Investigation into the surface selective oxidation of dual‐phase steels by XPS,SAM and SIMS

Surface selective oxides created during continuous annealing (MnO, SiO₂, etc.) can have a deleterious effect on coating adhesion after hot‐dip galvanizing. Earlier research works have made it clear that increasing the annealing atmosphere oxidizing potential can alleviate the problem by reducing external surface selective oxidation. In the present study, increasing the water vapour content of the nitrogen–hydrogen protective gas mixture was used to raise its oxidizing potential. The technique was applied to a classical dual‐phase steel (0.15% C, 1.5% Mn, 0.45% Si, 0.05% Al…) that was annealed for 60 s at 800–810°C in protective atmospheres of nitrogen and 5% hydrogen with water vapour contents ranging from 10 to 6000 ppm. Post‐annealing surfaces were characterized by x‐ray photoelectron spectroscopy (XPS), secondary ion mass spectroscopy (SIMS) and scanning Auger microscopy (SAM). In situ XPS analyses were carried out right after simulation annealing in the preparation chamber connected to the spectrometer, never returning the specimens to air. This made it possible to identify in a reliable way the elements that segregated to the surface during the treatment, and to determine their corresponding oxidation states. On the other hand, the high sensitivity of SIMS was taken advantage of to assess oxide in‐depth concentration profiles (SiO₂, Al₂O₃, FeO) as a function of the annealing conditions, and SAM was used to characterize the corresponding oxide particle morphology. External selective oxidation was thus shown to decrease with increasing water vapour contents in the atmosphere (from 80 to 6000 ppm), whereas internal oxidation increases drastically to ～4 μm below the free surface. At 10 ppm of H₂O the oxygen partial pressure is very low and the external selective oxidation results in a thin, but almost complete, coverage of the steel surface. Consequently, metallic iron cannot be observed at the surface, thus hampering hot‐dip galvanizability, unless the water vapour content is raised to 6000 ppm. Various surface morphologies were observed and discussed. In the authors' opinion, basic investigations of this type are an indispensable first step to improving the response of highly alloyed steels (dual‐phase, TRIP) to hot‐dip galvanizing. Copyright © 2003 John Wiley & Sons, Ltd.     

Post‐oxidizing effects on surface characteristics of salt bath nitrocarburized AISI 02 tool steel type

The effect of post‐oxidizing treatment on the characteristics of modified surface layers produced by salt bath nitrocarburizing on the industrial American Iron and Steel Institute (AISI) 02 tool steel types is investigated. Nitrocarburizing treatment is performed for 6 h and 8 h at 570 °C and post‐oxidizing treatment for 30, 60 and 90 min at 520 °C, using argon–steam mixture. Formed layers are characterized by their basic properties such as thickness layer, depth, surface hardness and wear resistance. Detailed estimation of the modified metal surface quality, in terms of chemical composition, formed phases, microstructures and diffusion mechanisms are performed by metallographic techniques, EDX, X‐ray diffraction, scanning electron microscopy (SEM) and glow discharge optical electron spectroscopy (GDOES). The corrosion resistance was investigated in 0.4 M H₂SO₄ solutions, using steady‐state electrochemical polarization methods. The obtained results revealed the existence of a superficial oxide layer which consists of magnetite (Fe₃O₄) and hematite (Fe₂O₃) and the presence of an ε‐phase associated with a small amount of γ′‐phase. Important improvements in wear, microhardness and corrosion resistance occur after these treatments and it is specifically concluded that the sole application of a nitrocarburizing treatment does not significantly ameliorate the corrosion resistance of the as‐received steel. In fact, post‐oxidation treatment contributes to increase corrosion resistance by forming a dense magnetite layer and at the same time, it partially covers the compound layer pores. Copyright © 2009 John Wiley & Sons, Ltd.     

