钙钛矿型La0.8Sr0.2FeO3中的晶格氧用于甲烷选择氧化取合成气

用自燃烧法制备了钙钛矿型La0.8Sr0.2FeO3催化剂。用H2－TPR考察了催化剂表面的氧消耗过程，用程序升温表面反应（TPSR）研究了甲烷与催化剂表面氧物种的反应，用在线质谱脉冲反应和甲烷／氧切换反应研究了催化剂的晶格氧选择氧化甲烷制合成气。结果表明，催化剂上存在两种氧物种，无气相氧存在时，强氧化性氧物种首先将甲烷氧化为CO2和H2O；而后提供的氧化性较弱的晶格氧具有良好的甲烷部分氧化选择性，可将甲烷氧化为合成气CO和H2（选择性可达95％以上）。在900℃一的CH4／O2切换反应结果表明，甲烷能与La0.8Sr0.2FeO3中的晶格氧反应选择性地生成CO和H2，失去晶格氧的La0.8Sr0.2FeO3能与气相氧反应恢复其晶格氧。在合适的反应条件下，用La0.8Sr0.2FeO3催化剂的晶格氧化替分子氧按Redox模式实现甲烷选择氧化制合成气是可能的。     

钙钛矿型La0.8Sr0.2FeO3中的晶格氧用于甲烷选择氧化制取合成气

 用自燃烧法制备了钙钛矿型La0．8Sr0．2FeO3催化剂．用H2－TPR考察了催化剂表面的氧消耗过程，用程序升温表面反应（TPSR）研究了甲烷与催化剂表面氧物种的反应，用在线质谱脉冲反应和甲烷／氧切换反应研究了催化剂的晶格氧选择氧化甲烷制合成气．结果表明，催化剂上存在两种氧物种，无气相氧存在时，强氧化性氧物种首先将甲烷氧化为CO2和H2O；而后提供的氧化性较弱的晶格氧具有良好的甲烷部分氧化选择性，可将甲烷氧化为合成气CO和H2（选择性可达95％以上）．在900℃下的CH4／O2切换反应结果表明，甲烷能与La0．8Sr0．2FeO3中的晶格氧反应选择性地生成CO和H2，失去晶格氧的La0．8－Sr0．2FeO3能与气相氧反应恢复其晶格氧．在合适的反应条件下，用La0．8Sr0．2FeO3催化剂的晶格氧代替分子氧按Redox模式实现甲烷选择氧化制合成气是可能的．     

Sr取代LaFeO3钙钛矿的结构性质和催化性能（英文）

Sr2+对La3+的部分取代导致LaFeO3的结构性质和催化性能发生了显著变化.钙钛矿结构由LaFeO3的正交型变成了La0.8Sr0.2FeO3的近立方型.由于电荷补偿效应,Sr2+取代La3+导致部分Fe3+氧化为Fe4+,同时产生氧空穴,因而提高了La0.8Sr0.2FeO3的还原性能.由于氧空穴的作用,La0.8Sr0.2FeO3催化剂在CO氧化和CH4燃烧反应中均表现出较LaFeO3高的催化活性.在CO氧化反应中,氧空穴有利于反应物分子的吸附并加速了气相氧分子在表面上的解离;而在CH4燃烧反应中,氧空穴则促进了晶格氧物种从体相到表面的扩散.     

Sr取代LaFeO_3钙钛矿的结构性质和催化性能(英文)

Sr2+对La3+的部分取代导致LaFeO3的结构性质和催化性能发生了显著变化.钙钛矿结构由LaFeO3的正交型变成了La0.8Sr0.2FeO3的近立方型.由于电荷补偿效应,Sr2+取代La3+导致部分Fe3+氧化为Fe4+,同时产生氧空穴,因而提高了La0.8Sr0.2FeO3的还原性能.由于氧空穴的作用,La0.8Sr0.2FeO3催化剂在CO氧化和CH4燃烧反应中均表现出较LaFeO3高的催化活性.在CO氧化反应中,氧空穴有利于反应物分子的吸附并加速了气相氧分子在表面上的解离;而在CH4燃烧反应中,氧空穴则促进了晶格氧物种从体相到表面的扩散.     

