The effects of emulsifier type,phase ratio,and homogenization methods on stability of the double emulsion

The double emulsion technology has a potential effect on the development of diversity and quality of functional foods by means of decreasing oil or salt concentration, encapsulating and controlling release of valuable components. In this study, it was aimed to formulate stable double emulsions to be used in food systems. W1/O ratios of primary emulsions, stabilized by polyglycerol polyricinoleate (PGPR), were designed as 2:8 and 4:6, and (W1/O)/W2 ratios of the double emulsions were used as 2:8 and 4:6. W/O/W phase ratios, homogenization methods applied to primary emulsion (high-speed homogenization, ultrasonic homogenization), and emulsifier types used in W2 phase [sodium caseinate (SC), xanthan gum, lecithin-whey protein concentrate] were used as independent variables. Particle size and distributions, stability, encapsulation efficiency (EE), rheological properties, long-term stability, and morphological properties of the double emulsions were investigated.

The double emulsions prepared with SC and (W1/O)/W2 ratio of 4:6, were found to have the higher stability values, higher apparent viscosity, and lower particle size. High-speed homogenization applied to primary emulsion reduced particle size of the double emulsion and increased apparent viscosity, but did not affect stability and EE of the double emulsions, significantly.     

Stability and rheology of three types of W/O/W multiple emulsions emulsified with lecithin

Three types of multiple emulsions were prepared with lecithin. The morphology, stability, and rheological properties of the three types of W/O/W multiple emulsions were evaluated. The formulation factors, including salts and aliphatic alcohol, were further examined. The three types of multiple emulsions were formed by different emulsifiers. An excellent multiple emulsion occurred with 2?wt% lecithin concentration, stabilized by 0.05?wt% NaCl. All multiple emulsions showed shear-thinning behavior, i.e., the apparent viscosity decreased with the increase of the shear rate. With the high concentration of lecithin, the multiple emulsions exhibited the highest viscosity at low shear rate and had higher storage modulus (G′) and the loss modulus (G″). This study was conducted to reveal that different types of multiple emulsions can be formed with lecithin, and that the stability and rheological properties were different with different types of multiple emulsions.     

An Experimental Study on the Viscosity of Water-in-Oil Emulsions

Water-in-oil (W/O) emulsions are very common in the petroleum industry, and their viscosities are the principle parameters for the operation design. Typical correlations composed by one or two factors cannot always fit the apparent viscosity of W/O emulsions very well, especially when applied to the crude oil/water emulsions. The viscosities of W/O emulsions, which were made from three kinds of crude oil, were measured by Anton Paar MCR302 viscometer at atmospheric pressure with different temperatures as well as shear rates. The experiment results indicate that W/O emulsion would exhibit Newtonian characteristic when water content is no higher than 0.2 and non-Newtonian characteristic otherwise. According to the experimental data, a modified correlation based on the Broughton–Squires model and Ronningsen model was introduced to predict the viscosity of W/O emulsions, and the comparison results showed that the new modified correlation has better accuracy than the original models.     

Influence of composition on the encapsulation properties of P/O/W multiple emulsions for Vitamin C

Abstract

The aim of this work was to study the encapsulation properties of polyols-in-oil-in-water (P/O/W) multiple emulsions for Vitamin C (Vc). The influence of formulation factors, including the concentration of lipophilic emulsifier, hydrophilic emulsifier, salt and glycerol had been investigated. The results indicated that the encapsulation stability could be improved by increasing the lipophilic emulsifier concentration which could strengthen the interfacial film. In contrast, the excess of hydrophilic emulsifier destabilized the emulsion. The presence of glycerol in the outer aqueous phase accelerated the phase transfer, thus reduced the encapsulation rate. The addition of salt in inner polyols phase had little effect on encapsulation rate while markedly affected the morphology and stability of this system. P/O/W multiple emulsions showed better encapsulation stability than the W/O/W multiple emulsions as the former’s encapsulation rate could remain more than 75% after 2?weeks while the latter only remained less than 60%. Meanwhile, the P/O/W emulsions exhibited higher storage modulus (G’), bigger loss modulus (G’’) and broaden linear viscoelastic regions than W/O/W emulsions.     