SIMS/XPS characterization of surface layers formed in 3 mass% Si‐steel by annealing in oxygen at low partial pressure

Selective oxidation in silicon steel shows several interesting phenomena, such as the formation of an internal oxidation zone that depends on the oxidation conditions and the steel composition. In this work, SIMS and XPS were used for characterizing the formation processes of surface layers formed during selective oxidation of a typical silicon steel. The starting material is a secondary‐recrystallized 3 mass% Si‐steel sheet with a surface orientation of (011). Sample sheets were annealed at a temperature of 948–1023 K under an atmosphere with a low partial pressure of oxygen. The SIMS depth profiles show that the internal oxidation zone thickens and an iron‐rich layer that formed on the internal oxidation zone expands as the annealing temperature increases. Manganese and chromium levels increase outside the internal oxidation zone, whereas tin exists in the internal oxidation zone. The XPS results of the sample surface show that silicon and manganese levels increase on the sample surface to form oxides, and the chemical composition and state of these elements depend on the annealing temperature. In addition, tin increases on the surface of a relatively thick iron‐rich layer that formed on the internal oxidation layer. These experimental results are discussed on the basis of the thermodynamic characteristics of the elements. Copyright © 2003 John Wiley & Sons, Ltd.     

Laser embedding of TiC particles into the surface of phosphor bronze‐bearing material

A carbon film containing 5% TiC particles is formed on a pre‐prepared bronze surface prior to laser treatment. The carbon film provides increased absorption of the incident laser beam and hosts TiC particles with a uniform distribution at the workpiece surface. Optical and scanning electron microscopy are used to examine the metallurgical and morphological changes in the laser treated layer. Micro‐hardness of the laser‐treated surface is measured, and the residual stress formed in the surface vicinity is measured using the X‐ray diffraction technique. It was found that a dense layer with fine grains was formed in the laser‐treated layer. The micro‐hardness of the laser‐treated surface increases almost three times compared with the base material hardness. The presence of a dense layer and the formation of Cu₃N in the surface region contribute to the hardness enhancement at the surface. Copyright © 2012 John Wiley & Sons, Ltd.     

Influence of thermal annealing on the microstructure,hardness and corrosion behavior of TiAlSiCuN nanocomposite films

Nanocomposite TiAlSiCuN films were deposited on high speed steels by filtered magnetic arc ion plating. Detailed properties of the films annealed at various temperatures are studied. After thermal annealing at different temperatures ranging from 400 to 800 °C, changes in the film micro‐structure, chemical and phase composition, surface morphology, hardness and polarization curve properties were systematically characterized by X‐ray diffraction, X‐ray photoelectron spectroscopy, scanning electron microscopy, nano‐indenter and electrochemical workstation, respectively. It was found that the TiAlSiCuN films could be fully oxidized at 800 °C, Al and Ti atoms all diffused outwards and formed dense protective Al₂O₃ and TiO₂ layer. Simultaneously, the TiAlN phase gradually disappeared. The films annealed at 400 °C obtained the highest hardness because of the certain grain growth and little generated oxides. Besides, the certain formation of dense protective Al₂O₃ layer made the TiAlSiCuN film annealed at 600 °C present the least corrosion current density and the corrosion voltage. Copyright © 2016 John Wiley & Sons, Ltd.     

A study on effects of TiB2 contents on reactive products and compressive strength of brazed CBN grains

The composite fillers were prepared by means of mixing Ag‐Cu‐Ti alloy and TiB₂ reinforcing particles. Experimental study was conducted on the chemical reaction and the reactive products at the interface between CBN grains and the composite filler. The compressive strength measurement of brazed CBN grains was performed. Results obtained show that the TiB₂particles disperse uniformly in the filler layer. Great influence of TiB₂particles is made on the quantity of the reactive products formed on the surface of brazed CBN grains. The destruction of the sharp edges of grains is restrained. Depending on the compact and fine reactive compounds, hard joining is realized for the CBN grain and the filler layer. When the content of TiB₂particles in the composite filler is 8 wt%, the thermal damage of the brazed CBN grains are controlled effectively. In this case the compressive strength of the brazed grains reaches 15.3 N, which is as high as that of the original ones. Copyright © 2009 John Wiley & Sons, Ltd.     

