Correlative analysis between morphology and mechanical properties of poly-3-hydroxybutyrate (PHB) blended with polycarprolactone (PCL) using solid-state NMR

Blends of poly(3-hydroxybutyrate) (PHB) and poly(caprolactone) (PCL) were evaluated using multiscale instrumental analyses to reveal the effects of blend ratio and crosslinking reagent. In the multiscale instrumental analyses, molecular mobility from molecular to nano scales was examined by solid-state NMR, while the morphology at the micron scale was revealed by scanning electron microscopy (SEM). PHB-rich blends adopted a sea-island morphology and showed a larger maximum stress due to dispersed PHB filler. A PCL-rich blend also adopted a sea-island morphology but the sea domain consisted of PCL and showed a larger strain at break. An equal ratio PHB/PCL blend had a bicontinuous morphology which showed lower maximum stress and lower strain at break because of large hemispherical defects. The crosslinking reagent changes these heterogeneous morphologies of PHB/PCL blends to homogeneous at the micron scale, which improved tensile properties. Even though the molecular mobility changed with the polymer content and the crosslinking reagent, the bicontinuous and homogeneous morphologies more significantly affected the tensile properties of the PHB/PCL blends.     

Morphology and oxygen sensor response of luminescent Ir-labeled poly(dimethylsiloxane)/polystyrene polymer blend films

Polymer films consisting of a linear poly(dimethylsiloxane) end-functionalized with a luminescent Ir(III) complex (Ir-PDMS), blended with polystyrene (PS), function as optical oxygen sensors. The sensor response arises by quenching of the luminescence from the Ir(III) chromophore by oxygen that permeates into the polymer film. The morphology and luminescence oxygen sensor properties of blend films consisting of Ir-PDMS and PS have been characterized by fluorescence microscopy, atomic force microscopy, and scanning electron microscopy. The investigations demonstrate that microscale phase segregation occurs in the films. In blends that contain a relatively small amount of Ir-PDMS in PS (ca. 10 wt %), the Ir-PDMS exists as circular domains, with diameters ranging from 2 to 5 mum, surrounded by the majority PS phase. For larger weight fractions of Ir-PDMS in the blends, the film morphology becomes bicontinuous. A novel epifluorescence microscopy method is applied that allows the construction of Stern-Volmer quenching images that quantify the oxygen sensor response of the blend films with micrometer spatial resolution. These images provide a map of the oxygen permeability of the polymer blend films with a spatial resolution of ca. 1 mum. The results of this investigation show that the micrometer-sized Ir-PMDS domains display a 2-3-fold higher oxygen sensor response compared to the surrounding PS matrix. This result is consistent with the fact that PDMS is considerably more gas permeable compared to PS. The relationship of the microscale morphology of the blends to their performance as macroscale optical oxygen sensors is discussed.     

Poly(ethylene-co-vinyl alcohol) and poly(methyl methacrylate) blends: Phase behavior and morphology

In this work blends of poly(ethylene-co-vinyl alcohol) (EVOH) with different ethylene contents (27, 32, 38 and 44 mol%) and poly(methyl methacrylate) (PMMA) were prepared by mechanical mixing in the melted state. The miscibility and melting behavior as a function of blend composition and the ethylene content in EVOH copolymers were investigated by means of differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA). The morphology of the cryofractured surfaces was examined by scanning electron microscopy (SEM). DSC and DMTA data show that EVOH/PMMA blends are immiscible, independent of EVOH and blend composition. The SEM analysis in agreement with DMTA analysis indicates that the morphology of phases depends on the blend composition, with phase inversion occurring as the concentration of one or other polymer component increases. However, the copolymer composition apparently does not affect the domain size distribution for blends containing 20 wt% of EVOH or 20 wt% of PMMA. A better phase adhesion is observed mainly for blends with 50 wt% of each polymer component.     

