Enhanced adsorption performance of a novel Fe‐Mn‐Zr metal oxide nanocomposite adsorbent for anionic dyes from binary dye mix: Response surface optimization and neural network modeling

A novel adsorbent, Fe‐Mn‐Zr metal oxide nanocomposite was synthesized and investigated for removal of methyl orange (MO) and eosin yellow (EY) dyes from binary dye solution. The magnetic nanocomposite has shown surface area of 143.01 m²/g and saturation magnetization of 15.29 emu/g. Optimization was carried out via response surface methodology (RSM) for optimizing process variables, and optimum dye removal of 99.26% and 99.55% were obtained for MO and EY dye, respectively with contact time 62 min, adsorbent dose 0.45 g/l, initial MO concentration 11.0 mg/l, and initial EY concentration 25.0 mg/l. A feed forward back propagation neural network model has shown better prediction ability than RSM model for predicting MO and EY dye removal (%). Adsorption process strictly follows Langmuir isotherm model, and enhanced adsorption capacities of 196.07 and 175.43 mg/g were observed for MO and EY dye, respectively due to synergistic effects of physicochemical properties of trimetal oxides. Surface adsorption and pore diffusions are the mechanisms involved in the adsorption as revealed from kinetic studies.     

Mixed phase Fe2O3/Mn3O4 magnetic nanocomposite for enhanced adsorption of methyl orange dye: Neural network modeling and response surface methodology optimization

In this research, a novel magnetic mesoporous adsorbent with mixed phase of Fe₂O₃/Mn₃O₄ nanocomposite was prepared by a facile precipitating method and characterized extensively. The prepared nanocomposite was used as adsorbent for toxic methyl orange (MO) dye removal from aqua matrix considering its high surface area (178.27 m²/g) with high saturation magnetization (23.07 emu/g). Maximum dye adsorption occurs at solution pH 2.0 and the electrostatic attraction between anionic form of MO dye molecules and the positively charged nanocomposite surface is the main driving force behind this adsorption. Response surface methodology (RSM) was used for optimizing the process variables and maximum MO removal of 97.67% is obtained at optimum experimental condition with contact time, adsorbent dose and initial MO dye concentration of 45 min, 0.87 g/l and 116 mg/l, respectively. Artificial neural network (ANN) model with optimum topology of 3–5–1 was developed for predicting the MO removal (%), which has shown higher predictive ability than RSM model. Maximum adsorption capacity of this nanocomposite was found to be 322.58 mg/g from Langmuir isotherm model. Kinetic studies reveal the applicability of second‐order kinetic model with contribution of intra‐particle diffusion in this process.     

Gold Nanoparticles Loaded on Activated Carbon as Novel Adsorbent for Kinetic and Isotherm Studies of Methyl Orange and Sunset Yellow Adsorption

In this research, a novel adsorbent gold nanoparticle loaded on activated carbon (Au-NP-AC) was synthesized by a low cost in a routine protocol. Subsequently, this novel material characterization and identification are followed by different techniques such as th eBruner–Emmet–Teller (BET) theory, scanning electron microcopy, and transmission electron microscopy analysis. Unique properties such as high BET surface area (>1229.55 m²/g) and low pore size (<22.46 Å) and average particle size lower than 48.798 Å in addition to high reactive atom and presence of various functional groups make it possible for efficient removal of sunset yellow (SY) and methyl orange (MO). Generally, the influence of variables including amount of adsorbent, initial dyes concentration, contact time, temperature on dyes removal percentage has great effect on removal percentage that their influence was optimized. The kinetic of proposed adsorption processes efficiently followed, pseudo-second-order and intra-particle diffusion approach. The equilibrium data of the removal strongly follow the Langmuir monolayer adsorption with high adsorption capacity in a short amount of time. This novel adsorbent by small amount (0.01 g) really is applicable for removal of high amount of both dyes (MO and SY) in short time (<18 minutes). Equilibrium data fitted well with the Langmuir model at all amount of adsorbent, while maximum adsorption capacity for MO 161.29 mg g^?1 and for SY 227.27 for 0.005 g of Au-NP-AC.     

Facile synthesis of magnetic hybrid metal–organic frameworks with high adsorption capacity for methylene blue

A magnetic hybrid material (Fe₃O₄‐COOH/HKUST‐1) was easily synthesized via a two‐step simple solvothermal method. Through adding sodium acrylate directly into the synthesis of Fe₃O₄ spheres, the surface has more carboxyl groups. It is notable that the reactions proceed without use of organic surfactants. The magnetic hybrid material was characterized using various techniques. The magnetic hybrid material has a high specific surface area (430.15 m² g⁻¹) and excellent magnetism (23.65 emu g⁻¹). It is an efficient adsorbent for removing organic dyes like methylene blue (MB) from aqueous solution. It also can be easily recovered from liquid media using an external magnetic field. Adsorption experiment shows the magnetic hybrid material possesses a high adsorption capacity (118.6 mg g⁻¹), and has high adsorption efficiency (94.3%) after five adsorption cycles with ethanol (0.2% HCl) as eluent. The sorption kinetics and isotherm analysis indicate these sorption processes are better fitted to the pseudo‐second‐order and Langmuir equations. Thermodynamic study shows the sorption processes are spontaneous and endothermic.     