Characterization of chemical information and morphology for in‐depth oxide layers in decarburized electrical steel with glow discharge sputtering

A combination of scanning electron microscopy, X‐ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, and transmission electron microscopy with a sampling method by glow discharge sputtering was successfully employed to characterize the chemical information and microscopic features of oxide layers formed during decarburization annealing of electrical steel in the depth direction at high resolution. The discontinuous surface oxides consisted of SiO₂, (Fe,Mn)SiO₃/(Fe,Mn)₂SiO₄, and FeO. SiO₂ embedded in the (Fe,Mn)₂SiO₄ at the surface may be developed by the preferential nucleation and growth kinetics. The discrete or often relatively spherical oxides of internal oxidation by the energetically favorable surface effect were identified as a mixture of SiO₂ and (Fe,Mn)₂SiO₄ at a depth of ~0.5 µm from the surface. The oxides of networks and small particles at a depth greater than ~1 µm were solely silica, of which the morphologies were possibly caused by the enhanced diffusion of oxygen atoms and Si atoms at grain boundaries or sub‐grain boundaries. The equilibrium and kinetic considerations served by theoretical calculations were introduced to understand the formation and behavior of the observed in‐depth oxidation. Copyright © 2013 John Wiley & Sons, Ltd.     

Carpetlike dense‐layer formation in a polyelectrolyte brush at the air/water interface

A carpetlike dense‐layer formation between a hydrophobic layer and a polyelectrolyte brush layer has been found in the monolayers of an ionic amphiphilic diblock copolymer, poly(1,1‐diethylsilacyclobutane)_m‐block‐poly(methacrylic acid)_n, on a water surface by an X‐ray reflectivity technique. By detailed analysis, we have found that the hydrophilic layer under the water is not a simple layer but is divided into two layers, that is, a carpetlike dense methacrylic acid (MAA) layer near the hydrophobic layer and a polyelectrolyte brush layer. We have also confirmed that a well‐established polyelectrolyte brush is formed only for the m:n = 43:81 polymer monolayer: For m:n = 40:10 and m:n = 45:60 polymer monolayers, only a dense MAA layer is formed. This dense‐layer formation should be the origin of the interesting hydrophobic‐layer thickness variation previously reported; The hydrophobic‐layer thickness takes a minimum as a function of the hydrophilic chain length at any surface pressure studied. An overview of the data for three samples with different chain lengths (m:n = 40:10, 45:60, or 43:81) has shown that the thickness of this dense layer is 10–20 Å and is independent of the surface pressure and polymerization degree of poly(methacrylic acid) (PMAA) in the range studied. This dense‐layer formation is explained by the reasonable speculation that contact with PMAA is thermodynamically more stable than direct contact with water for the diethylsilacyclobutane (Et₂SB) layer on water. In this sense, the dense layer acts like a carpet for the hydrophobic Et₂SB layer, and a 10–20‐Å thickness could be a critical value for the carpet. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1921–1928, 2003     

Nitrogen uptake of nickel free austenitic stainless steel powder during heat treatment—an XPS study

In austenitic stainless steel nitrogen stabilizes the austenitic phase, improves the mechanical properties and increases the corrosion resistance. Nitrogen alloying enables to produce austenitic steels without the element nickel which is high priced and classified as allergy inducing. A novel production route is nitrogen alloying of CrMn‐prealloyed steel powder via the gas phase. This is beneficial as the nitrogen content can be adjusted above the amount that is reached during conventional casting. A problem which has to be overcome is the oxide layer present on the powder surface which impedes both the sintering process and the uptake of nitrogen. This study focuses on whether heat treatment under pure nitrogen is an appropriate procedure to enable sintering and nitrogen uptake by reduction of surface oxides. X‐ray photoelectron spectroscopy (XPS) in combination with scanning electron microscopy (SEM) and energy dispersive X‐ray spectrometry (EDS) are used to investigate the surface of powdered FeMn19Cr17C0.4N heat treated under nitrogen atmosphere. The analyses showed reduction of iron oxides already at 500 °C leading to oxide‐free metallic surface zones. Mn and Cr oxides are reduced at higher temperatures. Distinct nitrogen uptake was registered, and successful subsequent sintering was reached. Copyright © 2014 John Wiley & Sons, Ltd.     