用晶格氧为氧源的甲烷部分氧化制合成气

 采用热重分析技术在甲烷气氛下考察了储氧材料Fe2O3提供晶格氧的过程，用甲烷／氧切换反应和在线质谱检测方法研究了以Fe2O3晶格氧代替气相氧用于甲烷部分氧化制合成气的可能性．结果表明，Fe2O3在甲烷气氛下的还原过程包括Fe2O3→Fe3O4和Fe3O4→FeO→Fe，甲烷被氧化为CO2和H2O．在750℃下进行的CH4／O2切换反应结果表明，首先，约25％的CH4与Fe2O3中的晶格氧反应，生成CO2和H2O，然后，生成的CO2和H2O与剩余的约75％的CH4在Ni／Al2O3催化剂上进行蒸汽重整和C\r\nO2重整，从而按燃烧－重整机理实现甲烷部分氧化制合成气．选择合适的CH4／O2切换条件，可使甲烷高转化率、高选择性地生成合成气．     

纳米La0.8A’0.2Mn1-xCuxO3（A’=Ce and/or Sr）的制备、表征及其高效催化NO+CO的性能研究

采用柠檬酸-溶胶凝胶法制得钙钛矿型复合氧化物La0.8Ce0.2Mn1-xCuxO3(x=0.2,0.3,0.4),La0.8Sr0.2Mn0.6Cu0.4O3,La0.8Ce0.1Sr0.1Mn0.6 Cu0.4 O3,并采用X射线衍射(XRD)、扫描电镜(SEM)、比表面积(BET)、X射线光电子能谱(XPS)对其进行表征,测试了复合氧化物对CO+NO的催化活性。结果表明:La0.8Ce0.1Sr0.1Mn0.6Cu0.4O3催化活性最好,150℃时CO转化率91.8%,300℃时NO转化率100%;对于La0.8Ce0.2Mn1-xCuxO3(x=0.2,0.3,0.4),比表面积和颗粒的大小及分散度是影响催化活性的主要因素;对于La0.8Ce0.2Mn0.6Cu0.4O3,La0.8 Sr0.2 Mn0.6 Cu0.4 O3,La0.8 Ce0.1 Sr0.1 Mn0.6 Cu0.4 O3,催化剂的组成是影响催化活性的关键因素。     

Comparison of LaFeO3, La0.8Sr0.2FeO3, and La0.8Sr0.2Fe0.9Co0.1O3 perovskite oxides as oxygen carrier for partial oxidation of methane

Comparison of LaFeO3, La0.8Sr0.2FeO3, and La0.8Sr0.2Fe0.9CO0.1O3 perovskite oxides as oxygen carrier for partial oxidation of methane in the absence of gaseous oxygen was investigated by continuous flow reaction and sequential redox reaction, Methane was oxidized to syngas with high selectivity by oxygen species of perovskite oxides in the absence of gaseous oxygen. The sequential redox reaction revealed that the structural stability and continuous oxygen supply in redox reaction decreased over La0.8Sr0.2Fe0.9Co0. 1O3 oxide, while LaFeO3 and La0.8Sr0.2FeO3 exhibited excellent structural stability and continuous oxygen supply.     

