 mm) that were porous at both micro- and nanometer scales. Measured by both cyclic voltammetry and electrochemical impedance spectrometry, these thick PEDOT films exhibited electrode specific capacitance (C_E, F cm⁻²) increasing linearly with the film deposition charge, approaching 5 F cm⁻², which is currently the highest amongst all reported materials.     

Synthesis of Co-containing mesoporous carbon foams using a new cobalt-oxo cluster as a precursor

A novel trinuclear cobalt-oxo cluster 2[Co₃O(Ac)₆(H₂O)₃]·H₂O (Co-OXO) has been obtained and characterized by X-ray single-crystal diffraction and elemental analysis. The structure of Co-OXO displays 3D supramolecular networks through hydrogen bonds and generates boron nitride (bnn) topology. Co-OXO was further used as a precursor to synthesize Co-containing mesoporous carbon foams (Co-MCFs), which exhibit highly ordered mesostructure with specific surface area of 614 m² g^?1 and uniform pore size of 2.7 nm. Charge–discharge tests show that the specific discharge capacitance of Co-MCFs is 7% higher than that of the MCFs at the current density of 100 mA g^?1, and 26% higher than that of MCFs at the current density of 3 A g^?1. The electrochemical behaviors of Co-MCFs are obviously improved due to the improved wettability, increased graphitization degree and the pseudo-capacitance through additional faradic reactions arising from cobalt.     

Preparation of monodisperse carbon nanospheres for electrochemical capacitors

The efficiently hydrothermal route using sucrose without any catalysts is employed to prepare the uniform carbon spheres. The monodisperse 100–150 nm carbon spheres are obtained with the activation treatment in molten KOH. The carbon spheres are characterized by transmission electron microscope, X-ray diffraction, N₂ adsorption, Raman spectroscopy and electrochemical techniques. The relationships of specific capacitance and surface properties of carbon spheres are investigated. A single electrode of carbon nanosphere materials performs excellent specific capacitance (328 F g⁻¹), area capacitance (19.2 μF cm⁻²) and volumetric capacitance (383 F cm⁻³).     

Double-layer capacitance of waste coffee ground activated carbons in an organic electrolyte

Using ZnCl₂ activation we prepared a series of carbon electrodes from waste coffee grounds to study the effect of mesopores on double-layer capacitance in a tetraethyl ammonium tetrafluoroborate/acetonitrile electrolyte. The activated carbon with the largest mesopore volume achieved an energy density of 34 Wh kg^?1 at low current loads, and significantly retained an energy density of 16.5 Wh kg^?1 and specific capacitance of more than 100 F g^?1 at fast charge–discharge rates (20 A g^?1). The effect of mesopores on capacitance at fast charge–discharge rates is discussed.     

Bi2O3 deposited on highly ordered mesoporous carbon for supercapacitors

A simple route has been employed to prepare nanosized Bi₂O₃ deposited on highly ordered mesoporous carbon. The electrochemical measurements reveal that, by loading only 10% Bi₂O₃ on the mesoporous carbon, the specific capacitance of the composite is improved by 62%, with the maximum value reaching 232 F g^?1 at a sweep rate of 5 mV s^?1. The specific capacitance of Bi₂O₃ is calculated and reaches 1305 F g^?1 at 1 mV s^?1. It is found that the mass transfer in the framework of the crystalline oxide is still difficult in spite of its nanosize, as evidenced by the decline of the specific capacitance of the Bi₂O₃ with the increase of the sweep rate. The cyclic life of composite materials is also measured and the capacitance only declines 21% after 1000 cycles.     

Electrochemical supercapacitor application of pervoskite thin films

We have explored electrochemically deposited pervoskite nanocrystalline porous bismuth iron oxide (BiFeO₃) thin film electrode from alkaline bath for electrochemical supercapacitors. The pervoskite BiFeO₃ nanocrystalline thin film electrode showed comparable specific capacitance of 81 F g⁻¹ and electrochemical supercapacitive performance and stability in an aqueous NaOH electrolyte to that of commonly used ruthenium based pervoskites.     