“Smart” molecularly imprinted monoliths for the selective capture and easy release of proteins

A new thermally switchable molecularly imprinted monolith for the selective capture and release of proteins has been designed. First, a generic poly(glycidyl methacrylate‐co‐ethylene dimethacrylate) monolith reacted with ethylenediamine followed by functionalization with 2‐bromoisobutyryl bromide to introduce the initiator for atom transfer radical polymerization. Subsequently, a protein‐imprinted poly(N‐isopropylacrylamide) layer was grafted onto the surface of the monolithic matrix by atom transfer radical polymerization. Scanning electron microscopy and energy‐dispersive X‐ray spectroscopy of the cross‐sections of imprinted monoliths confirmed the formation of dense poly(N‐isopropylacrylamide) brushes on the pore surface. The imprinted monolith exhibited high specificity and selectivity toward its template protein myoglobin over competing proteins and a remarkably large maximum adsorption capacity of 1641 mg/g. Moreover, this “smart” imprinted monolith featured thermally responsive characteristics that enabled selective capture and easy release of proteins triggered only by change in temperature with water as the mobile phase and avoided use of stronger organic solvents or change in ionic strength and pH.     

Laser surface treatment of high‐speed steel: presence of TiC particles at the surface

Laser treatment of a high‐speed steel surface is carried out and metallurgical and morphological changes in the laser‐treated layer are examined using SEM, EDS and XRD. A carbon film of 50 µm thickness and containing 5% TiC particles is formed at the workpiece surface prior to the laser treatment process. The carbon film formed at the surface enhances the absorption of laser irradiation and retains TiC particles at the workpiece surface. The residual stress formed at the laser‐treated surface is determined using the XRD technique while the indentation tests are carried out to measure microhardness and fracture toughness of the resulting surface. It is found that ε‐Fe₃N, and ε‐Fe₃ (N,C) compounds are formed at the laser‐treated surface, which are attributed to the presence of carbon film and high‐pressure nitrogen‐assisting gas. The fracture toughness of the laser‐treated surface reduces because of the increased hardness and dense layer formed at the surface vicinity. Copyright © 2011 John Wiley & Sons, Ltd.     

Characterization of wet‐etched GaAs (100) surfaces

To enable the use of GaAs‐based devices as chemical sensors, their surfaces must be chemically modified. Reproducible adsorption of molecules in the liquid phase on the GaAs surfaces requires controlled etching procedures. Several analytical methods were applied, including Fourier transform infrared spectroscopy (FTIRS) in attenuated total reflection and multiple internal reflection mode (ATR/MIR), high‐resolution electron energy loss spectroscopy (HREELS), X‐ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM) for the analysis of GaAs (100) samples treated with different wet‐etching procedures. The assignment of the different features due to surface oxides present in the vibrational and XPS spectra was made by comparison with those of powdered oxides (Ga₂O₃, As₂O₃ and As₂O₅). The etching procedures here described, namely, those using low concentration HF solutions, substantially decrease the amount of arsenic oxides and aliphatic contaminants present in the GaAs (100) surfaces and completely remove gallium oxides. The mean thickness of the surface oxide layer drops from 1.6 nm in the raw sample to 0.1 nm after etching. However, in presence of light, water dissolution of arsenic oxides is enhanced, and oxidized species of gallium cover the surface. Copyright © 2005 John Wiley & Sons, Ltd.     

XPS depth profile study of porous zirconia films deposited on stainless steel by spray pyrolysis: the problem of substrate corrosion

Zirconia (ZrO₂) films of tissue‐like structure and narrow pore size distribution have been deposited by spray pyrolysis using aqueous zirconyl chloride octahydrate (ZrOCl₂·8H₂O) precursor solutions. Stainless‐steel sheets, protected or unprotected by a ZnO barrier layer, have been used as the substrate material held at 473 K. The ZnO barrier layers have been deposited on the stainless steel held at 523 K by spray pyrolysis using a zinc acetate precursor. Their property of corrosion protection to stainless steel has been proved by electrochemical polarization measurements in 0.5 M NaCl solution. A complementary study of XPS (depth profiling, mapping) and x‐ray diffraction has shown that the unprotected steel substrates were corroded during ZrO₂ film post‐annealing in air at T ≥ 773 K, whereas steel substrates protected with a compact barrier layer of crystalline ZnO before ZrO₂ film deposition did not show surface corrosion even after annealing up to 997 K. Copyright © 2004 John Wiley & Sons, Ltd.     