Preparation of a stable double emulsion (W1/O/W2): role of the interfacial films on the stability of the system

This paper presents new protocols enabling preparation of W1/O/W2 double emulsions: one, using soybean oil as the O phase, that yields edible emulsions with industrial applications, and a second that yields emulsions with a previously unattainable concentration 15% (w/w) of surfactants in the external phase (the 15% target was chosen to meet the typical industry standard). Preparation of a stable W1/O emulsion was found to be critical for the stability of the system as a whole. Of the various low HLB primary surfactants tested, only cethyl dimethicone copolyol (Abil EM90), A-B-A block copolymer (Arlacel P135), and polyglycerol ester of ricinoleic acid (Grinstead PGR-90) yielded a stable W/O emulsion. Investigation of the surface properties of those surfactants using the monolayer technique found two significant similarities: (1) stable, compressible, and reversibly expandable monolayers; and (2) high elasticity and surface potential. The high degree of elasticity of the interfacial film between W1 and O makes it highly resilient under stress; its failure to break contributes to the stability of the emulsion. The high surface potential values observed suggest that the surfactant molecules lie flat at the O/W interfaces. In particular, in the case of PGR-90, the hydroxyl (-OH) groups on the fatty acid chains serve as anchors at the O/W interfaces and are responsible for the high surface potential. The long-term stability of the double emulsion requires a balance between the Laplace and osmotic pressures (between W1 droplets in O and between W1 droplets and the external aqueous phase W2). The presence of a thickener in the outer phase is necessary in order to reach a viscosity ratio (preferably approximately 1) between the W1/O and W2 phases, allowing dispersion of the viscous primary emulsion into the W2 aqueous phase. The thickener, which also serves as a dispersant and consequently prevents phase separation due to its thixotropic properties, must be compatible with the surfactants. Finally, the interactions between the low and high HLB emulsifiers at the O/W2 interface should not destabilize the films. It was observed that such destructive interaction for the system could be prevented by the use of two high HLB surfactants in the outer aqueous phase: an amphoteric surfactant, Betaine, and an anionic surfactant, sodium lauryl ether sulfate. The combination of such pairs of surfactants was found to contribute to the films' stability.     

W/O/W多重乳液中水传递的控制

建立了简化的W/O/W(水/油/水)多重乳液乳珠模型——统计平均半径模型, 预测出当W/O/W多重乳液内水相水滴之间以及内外水相之间均达到水传递平衡时的内外水相中盐的浓度, 从而实现对水传递的控制, 以维持W/O/W多重乳液的稳定. 按理论预测制备出了不同稳定态的W/O/W多重乳液, 利用差分扫描量热仪(DSC)检测了多重乳液中水的传递过程, 确定体系在实验状态下的稳定程度, 实验结果与理论预测基本吻合.     

Research on factors affecting heavy oil-in-water emulsion rheology and pressure drop

The effects of the types and contents of surfactants, alkali types and concentrations, oil-water ratios, mixing speeds, and emulsifying temperatures on the rheology of heavy oil-in-water (O/W) emulsions were studied. The experimental results showed that the apparent viscosity increased as the formulated surfactant content increased. The organic/inorganic alkali played a twofold role in the apparent viscosity of the O/W emulsion, promoting the ionization of these interfacial active components and compressing the diffused double layer, the competition of which determined whether the apparent viscosity increased or decreased. With increasing oil-water ratios, the apparent viscosity increased, whereas an increase in the emulsifying temperature resulted in a decrease of the apparent viscosity. When the mixing speed was increased from 500 to 1000?r/min, the apparent viscosity increased. However, the apparent viscosity changed minimally for mixing speeds in the range of 1000–1500?r/min. To further discuss the impacts of these factors on the emulsion rheology and pressure drop, the results of an orthogonal test were analyzed through ANOVA using SPSS software; the pressure drops in the samples were calculated using Matlab software. The results demonstrated that the effects of the oil-water ratios on emulsion viscosity and pressure drop were the most prominent.     

Stabilization of Water‐Soluble Antioxidant in Water‐in‐Oil‐in‐Water Double Emulsions

Abstract

In this study, we are introducing a method that can effectively stabilize antioxidants in water‐in‐oil‐in‐water (W/O/W) double emulsions. Preliminarily, stable W/O/W double emulsions were produced by manipulating the characteristics of internal aqueous phase via two‐stage emulsification, resulting consequently in the formation of fine internal water droplets in the dispersed oil droplets. From conductivity measurements that can determine the elution amount of internal aqueous phase, it was confirmed that the double emulsion stability could be improved by treating the internal aqueous phase with a hydroxypropyl‐beta‐cyclodextrin. In this study, kojic acid, 5‐hydroxy‐2‐(hydroxymethyl)‐4‐pyrone was selected as a model antioxidant. The stabilization of kojic acid was attempted by locating it in the internal water droplets of the stable W/O/W double emulsions. The stability of kojic acid in the double emulsion system could be maintained at 90% for 10 weeks at high temperature. We believe that these stable W/O/W double emulsions could be used meaningfully as a carrier for many unstable antioxidants.     