Potentiostatically deposited nanostructured α-Co(OH)2: A high performance electrode material for redox-capacitors

A high specific capacitance was obtained for α-Co(OH)₂ potentiostatically deposited onto a stainless-steel electrode in 0.1 M Co(NO₃)₂ electrolyte at −1.0 V vs. Ag/AgCl. The structure and surface morphology of the obtained α-Co(OH)₂ were studied by using X-ray diffraction analysis and scanning electron microscopy. A network of nanolayered α-Co(OH)₂ sheets was obtained; the average thickness of individual α-Co(OH)₂ sheets was 10 nm, and the thickness of the deposit was several micrometers. The capacitive characteristics of the α-Co(OH)₂ electrodes were investigated by means of cyclic voltammetry and constant current charge–discharge cycling in 1 M KOH electrolyte. A specific capacitance of 860 F g⁻¹ was obtained for a 0.8 mg cm⁻² α-Co(OH)₂ deposit. The specific capacitance did not decrease significantly for the active mass loading range of 0.1–0.8 mg cm⁻² due its layered structure, which allowed easy penetration of electrolyte and effective utilization of electrode material even at a higher mass. This opens up the possibility of using such materials in supercapacitor applications.     

Enhanced supercapacitive behaviors of birnessite

The birnessite type manganese dioxide electrode was prepared by the electrochemical stimulation as we recently described. It showed 190 F g⁻¹ in a Na₂SO₄ aqueous solution between −0.1 and 0.9 V versus Ag/AgCl at 1 A g⁻¹. The specific capacitance of birnessite was decreased by the manganese dissolution when the reduction and oxidation were repeated. By adding small amounts of Na₂HPO₄ or NaHCO₃ into the electrolyte, the capacitance increased to 200–230 F g⁻¹ and the manganese dissolution was successfully suppressed. Thanks to the additives, the birnessite demonstrated the much improved cycleability over >1800 cycles.     

Insoluble metal hexacyanoferrates as supercapacitor electrodes

Nano-sized insoluble iron, cobalt and nickel hexacyanoferrates (Mhcf) were prepared by a simple co-precipitation method. The potential of using these materials for supercapacitor was examined by cyclic voltammogram and constant charge/discharge. Due to the different types of the second metal (M), the Mhcf electrodes showed different electrochemical capacitive performances. The specific discharge capacitances of Fehcf, Nihcf and Cohcf electrodes at the current density of 0.2 A g⁻¹ were 425 F g⁻¹, 574.7 F g⁻¹ and 261.56 F g⁻¹, respectively. Meanwhile, the Mhcf electrodes showed good cyclic performance.     

Structural and electrochemical properties of a porous nanostructured SnO2 film electrode for lithium-ion batteries

A B₂O₃-doped SnO₂ thin film was prepared by a novel experimental procedure combining the electrodeposition and the hydrothermal treatment, and its structure and electrochemical properties were investigated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) analysis, energy dispersive X-ray (EDX) spectroscopy and galvanostatic charge–discharge tests. It was found that the as-prepared modified SnO₂ film shows a porous network structure with large specific surface area and high crystallinity. The results of electrochemical tests showed that the modified SnO₂ electrode presents the largest reversible capacity of 676 mAh g^?1 at the fourth cycle, close to the theoretical capacity of SnO₂ (790 mAh g^?1); and it still delivers a reversible Li storage capacity of 524 mAh g^?1 after 50 cycles. The reasons that the modified SnO₂ film electrode shows excellent electrochemical properties were also discussed.     

Highly mesoporous and high surface area carbon: A high capacitance electrode material for EDLCs with various electrolytes

Activated carbon fibers (ACFs) with high surface area and highly mesoporous structure for electrochemical double layer capacitors (EDLCs) have been prepared from polyacrylonitrile fibers by NaOH activation. Their unique microstructural features enable the ACFs to present outstanding high specific capacitance in aqueous, non-aqueous and novel ionic liquid electrolytes, i.e. 371 F g⁻¹ in 6 mol L⁻¹ KOH, 213 F g⁻¹ in 1 mol L⁻¹ LiClO₄/PC and 188 F g⁻¹ in ionic liquid composed of lithium bis(trifluoromethane sulfonyl)imide (LiN(SO₂CF₃)₂, LiTFSI) and 2-oxazolidinone (C₃H₅NO₂, OZO), suggesting that the ACF is a promising electrode material for high performance EDLCs.     