Ultrafine grain formation and coating mechanism arising from a blast coating process: A transmission electron microscopy analysis

This article examines the substrate/coating interface of a coating deposited onto mild steel and stainless steel substrates using an ambient temperature blast coating technique known as CoBlast. The process uses a coincident stream of an abrasive blast medium and coating medium particles to modify the substrate surface. The hypothesis for the high bond strength is that the abrasive medium roughens the surface while simultaneously disrupting the passivating oxide layer of the substrate, thereby exposing the reactive metal that then reacts with the coating medium. The aim of this study is to provide greater insight into the coating/substrate bonding mechanism by analysing the interface between a hydroxyapatite coating on both mild and stainless steel substrates. The coating adhesion was measured via a tensile test, and bond strengths of approximately 45 MPa were measured. The substrate/coating interface was examined using transmission electron microscopy and selected area diffraction. The analysis of the substrate/coating interface revealed the presence of ultrafine grains in both the coating and substrate at interface associated with deformation at the interface caused by particle impaction during deposition. The chemical reactivity resulting from the creation of these ultrafine grains is proposed to explain the high adhesive strength of CoBlast coatings.     

The Role of Weak Interactions in the Mechano‐induced Single‐Crystal‐to‐Single‐Crystal Phase Transition of 8‐Hydroxyquinoline‐Based Co‐crystals

Mechano‐induced single‐crystal‐to‐single‐crystal (SCSC) phase transitions in crystalline materials that change their properties have received more and more attention. However, there are still too few examples to study molecular‐level mechanisms in the mechano‐induced SCSC phase transitions, making the systematic and in‐depth understanding very difficult. We report that bis‐(8‐hydroxyquinolinato) palladium(II)‐tetracyanoquinodimethane (PdQ₂‐TCNQ) and bis‐(8‐hydroxyquinolinato) copper(II)‐tetracyanoquinodimethane (CuQ₂‐TCNQ) show very different mechano‐response behaviors during the SCSC phase transition. Phase transition in CuQ₂‐TCNQ can be triggered by pricking on the crystal surface, while in PdQ₂‐TCNQ it can only be induced by applying pressure uniformly over the whole crystal face. The crystallography data and Hirshfeld surface analysis indicate that the weak intra‐layer C?H???O, C?H???N hydrogen bonds and inter‐layer stacking interactions determine the feasibility of the SCSC phase transition by mechanical stimuli. Weaker intra‐layer interactions and looser inter‐layer stacking make the SCSC phase transition occur much more easily in the CuQ₂‐TCNQ.     

Influence of hydrothermal exposure on surface characteristics and corrosion behaviors of anodized titanium

Titanium surface was modified by anodization in phosphoric acid solution at the voltages of 100 and 250 V, respectively. Surface characteristics and corrosion behaviors of anodized titanium were investigated before and after hydrothermal exposure in 3.5 wt.% NaCl solution at 160 °C for 24 h. It was found that anodization at 100 and 250 V resulted in the formation of a dense and a porous TiO₂ layer, respectively. The existence of anatase in the oxide layers of the 250‐V samples was confirmed by X‐ray diffraction analysis but not in the oxide layers of the 100‐V samples. After the hydrothermal exposure, the surface morphology of the 100‐V sample changed significantly, and discrete nanorods were formed on the surface. In contrast, the 250‐V sample basically preserved their original surface structures after the exposure except that numerous closely packed nanoparticles emerged on the surface. X‐ray diffraction analysis indicated that the exposure transformed the amorphous oxides into crystalline anatase. The corrosion behavior investigation of anodized titanium showed that the hydrothermal exposure had slight influence on the corrosion resistance of the 100‐V samples but decreased the corrosion resistance of the 250‐V samples significantly. Copyright © 2014 John Wiley & Sons, Ltd.     

New horizons in sputter depth profiling inorganics with giant gas cluster sources: Niobium oxide thin films

X‐ray photoelectron spectroscopy is used to study a wide variety of material systems as a function of depth (“depth profiling”). Historically, Ar⁺ has been the primary ion of choice, but even at low kinetic energies, Ar⁺ ion beams can damage materials by creating, for example, nonstoichiometric oxides. Here, we show that the depth profiles of inorganic oxides can be greatly improved using Ar giant gas cluster beams. For NbO_x thin films, we demonstrate that using Ar_x⁺ (x = 1000‐2500) gas cluster beams with kinetic energies per projectile atom from 5 to 20 eV, there is significantly less preferential oxygen sputtering than 500 eV Ar⁺ sputtering leading to improvements in the measured steady state O/Nb ratio. However, there is significant sputter‐induced sample roughness. Depending on the experimental conditions, the surface roughness is up to 20× that of the initial NbO_x surface. In general, higher kinetic energies per rojectile atom (E/n) lead to higher sputter yields (Y/n) and less sputter‐induced roughness and consequently better quality depth profiles. We demonstrate that the best‐quality depth profiles are obtained by increasing the sample temperature; the chemical damage and the crater rms roughness is reduced. The best experimental conditions for depth profiling were found to be using a 20 keV Ar₂₅₀₀⁺ primary ion beam at a sample temperature of 44°C. At this temperature, there is no, or very little, reduction of the niobium oxide layer and the crater rms roughness is close to that of the original surface.     