A Three-Step Model for Submicron W/O Emulsion Formation in a Transitional-Phase Inversion Process

A three-step model of the transitional phase inversion (TPI) process for the formation of water-in-oil (W/O) emulsions is presented. Three types of emulsions exist in an emulsification process at different oil–water ratios and hydrophilic–lipophilic balance (HLB). A stable W/O emulsion was obtained using Sorbitan oleate (Span 80) and polyoxyethylenesorbitan monooleate (Tween 80) with a specified HLB and oil volume fraction. Oil was added into water, which contained the water-soluble surfactant, to dissolve the oil-soluble surfactant. This route allowed TPI to occur, and an interesting emulsification process was observed by varying the HLB, which corresponded to the change in the oil–water ratio. Two types of emulsions in the emulsification process were found: transition emulsion 1 (W/O/W high internal phase emulsion) and target emulsion 2 (W/O emulsion with low viscosity). This study describes the changes that occurred in the emulsification process.     

三元复合驱碱/表面活性剂/聚合物模拟原油乳状液稳定动力学特性

基于两相分离的乳状液稳定模型,研究了三元复合驱模拟原油乳状液稳定动力学特性;通过液膜强度和油水界面张力探讨了碱/表面活性剂/聚合物对模拟原油乳状液稳定动力学特性的影响机理。 结果表明,乳状液稳定模型可以很好的评价乳状液的稳定性,并得到乳状液的稳定动力学特性;碱浓度小于900 mg/L有利于乳状液的稳定,碱浓度大于900 mg/L不利于乳状液的稳定;表面活性剂和聚合物浓度的增加使得形成的模拟原油乳状液更加稳定;模拟原油乳状液的稳定作用主要是通过碱、表面活性剂降低油水界面张力并增加油水界面膜强度,聚合物通过提高界面膜强度实现的,三者存在协同效应。     

Concentrated CO(2)-in-Water Emulsions with Nonionic Polymeric Surfactants

Concentrated CO(2)-in-water (C/W) emulsions are reported for amphiphiles containing alkylene oxide-, siloxane-, and fluorocarbon-based tails as a function of temperature and salinity. Poly(ethylene oxide)-b-poly(butylene oxide) (EO(15)-b-BO(12)) can emulsify up to 70% CO(2) with droplet sizes from 2 to 4 &mgr;m in diameter, as determined by video-enhanced microscopy. This emulsion is stable over 48 h against both flocculation and coalescence. In contrast, it is extremely difficult to form concentrated water-in-CO(2) (W/C) emulsions with surfactants containing alkylene oxide moieties due to limited solvation of such tails by CO(2). In several cases, C/W emulsions are formed even when the surfactant prefers CO(2). This violation of Bancroft's rule may be attributed in part to the low viscosity of the compressed CO(2), which governs several mass and momentum transport mechanisms relevant to emulsion formation and stabilization. For the first time, W/C microemulsions are observed in a system with a nonionic amphiphile, namely F(CF(2)CF(2))(3-8)CH(2)CH(2)O(CH(2)CH(2)O)(10-15)H. For the same system, the emulsion morphology changes from C/W to W/C as the temperature increases. The electrical conductivity of C/W emulsions is predicted successfully as a function of the dispersed phase volume fraction of CO(2) with Maxwell's theory for inhomogeneous systems. Copyright 2001 Academic Press.     

Laminar Flow Emulsification Process to Control the Viscosity Reduction of Heavy Crude Oils

The formation of heavy crude oil in water (O/W) emulsion by a low energy laminar controlled flow has been investigated. The emulsion was prepared in an eccentric cylinder mixer. Its geometry allows the existence of chaotic flows that are able to mix well highly viscous fluids. This new mixer design is used to produce high internal phase ratio emulsions for three oils: castor oil and two heavy crude oils of different initial viscosity (Zuata and Athabasca crude oils). The influence of the stirring conditions, geometrical parameters, and water volume fraction on the rheological properties of the resulting O/W emulsion is studied.     