An intimate polycarbonate/poly(methyl methacrylate)/poly(vinyl acetate) ternary blend via coalescence from their common inclusion compound with γ‐cyclodextrin

In this study, we successfully report an intimate ternary blend system of polycarbonate (PC)/poly(methyl methacrylate) (PMMA)/poly(vinyl acetate) (PVAc) obtained by the simultaneous coalescence of the three guest polymers from their common γ‐cyclodextrin (γ‐CD) inclusion compound (IC). The thermal transitions and the homogeneity of the coalesced ternary blend were studied by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The observation of a single, common glass transition strongly suggests the presence of a homogeneous amorphous phase in the coalesced ternary polymer blend. This was further substantiated by solid‐state ¹³C NMR observation of the T_1ρ(¹H)s for each of the blend components. For comparison, ternary blends of PC/PMMA/PVAc were also prepared by traditional coprecipitation and solution casting methods. TGA data showed a thermal stability for the coalesced ternary blend that was improved over the coprecipitated blend, which was phase‐segregated. The presence of possible interactions between the three polymer components was investigated by infrared spectroscopy (FTIR). The analysis indicates that the ternary blend of these polymers achieved by coalescence from their common γ‐CD–IC results in a homogeneous polymer blend, possibly with improved properties, whereas coprecipitation and solution cast methods produced phase separated polymer blends. It was also found that control of the component polymer molar ratios plays a key role in the miscibility of their coalesced ternary blends. Coalescence of two or more normally immiscible polymers from their common CD–ICs appears to be a general method for obtaining well‐mixed, intimate blends. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4182–4194, 2004     

PPEKK/PEI共混物的相容性及拉伸性能

作为相容体系 ,聚芳醚酮与聚醚酰亚胺 (ＰＥＩ)共混物体系的研究受到了研究者的重视[1～ 4] .由于现在已商品化的聚芳醚酮基本上都是半结晶型聚合物 ,所以有有关无定型聚芳醚酮与聚醚酰亚胺共混物的研究鲜见报道 .含二氮杂萘酮结构聚芳醚酮酮 (ＰＰＥＫＫ)是一种新型耐高温聚合物 ,相比于已经商品化的各种聚芳醚酮 ,ＰＰＥＫＫ除具有优异的综合性能外 ,它最大的特点表现在以下两方面 ,ＰＰＥＫＫ耐热性突出 ,玻璃化转变温度 (Ｔｇ)为 2 4 5℃左右 ,远高于各种商品化的聚芳醚酮 ;ＰＰＥＫＫ为无定型聚合物 ,易溶于多种有机极性溶剂 ,大大的扩…     

Compatibility Study of Blends of Acrylic Rubber (ACM), Poly(ethyleneterephalate) (PET), and Liquid Crystalline Polymer (LCP)

The ternary blends of acrylate rubber (ACM), poly(ethyleneterephalate) (PET), and liquid crystalline polymer (LCP) were prepared by varying the amount of LCP, but fixing the ratio of ACM and PET using melt mixing procedure. The compatibility behavior of these blends was investigated with infrared spectroscopy (IR), differential scanning calorimetry (DSC), and dynamic mechanical analyzer (DMA). The IR results revealed the significant interaction between the blend components. Glass transition temperature (T_g) and melting temperature (T_m) of the blends were affected depending on the LCP weight percent in the ACM/PET, respectively. This further suggests the strong interfacial interactions between the blend components. In the presence of ACM, the nucleating effect of LCP was more pronounced for the PET. The thermogravimetric (TGA) study shows the improved thermal stability of the blends.     

PH effects in the complex formation and blending of poly(acrylic acid) with poly(ethylene oxide)

The effect of pH on the complex formation between poly(acrylic acid) (PAA) and poly(ethylene oxide) (PEO) has been studied in aqueous solutions by turbidimetric and fluorescent methods. It was shown that the formation of insoluble interpolymer complexes is observed below a certain critical pH of complexation (pH(crit1)). The formation of hydrophilic interpolymer associates is possible above pH(crit1) and below a certain pH(crit2). The effects of polymer concentrations in solution and PEO molecular weight as well as inorganic salt addition on these critical pH values were studied. The polymeric films based on blends of PAA and PEO were prepared by casting from aqueous solutions with different pHs. These films were characterized by light transmittance measurements and differential scanning calorimetry. The existence of the pH value above which the polymers form an immiscible blend was demonstrated. The transitions between the interpolymer complex, miscible blend, and immiscible blend caused by pH changes are discussed. The recommendations for preparation of homogeneous miscible films based on compositions of poly(carboxylic acids) and various nonionic water-soluble polymers are presented.     