Ag/AgBr/Co–Ni–NO3 Layered Double Hydroxide Nanocomposites with Highly Adsorptive and Photocatalytic Properties

A facile anion‐exchange precipitation method was used to synthesize bifunctional Ag/AgBr/Co–Ni–NO₃ layered double hydroxide (LDH) nanocomposites by adding AgNO₃ solution to a suspension of Co–Ni–Br LDH. The Ag/AgBr nanoparticles were highly dispersed on the sheets of Co–Ni–NO₃ LDH. The prepared nanocomposites were used to adsorb and photocatalytically degrade organic pollutants from water. Without light illumination, the nanocomposites quickly adsorbed methyl orange, and the adsorptive capacity, which can reach 230 mg g^?1, is much higher than those of Co–Ni–Br LDH, Ag/AgBr, and activated carbon. The photocatalytic activities of the nanocomposites for the removal of dyes and phenol are higher than those of Co–Ni–Br LDH and Ag/AgBr. The proposed method can be applied to prepare other LDH/silver salt composites. The high absorptive capacity and good photocatalytic activity of such nanostructures could have wide applications in wastewater treatment.     

Fabrication and characterization of CMC‐based magnetic superabsorbent hydrogel nanocomposites for crystal violet removal

In this research work, novel magnetic superabsorbent hydrogel nanocomposites (MSHNs) based on carboxymethyl cellulose were prepared via a facile “one‐pot” two step approach. Magnetic iron oxide nanoparticles were in situ synthesized and incorporated into carboxymethyl cellulose/poly(acrylic acid) polymer hydrogel. The morphology and chemical composition of MSHNs as well as the presence of magnetic iron oxide nanoparticles were evaluated by using Fourier transform infrared, scanning electron microscopy, transmission electron microscopy, X‐Ray diffraction, ultraviolet–visible spectroscopy, thermogravimetric analysis, and vibrating sample magnetometer. The effect of different reaction parameters on the swelling capacity of MSHNs was investigated. Furthermore, batch adsorption experiments of crystal violet dye onto MSHNs were studied by varying solution pH, initial dye concentration, and temperature. Evaluation of thermodynamic parameters of crystal violet adsorption confirmed that the adsorption was spontaneous and endothermic process in nature. The equilibrium study revealed that the dye adsorption behavior of MHSNs followed the Redlich‐Peterson isotherm model. Finally, the dye adsorption experiment data was well fitted by the pseudo‐second‐order kinetic model with the regression coefficient (R²) of 0.9979. Our results suggest that the MHSNs with facile preparation method, high swelling capacity, and high dye adsorption capacity may be used as promising adsorbents for fast removal of various dyes from aqueous solutions. Copyright © 2016 John Wiley & Sons, Ltd.     

Ultrasound-assisted enhanced and rapid uptake of anionic dyes from the binary system onto MnFe2O4/polyaniline nanocomposite at neutral pH

Remediation of toxic dyes from an aqua matrix using novel nanocomposites as adsorbent is an attractive yet challenging task, especially when the adsorption process needs to be operated at near-neutral solution pH. Recently, conducting polymer-based novel nanocomposites have been studied widely for environmental remediation because of their high distinctive surface area, mesoporous nature, easy synthesis process, availability of the low-cost monomer, and comprehensive range of functionality. This research deals with the fabrication and application of manganese ferrite and polyaniline nanocomposite (MnF-PANI-NC) for the ultrasound-assisted adsorption of methyl red (MR) and congo red (CR) dye from binary dye solution at neutral pH. The X-ray diffraction pattern of MnF-PANI-NC confirmed the successful impregnation of manganese ferrite onto polyaniline, and the field emission gun scanning electron microscopy and transmission electron microscopy images revealed the nanoscale formation of this composite. The saturation magnetization of ~20 emu/g endorses the easy magnetic separation of MnF-PANI-NC from dye solution. MnF-PANI-NC has revealed higher adsorptive affinity towards MR and CR dye concerning pure PANI and pure MnF nanoparticles at near-neutral solution pH. Assimilation of ultrasound wavse in this adsorption procedure improved the mass transfer rate significantly, and within 6 min of reaction more than 95% of MR and CR dye removal was achieved. Ultrasound waves also enhanced the equilibrium dye uptake efficiency (more than 95%) of MnF-PANI-NC compared to the adsorption reaction by overhead stirring (40–50%) and shaking (40–60%) for both MR and CR dyes. Kinetic modeling of the experimental data revealed accurate fitting of the pseudo-second-order model in association with intraparticle diffusion. Binary dye adsorption onto MnF-PANI-NC obeyed the Langmuir isotherm model accurately, and maximum adsorption capacities of 294.12 and 317.46 mg/g were observed for MR and CR dyes, respectively.     

