双酚A在环氧树脂和端羧丁腈增韧的环氧树脂中作用的研究

本文分别以六氢吡啶、三乙醇胺、70~#酸酐和三氟化硼单乙胺络合物为固化剂,研究了用双酚A改性的环氧树脂和端羧丁腈(简称CTBN)增韧的环氧树脂体系的热、机械性能、微观形貌和交联密度。研究结果表明只有在碱性催化型固化剂六氢吡啶或三乙醇胺下,双酚A的加入才会有突出的增韧效果。结果指出固化物冲击韧性的提高与网络交联密度有关,断裂韧性的提高是析出橡胶相体积分数增大和基体交联密度减小的协同作用所致。     

Influence of carboxyl‐terminated (butadiene‐co‐acrylonitrile) loading on the mechanical and thermal properties of cured epoxy blends

A mixture of epoxy with liquid nitrile rubber, carboxyl‐terminated (butadiene‐co‐acrylonitrile) (CTBN) was cured under various temperatures. The cured resin was a two‐phase system, where spherical rubber domains were dispersed in the matrix of epoxy. The morphology development during cure was investigated by scanning electron microscope (SEM). There was slight reduction in the glass transition temperature of the epoxy matrix (T_g) on the addition of CTBN. It was observed that, for a particular CTBN content, T_g was found to be unaffected by the cure temperature. Bimodal distribution of particles was noted by SEM analysis. The increase in the size of rubber domains with CTBN content is due probably to the coalescence of the rubber particles. The mechanical properties of the cured resin were thoroughly investigated. Although there was a slight reduction in tensile strength and young's modulus, appreciable improvements in impact strength, fracture energy, and fracture toughness were observed. Addition of nitrile rubber above 20 parts per hundred parts of resin (phr) made the epoxy network more flexible. The volume fraction of dispersed rubbery phase and interfacial area were increased with the addition of more CTBN. A two‐phase morphology was further established by dynamic mechanical analysis (DMA). © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2531–2544, 2004     

Thermomechanical properties of liquid‐crystalline epoxy networks arranged by a magnetic field

During the curing process of a liquid‐crystalline epoxy resin, a relatively strong magnetic field was applied, and the thermomechanical properties of the cured resin were investigated. The network orientation and mechanical properties of the cured system were evaluated with wide‐angle X‐ray diffraction, dynamic mechanical analysis, and fracture toughness testing. The cured system was found to have an anisotropic network structure, which arranged along the applied field, and the anisotropy was reflected in the thermomechanical properties. In particular, the fracture toughness of the system dramatically increased when the network chains were arranged across the direction of the crack propagation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 758–765, 2004     

Fracture mechanism of liquid‐crystalline epoxy resin systems with different phase structures

A liquid‐crystalline epoxy resin was cured at two different temperatures. The phases of the cured systems clearly showed isotropic and nematic polydomain structures, which depended on the curing temperature. The fracture toughness of the systems was measured, and the fracture mechanism was investigated with polarized IR measurements. The nematic polydomain structure system showed considerably higher fracture toughness than the isotropic structure. Moreover, both systems exhibited a reorientation of the network chains near the fracture surface during the fracture process, and the region of the network reorientation in the nematic polydomain structure system was larger than that in the isotropic structure system. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4044–4052, 2004     

Fracture toughening of epoxy matrices with blends of resins of different molecular weights and other modifiers

The microstructure and fracture behavior of epoxy mixtures containing two monomers of different molecular weights were studied. The variation of the fracture toughness by the addition of other modifiers was also investigated. Several amounts of high‐molecular‐weight diglycidyl ether of bisphenol A (DGEBA) oligomer were added to a nearly pure DGEBA monomer. The mixtures were cured with an aromatic amine, showing phase separation after curing. The curing behavior of the epoxy mixtures was investigated with thermal measurements. A significant enhancement of the fracture toughness was accompanied by slight increases in both the rigidity and strength of the mixtures that corresponded to the content of the high‐molecular‐weight epoxy resin. Dynamic mechanical and atomic force microscopy measurements indicated that the generated two‐phase morphology was a function of the content of the epoxy resin added. The influence of the addition of an oligomer or a thermoplastic on the morphologies and mechanical properties of both epoxy‐containing mixtures was also investigated. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3920–3933, 2004     

Thermal properties and fracture toughness of a liquid‐crystalline epoxy resin cured with an aromatic diamine crosslinker having a mesogenic group