低温熔盐法制备球状多孔 La1-xSrxMn0.8Fe0.2O3（0≤x≤0.6）及其催化 CO氧化性能

汽车尾气中 CO, HC, NOx,硫化物及其颗粒粉尘严重危害人们身体健康和大气环境,是大气环境的主要污染源之一.目前,尾气净化是其减排的最主要方式.汽车尾气催化剂的发展经历了几代的研究,一直以来广泛采用 Pt, Pd和 Rh等贵金属,但因其资源匮乏,价格昂贵,容易被 S和 P中毒,因此人们逐渐将目光投向非贵金属催化剂的研发.钙钛矿复合氧化物因具有独特的物理化学性质以及灵活的“化学剪裁”特性而在材料研究等领域颇受青睐,有望成为贵金属催化剂的替代品.一般而言,催化剂的比表面积越大,表面活性位点越多,其催化活性越高,且会明显降低起燃温度.目前,一些制备工艺,如水热法、共沉淀法、微乳液法和硬模板法,虽可在一定程度上提高催化剂的比表面积,但却存在费时、耗能及制备工艺复杂等缺点.因此,如何简单有效地制备出大比表面积的钙钛矿型催化剂依然是一个难题.本文以合成的分级多孔δ-MnO2微球为模板,采用熔盐法制备出球状多孔 La1-xSrxMn0.8Fe0.2O3(0≤x≤0.6)钙钛矿氧化物,研究了球状多孔钙钛矿氧化物的形成过程和合适的制备温度,以及 B位 Fe3+掺杂量为20%时 A位 Sr2+掺杂量对钙钛矿催化剂结构和催化活性的影响.采用 X射线粉末衍射、扫描电子显微镜、透射电子显微镜、N2吸附-脱附、傅里叶红外光谱(FT-IR)和 X射线能谱(XPS)等方法对催化剂进行了表征.在固定床石英管反应器上评价了催化剂催化 CO氧化活性及稳定性,采用气相色谱联接氢火焰离子化检测器检测了产物和反应物的组成.结果表明,以分级多孔δ-MnO2微球为模板,采用熔盐法在450oC反应4 h制备出的球状多孔 La1-xSrxMn0.8Fe0.2O3(0≤x≤0.6)钙钛矿氧化物具有良好的结晶性、较大的比表面积(55.73 m2/g)和孔体积(0.37 cm3/g).其球状多孔结构的形成可分为两个阶段：原位形成钙钛矿相和纳片表面析出钙钛矿晶粒及钙钛矿晶粒的再生长.另外, FT-IR光谱表明, Fe3+和 Sr2+成功进入 A, B位.同时, CO转化曲线表明, B位 Fe3+的掺杂量为20%时, A位 Sr2+的掺杂量高于30%时可以明显改善催化剂催化 CO氧化活性： La1-xSrxMn0.8Fe0.2O3(0≤x≤0.3)的T50和T90分别在180和198oC左右;而 La0.55Sr0.45Mn0.8Fe0.2O3和 La0.4Sr0.6Mn0.8Fe0.2O3的T50均低于125oC; La0.55Sr0.45Mn0.8Fe0.2O3的T90为181oC,而 La0.4Sr0.6Mn0.8Fe0.2O3却仍低于125oC. XPS结果则证明,较高的催化活性得益于 La0.4Sr0.6Mn0.8Fe0.2O3表面存在较多的 Mn4+、氧空位及吸附氧.最后, La0.55Sr0.45Mn0.8Fe0.2O3和 La0.4Sr0.6Mn0.8Fe0.2O3的稳定性测试结果表明,采用熔盐法以δ-MnO2为模板在450oC焙烧4 h制备的多孔球状钙钛矿具有较好的催化稳定性.虽然催化剂制备工艺简单,周期短,但比表面积最大只有55.73 m2/g,为硬模板法的1/2,因此提高比表面积将是今后研究的方向.     

还原剂对La0.7Sr0.3Co0.8Fe0.2O3钙钛矿催化剂NOx储存性能的影响

采用溶胶-凝胶法制备了La0.7Sr0.3Co0.8Fe0.2O3钙钛矿催化剂,考察了还原剂种类(CO,C3H6,H2)对催化剂在氮氧化物储存还原(NSR)循环前后的氮氧化物储存量(NSC)和NO-to-NO2转化率的影响.O2程序升温脱附(O2-TPD)实验结果表明,CO还原后的钙钛矿催化剂上形成了较多的氧空位,而氧空位则是一种有效的NOx储存活性中心.活性测试和傅里叶红外变换(FTIR)光谱表征结果显示:在NSR循环中,以CO为还原剂时催化剂显示了最佳的氮氧化物(NOx)储存效果.进一步的研究结果显示,当采用CO作为还原剂时,经过三次NSR循环后,催化剂中出现了Sr3Fe2O7新物相,而该物相可能具有比La0.7Sr0.3Co0.8Fe0.2O3钙钛矿更佳的NOx储存性能.综上所述,CO作为还原剂时可能使钙钛矿催化剂产生更多的氧空位以及更易于储存NOx的Sr3Fe2O7物相,这些原因使其NOx储存性能得到了大幅度改善.     