Effect of Inorganic Solids,Wax to Asphaltene Ratio,and Water Cut on the Stability of Water-in-Crude Oil Emulsions

The formation of stable water-in-crude oil emulsions during petroleum production and refinery may create sever and costly separation problems. It is very important to understand the mechanism and factors contributing to the formation and stabilization of such emulsions for both great economic and environmental development. This article investigates some of the factors controlling the stability of water-in-crude oil emulsions formed in Burgan oil field in Kuwait. Water-in-crude oil emulsion samples collected from Burgan oil filed have been used to separate asphaltenes, resins, waxes, and crude oil fractions. These fractions were used to prepare emulsion samples to study the effect of solid particles (Fe₃O₄) on the stability of emulsions samples. Results indicate that high solid content lead to higher degree of emulsion stability. Stability of emulsion samples under various waxes to asphaltenes (W/A) ratios have also been tested. These tests showed that at low W/A content, the emulsions were very stable. While at a wax to asphaltene ratio above 1 to 1, the addition of wax reduced emulsion stability. Stability of emulsion samples with varying amount of water cut has also been investigated. Results indicated that stability and hence viscosity of emulsion increases as a function of increasing the water cut until it reaches the inversion point where a sharp decline in viscosity takes place. This inversion point was found to be approximately at 50% water cut for the crude oils considered in this study.     

Emulsifying potency of new amino acid-type surfactant (II): stable water-in-oil (W/O) emulsions containing 85 wt% inner water phase

The ternary phase diagram for N-[3-lauryloxy-2-hydroxypropyl]-L-arginine L-glutamate (C12HEA-Glu), a new amino acid-type surfactant, /oleic acid (OA)/water system was established. The liquid crystal and gel complex formations between C12HEA-Glu and OA were applied to a preparation of water-in-oil (W/O) emulsions. Stable W/O emulsions containing liquid paraffin (LP) as the oil and a mixture of C12HEA-Glu and OA as the emulsifier were formed. The preparation of stable W/O emulsions containing 85 wt% water phase was also possible, in which water droplets would be polygonally transformed and closely packed, since the maximum percentage of inner phase is 74% assuming uniformly spherical droplets. Water droplets would be taken into the liquid crystalline phase (or the gel complex) and the immovable water droplets would stabilize the W/O emulsion system. The viscosity of emulsions abruptly increased above the 75 wt% water phase (dispersed phase). The stability of W/O emulsions with a lower weight ratio of OA to C12HEA-Glu and a higher ratio of water phase was greater. This unusual phenomenon may be related to the formation of a liquid crystalline phase between C12HEA-Glu and OA, and the stability of the liquid crystal at a lower ratio of oil (continuous phase). W/O and oil-in-water (O/W) emulsions containing LP were selectively prepared using a mixture of C12HEA-Glu and OA since the desirable hydrophile-lipophile balance (HLB) number for the emulsification was obtainable by mixing the two emulsifiers.     

Phase Transitions in Emulsions Formed by Aqueous Emulsifier and its Action on Improving Mobility in Oil Recovery

Transition from oil-in-water (O/W) emulsions to water-in-oil (W/O) emulsions and its action on enhanced oil recovery was investigated by viscosity, morphology, and simulated flooding experiments. This transition can be realized by increasing the volume ratio of oil to water or decreasing the emulsifier concentration. At a mass concentration of 0.3 wt%, the self-developed emulsifier FJ-1 mainly forms O/W emulsions at a volume ratio (oil to water) of 1:1. The emulsions behave as O/W emulsions with a low viscosity when the volume ratio of oil to water is below 2:1. Above 2:1, increasing volume ratio leads to the O/W emulsions transferring into W/O emulsions with high viscosity. For example, at a volume fraction of 4:1, the viscosity of W/O emulsions reaches 229.1 mPa · s, and separated water can hardly be detected. Transition from O/W emulsions to W/O emulsions with high viscosity can also be realized by decreasing the concentration of emulsifier to 0.05 wt% or lower at a volume ratio of 1:1. These may be the critical factors leading to transition from O/W emulsions to W/O emulsions at core conditions. Simulated flooding experiments show that emulsifier fluids can act as an in situ mobility improver and make an improvement of oil recovery even by 20.4%. The results indicate that the water-in-crude-oil emulsions possess great potential in enhancing oil recovery.     