Fourier-transform infrared studies of polymer blends. III. Poly(β-propiolactone)-poly(vinyl chloride) system

Fourier-transform infrared (FTIR) studies of the poly(β-propiolactone) (PPL)-poly(vinyl chloride) (PVC) blend system are presented. PPL-PVC blends are observed to be incompatible in the molten (80°C) and solid (25°C) states, over the entire range of compositions. This is in marked contrast to our previous results of the poly(?-caprolactone)-PVC blend system which was shown to be compatible in the amorphous state. The results of both studies are compared and discussed with particular reference to the detection of intermolecular interactions by FTIR and correlation with compatibility in polyester-PVC blends. The role of the chemical interactions in the compatibilization of polymer blends is discussed in terms of thermodynamic considerations. Finally, it is well known that changes in refractive index of polymer blend compositions can cause frequency shifts of infrared bands, which are particularly relevant to the interpretation of residual peaks obtained by difference spectroscopy. The FTIR results of the PPL-PVC blends are germane to this subject and are discussed.     

Abiotic degradation of poly(dl-lactide), poly(ɛ-caprolactone) and their blends

An effective hydrolytic degradation of PDLLA, PCL and their blends in a phosphate-buffered solution of pH 4.0 at 37 °C for 18 weeks was achieved, observing a considerably faster degradation of PDLLA as compared to PCL due to the hydrophobic and semicrystalline nature of PCL matrix, able to partially prevent water diffusion into the bulk specimen.DSC and FTIR results indicated that PCL phase, in compositions rich in PCL, was very stable against hydrolysis, but the presence of PDLLA in the PDLLA/PCL blends seemed to catalyze the hydrolytic degradation of the PCL phase, probably associated to easier diffusion of water into the PCL domains by the presence of PDLLA amorphous regions. This last trend was proportional to the content of PDLLA in the blends, excepting for the composition 64%PDLLA/36%PCL. It was confirmed that PCL molecules partially delayed hydrolysis of PDLLA molecules, according to FTIR analysis, and the water diffusion prevention level was proportional to the content of PCL in the blends, except for the system 64%PDLLA/36%PCL, which presented a lower extent of degradation than neat PDLLA but higher than the blend 80%PDLLA/20%PCL. This indicated that PCL molecules did not significantly impede hydrolysis of PDLLA molecules in this blend, possibly due to the achievement of a particular structure of the PDLLA/PCL interphase in this blend. In general, hydrolysis of PDLLA/PCL blends was found to be a complex phenomenon depending not only on the content of both polymer phases, but also on the polymer phase crystallinity and morphology.     

The morphology of poly(vinylidene fluoride) crystallized from blends of poly(vinylidene fluoride) and poly(ethyl acrylate)

A combined optical and electron microscopical study has been carried out of the crystallization habits of poly(vinylidene fluoride) (PVF₂) when it is crystallized from blends with noncrystallizable poly(ethyl acrylate) (PEA). The PVF₂/PEA weight ratios were 0.5/99.5,5/95, and 15/85. Isothermal crystallization upon cooling the blends from the single-phase liquid region was carried out in the range 135–155°C, in which the polymer crystallizes in the α-orthorhombic unit cell form. The 0.5/99.5 blend yielded multilayered and planar lamellar crystals. The lamellae formed at low undercoolings were lozenge shaped and bounded laterally by {110} faces. This habit is prototypical of the dendritic lateral habits exhibited by the crystals grown from the same blend at high undercoolings as well as by the constituent lamellae in the incipient spherulitic aggregates and banded spherulites that formed from the 5/95 and the 15/85 blends, respectively. In contrast with the planar crystals grown from the 0.5/99.5 blend, the formation of the aggregates grown from the 5/95 blend is governed by a conformationally complex motif of dendritic lamellar growth and proliferation. The development of these aggregates is characterized by the twisting of the orientation of lamellae about their preferential b-axis direction of growth, coupled with a fan-like splaying or spreading of lamellae about that axis. The radial growth in the banded spherulites formed from the 15/85 blend is governed by a radially periodic repetition of a similar lamellar twisting/fan-like spreading growth motif whose recurrence corresponds to the extinction band spacing. This motif differs in its fan-like splaying component from banding due to just a helicoidal twisting of lamellae about the radial direction. © 1993 John Wiley & Sons, Inc.     