氧载体的氧物种直接氧化甲烷制合成气

甲烷部分氧化制合成气由于合成气中n(H2)/n(CO)接近2,可直接用于甲醇合成或烃类F-T合成等后续工业过程而在国内外受到了广泛的关注。利用氧载体的氧物种在无气相氧下直接选择氧化甲烷制合成气是天然气化工利用的新方法,本文介绍了该方法的基本原理、概念工艺和对氧载体的性能要求,对应用于该方法的铈基复合氧化物的掺杂和助剂对选择氧化甲烷性能的影响、钙钛矿氧化物氧载体的氧缺陷、氧物种迁移、结构稳定性及其氧物种氧化甲烷的性能进行了阐述和分析,提出了控制氧载体表面状态是获得高合成气选择性的关键,并对该技术今后的研究重点进行了展望。     

Comparison of LaFeO3, La0.8Sr0.2FeO3, and La0.8Sr0.2Fe0.9Co0.1O3 perovskite oxides as oxygen carrier for partial oxidation of methane

Comparison of LaFeO3, La0.8Sr0.2FeO3, and La0.8Sr0.2Fe0.9Co0.1O3 perovskite oxides as oxygen cartier for partial oxidation of methane in the absence of gaseous oxygen was investigated by continuous flow reaction and sequential redox reaction. Methane was oxidized to syngas with high selectivity by oxygen species of perovskite oxides in the absence of gaseous oxygen. The sequential redox reaction revealed that the structural stability and continuous oxygen supply in redox re-action decreased over La0.8Sr0.2Fe0.9Co0.1O3 oxide, while LaFeO3 and Lao.sSro.2FeO3 exhibited excellent structural stability and continuous oxygen supply.     

Partial Oxidation of Methane to Syngas Using Lattice Oxygen of La1-xSrxFeO3

Catalytic partial oxidation of methane to syngas using the lattice oxygen of La1-xSrxFeO3 perovskite oxide catalysts in place of molecular oxygen was studied. La1-xSrxFeO3 (x＝0, 0.1, 0.2,0.5) perovskite oxides were prepared by the "auto-combustion method". XRD analysis showed that all La1-xSrxFeO3 samples have a single-phase perovskite-type oxide. The redox properties of the catalysts were investigated by temperature programmed reduction with hydrogen (H2-TPR). Reducibility of the catalysts increase with the increasing of the Sr2+ content. The oxygen species of the catalysts and their reaction with CH4 were studied by the temperature programmed surface reaction (CH4-TPSR). In the absence of gas phase oxygen, there exist two kinds of oxygen species on the catalysts. One kind of the oxygen species with strong oxidative ability is produced first, which can oxidize CH4 completely to CO2 and H2O.Then, the second oxygen species with weak oxidative ability is formed, which can oxidize CH4 partially to CO and H2 with high selectivity. The number of the oxygen species with strong oxidative ability in the CH4-TPSR tends to become zero at low x values (x≤0.1). Under suitable reaction conditions, switching alternatively the reactions of 11% O2-Ar and 11% CH4-He over a La0.sSr0.2FeO3 catalyst at 900 ℃ allows methane to be selectively converted to synthesis gas (CH4 conversion ～90%, CO selectivity ＞93%) using the lattice oxygen of the perovskite oxide catalyst in a redox mode.     

甲烷部分氧化制合成气的钙钛矿型致密透氧膜反应器的数值模拟(英文)

采用等温理论模型,以甲烷催化氧化制合成气为模型反应,模拟非担载钙钛矿型致密透氧膜反应器的性能。分别研究了Ｌａ_０．２Ｂａ_０．８Ｆｅ_０．８Ｃｏ_０．２Ｏ_(３－δ)、Ｌ３０．２Ｓｒ０．８Ｆｅ０．８Ｃｏ０．２Ｏ３－δ和ＳｒＦｅＣｏ０．５Ｏｘ三种透氧速率不同的膜材料、膜反应器的尺寸以及反应工艺条件对ＣＨ４转化率、ＣＯ选择性和Ｈ２／ＣＯ摩尔比的影响,对膜反应实验具有指导意义。     