A mesogenic‐type curing agent was synthesized to introduce a mesogenic group not only into epoxy resin backbones but also into the crosslink units. In the mesogenic curing agent system, the domain size became larger, and the network arrangement in each domain existed to a greater extent than that in a system cured with the ordinary diamine curing system according to the evidence from polarized optical micrographs and polarized Fourier transform infrared mapping measurements. Moreover, the fracture toughness of the system was considerably improved. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2486–2494, 2006     

Relationship between fracture toughness and domain size of liquid‐crystalline epoxy resins having polydomain structure

A liquid‐crystalline (LC) epoxy resin was cured at different temperatures and some types of curing systems having different phase structures (isotropic or polydomain, which have a microscopically ordered LC network structure) were obtained. The diameters of each domain in the polydomain system changed from the small to the larger size. The diameters of the LC domains were evaluated using a polarized optical microscope and the polarized microscopy FTIR mapping method. These systems were used to investigate the relationship between the network arrangement and mechanical properties. The fracture toughness of the cured systems was related to the enlargement of the ordered area in the network structures. With the toughness improvement, the meandering cracks were observed at the fracture surfaces. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 156–165, 2009     

Synthesis and characterization of liquid‐crystalline epoxy and its blend with conventional epoxy

Terephthaloyl chloride was reacted with 4‐hydroxy benzoic acid to get terephthaloylbis(4‐oxybenzoic) acid, which was characterized and further reacted with epoxy resin [diglycidyl ether of bisphenol A (DGEBA)] to get a liquid‐crystalline epoxy resin (LCEP). This LCEP was characterized by Fourier transform infrared spectrometry, ¹H and ¹³C NMR spectroscopy, differential scanning calorimetry (DSC), and polarized optical microscopy (POM). LCEP was then blended in various compositions with DGEBA and cured with a room temperature curing hardener. The cured blends were characterized by DSC and dynamic mechanical analysis (DMA) for their thermal and viscoelastic properties. The cured blends exhibited higher storage moduli and lower glass‐transition temperatures (tan δ_max, from DMA) as compared with that of the pure DGEBA network. The formation of a smectic liquid‐crystalline phase was observed by POM during the curing of LCEP and DGEBA/LCEP blends. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3375–3383, 2003     

Fracture toughness and fracture mechanism of liquid‐crystalline epoxy resins with different polydomain structures

Liquid‐crystalline (LC) epoxy resins were cured at different temperatures to obtain polydomain LC phase–cured resins. The cured resins had polydomain structures with a nematic LC phase and their domain diameters differed depending on the curing temperatures. The relationship between the domain diameter and fracture toughness of the diglycidyl ether of terephthalylidene‐bis‐(4‐amino‐3‐methylphenol) (DGETAM)/m‐phenylenediamine (m‐PDA) systems with the nematic phase and the previously reported smectic LC phase structures was investigated. It was clarified that the highly ordered LC structure (smectic phase) in each domain could improve the fracture toughness. In addition, the changes in the network orientation of the DGETAM/m‐PDA systems were evaluated by a mapping of the microscopic infrared dichroism in the fracture process and their toughening mechanism was suggested. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Clay dispersibility and mechanical property of the epoxy/clay nanocomposites prepared by different treatment methods

The bisphenol‐A type epoxy resin was combined with layered clays. Three types of epoxy/clay nanocomposites were prepared by different clay pretreatment methods, that is, the slurry (clay swelling with polar solvent), organo, and solubilization (organoclay swelling with polar solvent) methods. The organo and solubilization systems showed good dispersibility. The basal spacing of the layered clays in the obtained nanocomposites was evaluated by XRD and TEM observations. The basal spacing of the nanoclay in the solubilization system drastically increased. The mechanical properties were improved with the increase in the clay dispersion. A high modulus and fracture toughness were obtained by improvement of the clay dispersion into the matrix. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1753–1761, 2009     

Thermal properties and fracture toughness of epoxy resins cured by phosphonium and pyrazinium salts as latent cationic initiators

In this work, the latent thermal cationic initiators triphenyl benzyl phosphonium hexafluoroantimonate (TBPH) and benzyl‐2‐methylpyrazinium hexafluoroantimonate (BMPH) were newly synthesized and characterized with IR, ¹H NMR, and P NMR spectroscopy. The thermal and mechanical properties of difunctional epoxy [diglycidyl ether of bisphenol A (DGEBA)] resins cured by 1 phr of either TBPH or BMPH were investigated. The DGEBA/TBPH system showed a higher curing temperature and a higher critical stress intensity factor than the epoxy/BMPH system. This could be interpreted in terms of the slow thermal diffusion rate and bulk structure of the four phenyl groups in TBPH. However, the decomposition activation energy derived from the Coats–Redfern method was lower for epoxy/TBPH. This result was probably due to the fact that a broken short‐chain structure was developed by the steric hindrance of TBPH in the difunctional epoxy resin. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2393–2403, 2003     