Characterization of different double-emulsion formulations based on food-grade emulsifiers and stabilizers

This study focused on the preparation and characterization of water-in-oil-in-water (W1/O/W2)-type double emulsions designed by food-grade emulsifiers and stabilizers. The primary objective of this study was to compare different emulsion formulations in terms of droplet size, rheology, and stability and to reduce the amount of polyglycerol poliricinoleate (PGPR). To achieve these goals, PGPR and a PGPR–lecithin blend were utilized in the formation of the primary phase (W1/O), while varying concentrations of guar gum (GG) and gum tragacanth (GT) incorporated in the secondary water phase (W2). Shear thinning behavior was observed for all emulsion formulations. Sauter mean diameters of the emulsions prepared with PGPR as a hydrophobic emulsifier ranged between 30?µm and 75?µm, while those prepared with the PGPR–lecithin blend varied between 25?µm and 85?µm based on the first day’s measurements. In emulsions with the PGPR–lecithin blend, the smallest droplet size was obtained when the GG–GT blend was incorporated in the external aqueous phase. Moreover, GG–GT blends had high consistency coefficients and high apparent viscosity values. It was also observed that PGPR–lecithin containing emulsions were more stable.     

Interface composition of multiple emulsions: rheology as a probe

We have investigated the dynamic rheological properties of concentrated multiple emulsions to characterize their amphiphile composition at interfaces. Multiple emulsions (W1/O/W2) consist of water droplets (W1) dispersed into oil globules (O), which are redispersed in an external aqueous phase (W2). A small-molecule surfactant and an amphiphilic polymer were used to stabilize the inverse emulsion (W1 in oil globules) and the inverse emulsion (oil globules in W2), respectively. Rheological and interfacial tension measurements show that the polymeric surfactant adsorbed at the globule interface does not migrate to the droplet interfaces through the oil phase. This explains, at least partly, the stability improvement of multiple emulsions as polymeric surfactants are used instead of small-molecule surfactants.     

FORMATION AND APPLICATIONS OF MULTIPLE EMULSIONS

Multiple emulsions, especially water-in-oil-in-water (W/O/W) type systems, have potential applications for the formulation and processing of foods, drugs, cosmetics, etc, as each dispersed globule in this type of emulsions consists of liquid compartments separated from the same liquid suspending medium by a thin layer of another immiscible liquid components. This article reviews a series of fundamental works on the formation and dispersion state of multiple emulsion systems and integrates advances made in the area of colloid science so as to obtain further insights into the formulation of W/O/W emulsions. The contents are divided into three sections: methods for preparing multiple emulsions in view of the phase diagram of mixed components, dynamic aspects of oil layer in W/O/W emulsions, and stability of this type of emulsions.     

Double Emulsions Stabilized by Xanthan in the Absence of Hydrophilic Surfactant

The preparation of double water-in-oil-in-water (W/O/W) emulsions containing xanthan gum (XG) in the absence of hydrophilic surfactant was investigated. The emulsions were prepared by the two-step emulsification process. The stability of these systems was evaluated through the evaluation of physicochemical and rheological properties. Microscopic observations in combination with particle size analysis were also performed. The obtained results show that it is possible to prepare stable double emulsions with a single polysaccharide by using the indirect process. The stability depends on the viscosity of the continuous phase and hence the concentration of XG. The apparent viscosity of the emulsions increased with the increase of XG concentration. Particle size analysis shows that the droplet sizes are directly related to XG concentration.     

Rheology of double emulsions

New equations for the viscosity of concentrated double emulsions of core-shell droplets are developed using a differential scheme. The equations developed in the paper predict the relative viscosity (eta(r)) of double emulsions to be a function of five variables: a/b (ratio of core drop radius to shell outer radius), lambda(21) (ratio of shell liquid viscosity to external continuous phase viscosity), lambda(32) (ratio of core liquid viscosity to shell liquid viscosity), phi(DE) (volume fraction of core-shell droplets in double emulsion), and phi(m)(DE) (the maximum packing volume fraction of un-deformed core-shell droplets in double emulsion). Two sets of experimental data are obtained on the rheology of O/W/O (oil-in-water-in-oil) double emulsions. The data are compared with the predictions of the proposed equations. The proposed equations describe the experimental viscosity data of double emulsions reasonably well.