Turning Regioselectivity into Stereoselectivity: Efficient Dual Resolution of P‐Stereogenic Phosphine Oxides through Bifurcation of the Reaction Pathway of a Common Intermediate

Synthetic routes that provide facile access to either enantiomeric form of a target compound are particularly valuable. The crystallization‐free dual resolution of phosphine oxides that gives highly enantioenriched materials (up to 94 % ee) in excellent yields is reported. Both enantiomeric oxides have been prepared from a single intermediate, (R_P)‐alkoxyphosphonium chloride, which is formed in the course of a selective dynamic kinetic resolution using a single enantiomer of menthol as the chiral auxiliary. The origin of the dual stereoselectivity lies in bifurcation of the reaction pathway of this intermediate, which works as a stereochemical railroad switch. Under controlled conditions, Arbuzov‐type collapse of this intermediate proceeds through C O bond fission with retention of the configuration at the phosphorus center. Conversely, alkaline hydrolysis of the P O bond leads to the opposite S_P enantiomer.     

Wetting properties of polystyrene/divinylbenzene crosslinked porous polymers obtained using W/O highly concentrated emulsions as templates

Macroporous polystyrene/divinylbenzene (PS‐DVB) monoliths were obtained using highly concentrated W/O emulsions as templates. These monoliths are of interest due to the high potential applications for catalysis, scaffolds for tissue engineering, filters, membranes, or drug delivery systems. Dynamic wetting behavior through the polymer monolith is directly related to contact angle. For this reason, in this paper we investigate the relationship between contact angle, morphology, and chemical composition of the dense skin layer and the highly porous interior surface of PS‐DVB porous monoliths. Whereas the dense skin layer exhibits a Wenzel regime using water as wetting liquid, the highly porous interior surface exhibits a Cassie–Baxter regime. This behavior is correlated with the roughness observed by scanning electron microscopy (SEM). However, the observed contact angle hysteresis seems to indicate that factors other than surface roughness should be taken into account. For this reason, chemical composition was also studied by elemental microanalysis and X‐ray photoelectron spectroscopy (XPS). The differences in chemical composition observed between the dense skin layer and the highly porous interior surface, according to the wetting model for a heterogeneous surface proposed by Johnson and Dettre, seems also to contribute to the wetting hysteresis. The different wetting between the dense skin layer and the highly porous interior surface results in a dual wettability phenomenon, in which a liquid wets the dense skin layer and does not penetrate into the highly porous interior of the PS‐DVB monoliths. This phenomenon can be of relevance in absorption or desorption processes such as in drug delivery processes. Copyright © 2009 John Wiley & Sons, Ltd.     

The layer‐by‐layer stoichiometry of La0.7Sr0.3MnO3/SrTiO3 thin films and interfaces

By using a combination of synchrotron photoemission and a finite element model, the layer‐by‐layer stoichiometry of pulsed laser deposited La_0.7Sr_0.3MnO₃ (LSMO) thin films is extracted. For 3‐ and 5‐unit‐cell films, the LSMO stoichiometry at the LSMO/SrTiO₃ interface has been studied, and it is found that the Sr surface segregation is reversed at the lower interface such that it becomes La rich and Sr depleted. Mn is depleted throughout the entire layer, consistent with reports of a magnetically ‘dead’ layer and the formation of a Ruddlesden–Popper phase. The depth‐averaged Mn concentration is less than 50% of the expected value, suggesting that interface mixing or segregation into the bulk is important, whereas the depth‐averaged La and Sr concentrations are close to the expected values. Copyright © 2013 John Wiley & Sons, Ltd.