Poly(ether ether ketone)‐bischromenes: Synthesis,characterization, and influence on thermal,mechanical, and thermo mechanical properties of epoxy resin

Poly(ether ether ketone) s with terminal propargyl groups (PEEK‐PR) were synthesized from hydroxyl terminated PEEK (PEEKTOH) and characterized. The heat‐triggered polymerization of PEEK‐PR to poly bischromenes having PEEK backbone was confirmed by Fourier transform infrared spectroscopy and differential scanning calorimetric studies. PEEK‐PR was blended with a bisphenol based epoxy resin‐diamino diphenylsulphone system in different proportions and cured to form PEEK‐bischromene‐interpenetrated‐epoxy‐amine networks. Tensile strength and elongation of the cured blends increased up to 10‐phr loading of PEEK‐PR and then declined. Tensile moduli of all formulations were comparable. Fracture toughness increased by a maximum of 33%, and the fractured surface morphology showed a ductile fracture. The blends exhibited slightly lower glass transition temperature to that of the neat epoxy‐amine system. A reference sample of epoxy‐amine was processed with the optimum loading of the precursor polymer, PEEKTOH, and compared its properties with the PEEK‐PR incorporated epoxy systems. In this way, it is found that the incorporation of addition curable propargylated PEEK increases the strength characteristics with adequate thermal stability and fracture toughness for high‐performance structural applications.     

EPOXY RESIN TOUGHENED BY THERMOPLASTICS

Two kinds of tough ductile heatresisting thermoplastic, namely bisphenol A polysulfone (PSF) and polyethersulfone (PES) were used to toughen thermoset epoxy resin. A systematic study on the relationship between the molecular weight and the terminal group of the thermoplastic modifier and the fracture toughness of the modified resin was carried out. The morphology of PSF modified epoxy resin was surveyed. With the same kind of PSF the structure of the epoxy resin and the toughening effect of PSF was also investigated. The fractography of PSF, particle modified epoxy was examined in detail with SEM. The contribution of every possible energy absorption process has been discussed. Crack pinning mechanism seems to be the most important toughening mechanism for tough ductile thermoplastic PSF particle modified epoxy system.     

Investigation of fracture mechanism on liquid crystalline epoxy networks arranged by a magnetic field

A liquid crystalline epoxy resin was cured under non‐ and 10T‐magnetic fields, and polydomain and monodomain networks were obtained, respectively. The fracture toughness of these systems was evaluated and it was clarified that the toughness of the magnetic field system showed a higher value. To investigate the toughening mechanism, polarized micro FTIR measurements were carried out. As a result, it was clarified that their mechanisms were quiet different. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1406–1412, 2006     

Synthesis of hydroxyl‐terminated poly(ether ether ketone) with pendent tert‐butyl groups and its use as a toughener for epoxy resins

Hydroxyl‐terminated poly(ether ether ketone) with pendent tert‐butyl groups (PEEKTOH) was synthesized by the nucleophilic substitution reaction of 4,4′‐difluorobenzophenone with tert‐butyl hydroquinone with potassium carbonate as a catalyst and N‐methyl‐2‐pyrrolidone as a solvent. Diglycidyl ether of bisphenol A epoxy resin was toughened with PEEKTOHs having different molecular weights. The melt‐mixed binary blends were homogeneous and showed a single composition‐dependent glass‐transition temperature (T_g). Kelley–Bueche and Gordon–Taylor equations gave good correlation with the experimental T_g. Scanning electron microscopy studies of the cured blends revealed a two‐phase morphology. A sea‐island morphology in which the thermoplastic was dispersed in a continuous matrix of epoxy resin was observed. Phase separation occurred by a nucleation and growth mechanism. The dynamic mechanical spectrum of the blends gave two peaks corresponding to epoxy‐rich and thermoplastic‐rich phases. The T_g of the epoxy‐rich phase was lower than that of the unmodified epoxy resin, indicating the presence of dissolved PEEKTOH in the epoxy matrix. There was an increase in the tensile strength with the addition of PEEKTOH. The fracture toughness increased by 135% with the addition of high‐molecular‐weight PEEKTOH. The improvement in the fracture toughness was dependent on the molecular weight and concentration of the oligomers present in the blend. Fracture mechanisms such as crack path deflection, ductile tearing of the thermoplastic, and local plastic deformation of the matrix occurred in the blends. The thermal stability of the blends was not affected by blending with PEEKTOH. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 541–556, 2006     