THE ROLE OF LATTICE AND GASEOUS OXYGEN ON THE OXIDATIVE COUPLING OF METHANE STUDIED BY A PULSE REACTION TECHNIQUE

A comparative study of the role of lattice and gaseous oxygen in theoxidative coupling of methane over Na~ /Cao and Ca_xSr_(1-x)TiO_3 perovskiteoxide catalysts was performed by using a pulse reaction technique with CH_4,O_2 and mixtures of CH_4and O_2.It was found that there is an oxygen species onthe Surface of Cao which is active only for the total oxidation of methane at thereaction temperature.These oxygen species.once reacted with methane andconsumed,can be regenerated by the adsorption of oxygen molecules from thegas phase or by the migration of the lattice oxysen from the bulk onto thesurface.In contrast,no such oxygen species and no reaction can be detected bymethane pulsed over Ca_xSr_(1-x)TiO_3perovskite oxide catalysts.Na~ can heavilysuppress the non-selective oxygen species on the surface,and When 5mol%Na~ was incorporated onto the surface of Cao,the sample showed no reactivityto methane.When oxygen exists in the gas phase,or the pulse containsmethane and oxygen,the reaction over(Cao is mai     

An X-ray absorption spectroscopic study on mixed conductive La0.6Sr0.4Co0.8Fe0.2O(3-δ) cathodes. I. Electrical conductivity and electronic structure

The electrical conduction mechanism of mixed conductive perovskite oxides, La(0.6)Sr(0.4)Co(0.8)Fe(0.2)O(3-δ), for cathode materials of solid oxide fuel cells has been investigated from electronic structural changes during oxygen vacancy formation. La(0.6)Sr(0.4)Co(0.8)Fe(0.2)O(3-δ) was annealed under various oxygen partial pressures p(O(2))s at 1073 K and quenched. Iodometric titration indicated that the oxygen nonstoichiometry of La(0.6)Sr(0.4)Co(0.8)Fe(0.2)O(3-δ) depended on the annealing p(O(2)), with more oxygen vacancies introduced at lower than at higher p(O(2))s. X-Ray absorption spectroscopic measurements were performed at the O K-, Co L-, Fe L-, Co K-, and Fe K-edges. The valence states of the Co and Fe ions were investigated by the X-ray absorption near edge structure (XANES) at the Co and Fe L(III)-edges. While the Fe average valence was almost constant, the valence of the Co ions decreased with oxygen vacancy introduction. The O K-edge XANES spectra indicated that electrons were injected into the Co 3d/O 2p hybridization state with oxygen vacancy introduction. Both absorption edges at the Co and Fe K-edge XANES shifted towards lower energies with oxygen vacancy introduction. The shift at the Co K-edge resulted from the decrease in the Co average valence and that at the Fe K-edge appeared to be caused by changes in the coordination environment around the Fe ions. The total conductivity of La(0.6)Sr(0.4)Co(0.8)Fe(0.2)O(3-δ) decreased with decreasing p(O(2)), due to a decreasing hole concentration.     

Selective Hydrogen Oxidation in the Presence of C3 Hydrocarbons Using Perovskite Oxygen Reservoirs

Perovskite‐type oxides, ABO₃, can be successfully applied as solid “oxygen reservoirs” in redox reactions such as selective hydrogen combustion. This reaction is part of a novel process for propane oxidative dehydrogenation, wherein the lattice oxygen of the perovskite is used to combust hydrogen selectively from the dehydrogenation mixture at 550 °C. This gives three key advantages: it shifts the dehydrogenation equilibrium to the side of the desired products, heat is generated, thus aiding the endothermic dehydrogenation, and it simplifies product separation (H₂O vs H₂). Furthermore, the process is safer since it uses the catalysts’ lattice oxygen instead of gaseous O₂. We screened fourteen perovskites for activity, selectivity and stability in selective hydrogen combustion. The catalytic properties depend strongly on the composition. Changing the B atom in a series of LaBO₃ perovskites shows that Mn and Co give a higher selectivity than Fe and Cr. Replacing some of the La atoms with Sr or Ca also affects the catalytic properties. Doping with Sr increases the selectivity of the LaFeO₃ perovskite, but yields a catalyst with low selectivity in the case of LaCrO₃. Conversely, doping LaCrO₃ with Ca increases the selectivity. The best results are achieved with Sr‐doped LaMnO₃, with selectivities of up to 93 % and activities of around 150 μmol O m^?2. This catalyst, La_0.9Sr_0.1MnO₃, shows excellent stability, even after 125 redox cycles at 550 °C (70 h on stream). Notably, the activity per unit surface area of the perovskite catalysts is higher than that of doped cerias, the current benchmark of solid oxygen reservoirs.     