Effect of inert diluent segment on the miscibility behavior of poly(vinylphenol) with poly(acetoxystyrene) blends

Polymer blends of poly(vinylphenol) (PVPh) and poly(styrene‐co‐vinylphenol) with poly(p‐acetoxystyrene) (PAS) were prepared by solution casting from tetrahydrofuran solution. The thermal properties and hydrogen bonding of the blends were investigated by differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy. Although hydrogen bonding existed between the PVPh and PAS segments, the experimental results indicated that PVPh is immiscible with PAS as shown by the existence of two glass‐transition temperatures over the entire composition range by DSC. This phenomenon is attributed to the strong self‐association of PVPh, intramolecular screening, and functional group accessibility effects of the PVPh/PAS blend system. However, the incorporation of an inert diluent moiety such as styrene into the PVPh chain renders the modified polymer to be miscible with PAS. Copolymers containing between 16 and 51 mol % vinylphenol were fully miscible with PAS according to DSC studies. These observed results were caused by the reduction of the strong self‐association of PVPh and the increase of the interassociation between PVPh and PAS segments with the incorporation of styrene on the PVPh chain. According to the Painter‐Coleman association model, the interassociation equilibrium constant of PVPh/PAS blends was determined by a model compound and polymer blend. Good correlation between these two methods was obtained after considering the intramolecular screening and functional group accessibility effect in the polymer blend. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1661–1672, 2002     

Thermal,mechanical and electroactive shape memory properties of polyurethane (PU)/poly (lactic acid) (PLA)/CNT nanocomposites

Polymer blend nanocomposites based on thermoplastic polyurethane (PU) elastomer, polylactide (PLA) and surface modified carbon nanotubes were prepared via simple melt mixing process and investigated for its mechanical, dynamic mechanical and electroactive shape memory properties. Chemical and structural characterization of the polymer blend nanocomposites were investigated by Fourier Transform infrared (FT-IR) and wide angle X-ray diffraction (WAXD). Loading of the surface modified carbon nanotube in the PU/PLA polymer blends resulted in the significant improvement on the mechanical properties such as tensile strength, when compared to the pure and pristine CNT loaded polymer blends. Dynamic mechanical analysis showed that the glass transition temperature (T_g) of the PU/PLA blend slightly increases on loading of pristine CNT and this effect is more pronounced on loading surface modified CNTs. Thermal and electrical properties of the polymer blend composites increases significantly on loading pristine or surface modified CNTs. Finally, shape memory studies of the PU/PLA/modified CNT composites exhibit a remarkable recoverability of its shape at lower applied dc voltages, when compared to pure or pristine CNT loaded system.     

Phase behavior of polymer/diluent/diluent mixtures and their application to control microporous membrane structure

Rechargeable battery separators containing controlled pores were fabricated via the thermally-induced phase separation (TIPS) process. Based on the idea that pores could be manipulated by controlling the liquid–liquid phase separation temperature in the TIPS process, phase boundaries of the polymer–diluent systems were controlled by using diluent mixtures. Phase behaviors of the polymer/diluent/diluent ternary blends consisting of polyethylene (PE) as polymer, and soybean oil (SBO) and dioctyl phthalate (DOP) as diluents were explored. PE/SBO and PE/DOP binary blends, and PE/SOB/DOP ternary blends exhibited typical upper critical solution temperature (UCST) type phase behaviors, and the phase separation temperatures of the PE/SBO blends were higher than those of the PE/DOP blends. When the mixing ratio of the polymer and diluent-mixture was fixed, the phase separation temperature of the PE/SBO/DOP blend initially increased with increasing SBO content in the diluent-mixture passing through a maximum centered at about 80 wt% SBO and decreased beyond this point. Furthermore, the phase separation temperature of the PE/diluent-mixture blend was always higher than that of the PE/SBO blend when the diluent-mixture contained more than or equal to 50 wt% SBO. To understand the observed phase behavior of the blends, thermodynamic analyses based on the lattice-fluid theory were performed. Larger pore membranes were fabricated from the blend when higher phase separation temperatures of the blend were exhibited.     