有机硅改性环氧树脂的合成与性能研究

用氨基硅油和双酚A型环氧树脂为原料合成一种新型的环氧树脂。研究了不同反应时间、不同反应温度以及不同氨基硅油含量对改性环氧树脂性能的影响,用热重法对改性树脂的耐热性进行了表征。结果表明,用工业产的氨基硅油合成的改性环氧树脂同样具有良好的韧性和耐热性。     

Thermal and mechanical properties of a dendritic hydroxyl‐functional hyperbranched polymer and tetrafunctional epoxy resin blends

Blends of a tetrafunctional epoxy resin, tetraglycidyl‐4,4′‐diaminodiphenylmethane (TGDDM), and a hydroxyl‐functionalized hyperbranched polymer (HBP), aliphatic hyperbranched polyester Boltorn H40, were prepared using 3,3′‐diaminodiphenyl sulfone (DDS) as curing agent. The phase behavior and morphology of the DDS‐cured epoxy/HBP blends with HBP content up to 30 phr were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and scanning electron microscopy (SEM). The phase behavior and morphology of the DDS‐cured epoxy/HBP blends were observed to be dependent on the blend composition. Blends with HBP content from 10 to 30 phr, show a particulate morphology where discrete HBP‐rich particles are dispersed in the continuous cured epoxy‐rich matrix. The cured blends with 15 and 20 phr exhibit a bimodal particle size distribution whereas the cured blend with 30 phr HBP demonstrates a monomodal particle size distribution. Mechanical measurements show that at a concentration range of 0–30 phr addition, the HBP is able to almost double the fracture toughness of the unmodified TGDDM epoxy resin. FTIR displays the formation of hydrogen bonding between the epoxy network and the HBP modifier. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 417–424, 2010     

Influence of the loading rate on liquid‐crystalline epoxy resin systems

The fracture toughness of liquid‐crystalline epoxy systems, which had a nematic polydomain structure (domain size about 40 μm), with an increasing loading rate was evaluated. In this system, the fracture toughness dramatically decreased from 1.96 to 0.22 MN/m^3/2 with an increasing loading rate (0.1–5 mm/min). The network orientation near the fracture surface of different loading rate systems was investigated with polarized optical microscopy and polarized infrared spectroscopy. As a result, a large oriented region of mesogenic groups was observed near the fracture surface in the relatively low loading rate (0.1 and 0.5 mm/min) systems, but such a phenomenon was not observed in the high loading rate (2 and 5 mm/min) systems. These results showed that the high fracture toughness of the system at the low loading rate was due to the magnitude and region of the reorientation of the mesogenic groups in the fracture process and that high toughness could not be achieved at a high loading rate because the loading rate was too fast to allow orientation of the networks containing the mesogenic groups. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1296–1302, 2005     

Interfacial control and mechanical properties of carbon black‐reinforced carboxyl‐terminated butadiene acrylonitrile rubber/epoxy polymer composites

Carbon black (CB) particles were employed as a reinforcing filler in carboxyl‐terminated butadiene acrylonitrile rubber (CTBN)/epoxy resin (diglycidyl ether of bisphenol‐A (DGEBA))/aromatic diamine (diamino diphenyl methane (DDM)) network polymer blends. The strength, modulus, and ability to absorb impact energy of the resulting composites were evaluated. The aim of this work was to determine the effects of interfacial interactions between components, and processing conditions (especially temperature) on mechanical properties. The application of high temperatures during the kneading process resulted in strong interfacial interactions between the CB particles and the CTBN. The formation of strong bonds at the CB/CTBN interfaces during kneading was the key factor in obtaining high strength and high impact energy absorbance. The composites also exhibited good adhesive strength during both shear and peel stress tests.     

Toughening of highly crosslinked epoxy resins by reactive blending with bisphenol A polycarbonate. II. Yield and fracture behavior

The yield and fracture behavior of highly crosslinked epoxy resin modified by a reactive blending process carried out in the presence of bisphenol A polycarbonate has been studied. It was found that the fracture toughness of this blend system increases markedly with increasing PC content in the blend. Scanning electron microscopy of the fractured surfaces indicated a crack blunting mechanism as the main source of energy dissipation in the various investigated blend compositions. No evidence of phase separation of the minor component during the curing and postcuring steps was observed. The yield data were correlated with the fracture toughness data to evaluate the extent of crack-tip blunting. © 1994 John Wiley & Sons, Inc.