高性能Sm0.5Sr0.5CoO3阴极的制备与表征

用固相合成法合成了Sm0.5Sr0.5CoO3 (SSC)中温固体氧化物燃料电池阴极材料.以La0.9Sr0.1Ga0.8Mg0.2O3为电解质,利用多种技术考察了不同温度(1173～1373 K)焙烧的SSC阴极,以及1173 K 焙烧、掺杂La0.8Sr0.2Ga0.8Mg0.15Co0.05O3(LSGMC5)或La0.8Sr0.2Ga0.8Mg0.09Co0.11O3 (LSGMC11)高氧离子电导材料的复合SSC阴极.SEM的结果显示,随着电极焙烧温度的增加,电极的颗粒度增大,孔隙度减小；LSGMC5、LSGMC11的掺杂对电极微观结构影响不大.交流阻抗和极化实验的结果表明,SSC电极的活性随电极焙烧温度的增加而减小,电极的最佳焙烧温度在1173 K左右；掺杂了LSGMC5或LSGMC11的复合SSC电极的活性以及稳定性显著高于SSC电极.     

Unsteady-state direct partial oxidation of methane to synthesis gas in a fixed-bed reactor using AFeO3 (A = La, Nd, Eu) perovskite-type oxides as oxygen storage

Direct partial oxidation of methane to synthesis gas on AFeO(3) (A = La, Nd, Eu) oxides by a novel sequential redox cyclic reaction in the absence of gaseous oxygen was investigated over a fixed-bed reactor. These oxides were prepared by the sol-gel method and characterized by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) techniques. XRD analysis showed that all AFeO(3) (A = La, Nd, Eu) oxides, calcined at 1173 K, are single-phase perovskites. The CH(4)-TPSR/MS and continuous reaction experiments indicated that the AFeO(3) (A = La, Nd, Eu) oxides provide mostly oxygen species, as the sole oxidant originated from lattice oxygen instead of gaseous oxygen, which can oxidize CH(4) to synthesis gas with high selectivity in the absence of gaseous oxygen. In terms of material economics and the amount of oxygen species for synthesis gas formation, the LaFeO(3) sample exhibits the best performance among these tested AFeO(3) oxides for synthesis gas production. The pulse experiments at different temperatures showed that the rate of oxygen migration during the CH(4) reaction with LaFeO(3) is strongly affected by the reaction temperature, and increases with rising temperature, which is favorable to much more CH(4) selective oxidation at high temperature. The two types of oxygen species are identified by experiments of continuous reactions and pulses, and confirmed by XPS. Methane can be converted selectively to synthesis gas by consumption of lattice oxygen, and general carbonaceous deposits on the catalyst surface do not occur under the appropriate reaction conditions by sequential redox cycles. The performance of selective oxidation of CH(4) to synthesis gas can be recovered by reoxidation using gaseous molecular oxygen; the LaFeO(3) oxide maintains relatively high catalytic activity and structural stability in redox atmospheres.     

La-Sr-Fe-Co系钙钛矿型汽车尾气净化催化剂的性能研究

用柠檬酸配合法制备了钙钛矿型复合氧化物La0.8 Sr0.2 Fex Co1-xO3催化剂，研究了Fe和Co的含量对丙烯和氮氧化合物的催化转化的影响，并对其热稳定性进行了考察，用XRD、Mossbauer谱、O2-TPD和IR表征手段将催化剂性能与Fe、Co含量和氧脱附性能进行了关联，研究结果表明：适量的Co和Fe离子的存在，不但能使催化剂结构更接近理想钙钛矿型，而且对催化剂反应性能都起着积极的作用；氧在反应中起着非常关键的作用；催化剂显示了良好的热稳定性。