A novel method for the pore size control of the battery separator using the phase instability of the ternary mixtures

The battery separator plays a key role in determining the capacity of the battery. Since separator performance mainly depends on the pore size of membrane, development of a technique for the fabrication of the membrane having controlled pore size is essential in producing a highly functional battery separator. In this study, microporous membranes having the desired pore size were produced via thermally‐induced phase separation (TIPS) process. Control of the phase boundaries of polymer‐diluent blends is the main concern in manipulating pore size in TIPS process, because pore size mainly depends on the temperature gap between phase separation temperature of the blend and the crystallization temperature of polymer. Microporous membranes having controlled pore size were produced from polyethylene (PE)/dioctyl phthalate (DOP) blends, PE/isoparaffin blends, and polymer/diluent‐mixture ternary blends, that is, PE/(DOP/isoparaffin) blends. PE/DOP binary blends and PE/(DOP/isoparaffin) ternary blends exhibited typical upper critical solution temperature (UCST) type phase behavior, while PE formed a homogeneous mixture with isoparaffin above the crystallization temperature of PE. When the mixing ratio of polymer and diluent‐mixture was fixed, the phase separation temperature of PE/diluent‐mixture blend first increased with increasing DOP content in the diluent‐mixture, went through a maximum centered at about 80 wt % DOP and then decreased. Furthermore, the phase separation temperatures of the PE/diluent‐mixture blends were always higher than that of the PE/DOP blend when diluent‐mixture contained more than or equal to 20 wt % of DOP. Average pore size of microporous membrane prepared from PE/DOP blend and that prepared from PE/isoparaffin blend were 0.17 and 0.07 μm, respectively. However, average pore size of microporous membrane prepared from ternary blends was varied from 0.07 to 0.5 μm by controlling diluent mixing ratio. To understand the phase behavior of ternary blend, phase instability of the ternary mixture was also explored. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2025–2034, 2006     

Morphology of ultrathin polymer films based on poly(ethylene oxide) blends

The structure of ultrathin (15–200 nm) films of two types prepared from polymer blends based on PEO (the crystallizable component), namely, PEO-poly(arylene sulfone oxide) (the amorphous component) and PEO-PB (the amorphous component), has been studied by atomic force microscopy. The content of PEO in both blends is 76 wt %. Ultrathin blend films have been applied on a Si substrate via substrate dipping into dilute solutions of polymer blends in chloroform at room temperature. The rate of the substrate lift has been varied from 0.1 to 1 mm/min. The amorphous-amorphous separation takes place during formation of ultrathin films of the above blends in the course of the substrate lift at the stage of gelation. The crystallization of PEO and dewetting in the resulting two-phase blend gels depend on the rate of the substrate lift and the rigidity of macromolecules of the amorphous component. Moreover, the predominant interaction of the substrate with one of the components plays a significant role in structure formation of ultrathin films of both polymer blends.     

Morphology control of sulfonated poly(ether ketone ketone) poly(ether imide) blends and their use in proton-exchange membranes

Polymer blends based on sulfonated poly(ether ketone ketone) (SPEKK) as the proton-conducting component and poly(ether imide) (PEI) as the second component were considered for proton-exchange membranes (PEMs). The PEI was added to improve the mechanical stability and lower the water swelling in the fuel cell environment. Membranes were cast from solution using N-methyl-2-pyrrolidone (NMP) and dimethylacetamide (DMAc). The ternary, polymer/polymer/solvent, phase diagram was determined to provide guidance on how to control the morphology during solvent casting of blend membranes.

For blends of SPEKK (ion-exchange capacity = 2 mequiv/g) with PEI as the minority component, the morphology consisted of dispersed particles of 0.5–6 μm. Larger particles were achieved by increasing the PEI content and/or lowering the casting temperature. High-temperature annealing after solution casting did not affect the morphology of blend membranes, due to the low mobility and compatibility of the two polymers.