Macroporous Co3O4 platelets with excellent rate capability as anodes for lithium ion batteries

This paper reports the microwave-assisted synthesis of Co₃O₄ nanomaterials with different morphologies including nanoparticles, rod-like nanoclusters and macroporous platelets. The new macroporous platelet-like Co₃O₄ morphology was found to be the best suitable for reversible lithium storage properties. It displayed superior cycling performances than nanoparticles and rod-like nanoclusters. More interestingly, excellent high rate capabilities (811 mAh g^?1 at 1780 mA g^?1 and 746 mAh g^?1 at 4450 mA g^?1) were observed for macroporous Co₃O₄ platelet. The good electrochemical performance could be attributed to the unique macroporous platelet structure of Co₃O₄ materials.     

Fabrication and electrochemical properties of the Sn–Ni–P alloy rods array electrode for lithium-ion batteries

A new ternary Sn–Ni–P alloy rods array electrode for lithium-ion batteries is synthesized by electrodeposition with a Cu nanorods array structured foil as current collector. The Cu nanorods array foil is fabricated by heat treatment and electrochemical reduction of Cu(OH)₂ nanorods film, which is grown directly on Cu substrate through an oxidation method. The Sn–Ni–P alloy rods array electrode is mainly composed of pure Sn, Ni₃Sn₄ and Ni–P phases. The electrochemical experimental results illustrate that the Sn–Ni–P alloy rods array electrode has high reversible capacity and excellent coulombic efficiency, with an initial discharge capacity and charge capacity of 785.0 mAh g^?1 and 567.8 mAh g^?1, respectively. After the 100th discharge–charge cycling, capacity retention is 94.2% with a value of 534.8 mAh g^?1. The electrode also performs with an excellent rate capacity.     

MnO2 multilayer nanosheet clusters evolved from monolayer nanosheets and their predominant electrochemical properties

MnO₂ multilayer nanosheet clusters were prepared via electrochemical deposition route, which shows simpleness and high efficiency. The growth process of MnO₂ multilayer nanosheet clusters was investigated in this paper. The deposited MnO₂ films were characterized by XRD, SEM, TEM, and XPS. In addition, it was also electrochemically characterized by cyclic voltammetry in 1.0 M Na₂SO₄ electrolyte. The MnO₂ multilayer nanosheet clusters show a big specific capacitance, and it can be achieved about 521.5 F g^?1 at 5 mV s^?1. These materials also have a high electrochemical stability.     

Nanoporous carbon electrode from waste coffee beans for high performance supercapacitors

Activated carbon was produced from waste coffee grounds by treatment with ZnCl₂. Supercapacitor electrodes prepared from this coffee grounds carbon exhibited energy densities up to 20 Wh kg⁻¹ in 1 M H₂SO₄, and excellent stability at high charge–discharge rates. In a two-electrode cell a specific capacitance as high as 368 F g⁻¹ was observed, with rectangular cyclic voltammetry curves and stable performance over 10,000 cycles at a cell potential of 1.2 V and current load of 5 A g⁻¹. The good electrochemical performance of the coffee grounds carbon was attributed to a well developed porosity, with a distribution of micropores and mesopores 2–4 nm wide, and the presence of electrochemically active quinone oxygen groups and nitrogen functional groups. This work highlights the potential to utilize waste biomass to produce electrode materials for cost-effective energy storage systems.     

Electrochemical characterization of vertical arrays of tin nanowires grown on silicon substrates as anode materials for lithium rechargeable microbatteries

Vertical arrays of one-dimensional tin nanowires on silicon dioxide (SiO₂)/silicon (Si) substrates have been developed as anode materials for lithium rechargeable microbatteries. The process is complementary metal-oxide-semiconductor (CMOS) compatible for fabricating on-chip microbatteries. Nanoporous anodized aluminum oxide (AAO) templates integrated on SiO₂/Si substrates were employed for fabrication of tin nanowires resulting in high surface area of anodes. The microstructure of these nanowire arrays was investigated by scanning electron microscopy and X-ray diffraction. The electrochemical tests showed that the discharge capacity of about 400 mA h g⁻¹ could be maintained after 15 cycles at the high discharge/charge rate of 4200 mA g⁻¹.