The possible use of SPEKK/PEI blends in PEMs is discussed in terms of existing theories of ion transport in polymers.     

Development of novel elastomeric blends derived from chlorinated nitrile rubber and chlorinated ethylene propylene diene rubber

Chlorinated nitrile rubber (Cl-NBR) has been blended with chlorinated ethylene propylene diene rubber (Cl-EPDM) in different ratios by a conventional mill mixing method. The effect of the blend ratio on processing characteristics, mechanical properties (such as tensile and tear strength, elongation at break, hardness, abrasion resistance, heat build-up and resilience), structure, morphology, glass transition temperature (Tg), thermal stability, flame retardancy, oil resistance, AC conductivity, dielectric properties and transport behavior of petrol, diesel and kerosene were investigated. The shift in absorption bands of blends studied from FTIR spectra, single Tg from DSC analysis and decrease in amorphous nature from XRD showed the molecular miscibility in Cl-NBR/Cl-EPDM blends. SEM images showed the uniform mixing of both Cl-NBR and Cl-EPDM in a 50/50 blend ratio. The TGA curves indicated the better thermal stability of the polymer blend. The elongation at break, heat build-up, resilience and hardness of the polymer blend decreases with an increase in Cl-NBR content in the blend whereas the flame and oil resistance were increased with increase in Cl-NBR content. Among the polymer blends, the maximum torque, tensile strength, tear and abrasion resistance was obtained for the 50/50 blend ratio because of the effective interfacial interactions between the blend components. AC conductivity and dielectric properties of polymer blend increased with increase in the ratio of Cl-NBR in the blend. Different transport properties such as diffusion, permeation and sorption coefficient were measured with respect to nature of solvent and different blend ratios. Temperature dependence of diffusion was used to estimate the activation parameters and the mechanism of transport found to be anomalous.     

Characterisation of Hyaluronic Acid Blends Modified by Poly(N-Vinylpyrrolidone)

The viscosity behaviour and physical properties of blends containing hyaluronic acid (HA) and poly(N-vinylpyrrolidone) (PVP) were studied by the viscometric technique, steady shear tests, tensile tests and infrared spectroscopy. Viscometric and rheological measurements were carried out using blends of HA/PVP with different HA weight fractions (0, 0.2, 0.5, 0.8 and 1). The polymer films and HA/PVP blend films were prepared using the solution casting method. The study of HA blends by viscometry showed that HA/PVP was miscible with the exception of the blend with high HA content. HA and its blends showed a shear-thinning flow behaviour. The non-Newtonian indices (n) of HA/PVP blends were calculated by the Ostwald–de Waele equation, indicating a shear-thinning effect in which pseudoplasticity increased with increasing HA contents. Mechanical properties, such as tensile strength and elongation at the break, were higher for HA/PVP films with w_HA = 0.5 compared to those with higher HA contents. The elongation at the break of HA/PVP blend films displayed a pronounced increase compared to HA films. Moreover, infrared analysis confirmed the existence of interactions between HA and PVP. The blending of HA with PVP generated films with elasticity and better properties than homopolymer films.     

聚己内酯在聚己内酯/聚乙烯基甲基醚共混体系中的结晶研究

通过示差扫描量热(DSC)、广角X射线衍射(WAXD)、小角X射线散射(SAXS)研究了聚己内酯(PCL)/聚乙烯基甲基醚(PVME)共混体系中PCL的结晶行为.研究结果表明,共混聚合物中PCL的结晶度几乎不随体系的组成而发生变化.共混物中PVME的存在没有改变PCL的晶体结构,但是随着PVME含量的增加,片晶之间的距离则大,这主要是由于非晶层增厚引起的.     

聚苯乙烯/顺丁橡胶共混过程中的相结构

利用激光背散射装置结合密炼机对聚合物共混过程进行了在线分析．以典型完全不相容体系聚苯乙烯／顺丁橡胶为共混体系，对不同共混速度下结构参数随共混时间及共混条件如剪切速率等的变化进行了详细讨论．利用扫描电镜与激光背散射在线分析对聚合物共混过程结构参数变化进行了比较，结果显示聚苯乙烯／顺丁橡胶共混物处于熔融态与处于固态时结构基本相同．