Preparation of magnetic molecularly imprinted polymer nanoparticles by surface imprinting by a sol–gel process for the selective and rapid removal of di‐(2‐ethylhexyl) phthalate from aqueous solution

Magnetic molecularly imprinted polymer nanoparticles for di‐(2‐ethylhexyl) phthalate were synthesized by surface imprinting technology with a sol–gel process and used for the selective and rapid adsorption and removal of di‐(2‐ethylhexyl) phthalate from aqueous solution. The prepared magnetic molecularly imprinted polymer nanoparticles were characterized using Fourier transform infrared spectroscopy, scanning electron microscopy, thermogravimetric analysis, and vibrating sample magnetometry. The adsorption of di‐(2‐ethylhexyl) phthalate onto the magnetic molecularly imprinted polymer was spontaneous and endothermic. The adsorption equilibrium was achieved within 1 h, the maximum adsorption capacity was 30.7 mg/g, and the adsorption process could be well described by Langmuir isotherm model and pseudo‐second‐order kinetic model. The magnetic molecularly imprinted polymer displayed a good adsorption selectivity for di‐(2‐ethylhexyl) phthalate with respect to dibutyl phthalate and di‐n‐octyl phthalate. The reusability of magnetic molecularly imprinted polymer was demonstrated for at least eight repeated cycles without significant loss in adsorption capacity. The adsorption efficiencies of the magnetic molecularly imprinted polymer toward di‐(2‐ethylhexyl) phthalate in real water samples were in the range of 98–100%. These results indicated that the prepared adsorbent could be used as an efficient and cost‐effective material for the removal of di‐(2‐ethylhexyl) phthalate from environmental water samples.     

Synthesis and application of treated activated carbon for cationic dye removal from modelled aqueous solution

Use of activated carbon (AC) prepared from rice husk and treated with anionic surfactant is investigated to eliminate cationic dye crystal violet (CV) using modelled dye solution. AC modified with anionic surfactant sodium lauryl sulfate (ACSLS) and other two surfactant namely sodium dodecyl sulfonate and hexadecyl trimethyl ammonium bromide were used for the analysis. Optimum ACSLS was analyzed and characterized using BET, XRD, SEM accompanied with XEDS, FTIR, HR-TEM and zeta potential, which confirms the sorption of CV onto ACSLS. Influence of pH, dose of adsorbent, concentration of initial dye, contact time, additive salts as well as actual water samples were investigated. Presence of NH⁴⁺, Ca²⁺, Mg²⁺, Na²⁺, Ca²⁺ and K⁺ cations in dye solution were having negligible (less than 4 %) influence on dye removal capacity. Study of mass transfer parameters revealed intra particle diffusion and film diffusion both played their part, whereas other kinetic studies has shown that experimental data fitted best with Pseudo 2nd order rate. Isotherm studies accompanied with error analysis revealed that Langmuir isotherm controls the adsorption equilibrium with highest capacity of CV adsorption with optimum operating conditions as pH = 6, temperature = 318 K, adsorbent dose = 100 mg/L and dye concentration = 30–60 mg/L. Study of thermodynamics and temperature analysis have shown that the sorption reaction was favourable and spontaneous with rise in temperature and endothermic in nature. Column studies are reported for varying rate of flow, depth of bed and dye concentrations along with analysis of column experimental data with various models like Yoon-Nelson, Thomas, Bohart-Adam and Clark model. Reusability (no. of cycles) of used adsorbent was studied using regeneration experiments. Analysis inferred that AC modified using surfactants can be a useful technique for enhanced adsorption capacity of dyes from aqueous solution and not much work has been reported on use of anionic surfactant modified AC for dye removal process.     

Removal of Mn(II) from Acidic Wastewaters Using Graphene Oxide–ZnO Nanocomposites

Pollution due to acidic and metal-enriched waters affects the quality of surface and groundwater resources, limiting their uses for various purposes. Particularly, manganese pollution has attracted attention due to its impact on human health and its negative effects on ecosystems. Applications of nanomaterials such as graphene oxide (GO) have emerged as potential candidates for removing complex contaminants. In this study, we present the preliminary results of the removal of Mn(II) ions from acidic waters by using GO functionalized with zinc oxide nanoparticles (ZnO). Batch adsorption experiments were performed under two different acidity conditions (pH1 = 5.0 and pH2 = 4.0), in order to evaluate the impact of acid pH on the adsorption capacity. We observed that the adsorption of Mn(II) was independent of the pH_PZC value of the nanoadsorbents. The qmax with GO/ZnO nanocomposites was 5.6 mg/g (34.1% removal) at pH = 5.0, while with more acidic conditions (pH = 4.0) it reached 12.6 mg/g (61.2% removal). In turn, the results show that GO/ZnO nanocomposites were more efficient to remove Mn(II) compared with non-functionalized GO under the pH2 condition (pH2 = 4.0). Both Langmuir and Freundlich models fit well with the adsorption process, suggesting that both mechanisms are involved in the removal of Mn(II) with GO and GO/ZnO nanocomposites. Furthermore, adsorption isotherms were efficiently modeled with the pseudo-second-order kinetic model. These results indicate that the removal of Mn(II) by GO/ZnO is strongly influenced by the pH of the solution, and the decoration with ZnO significantly increases the adsorption capacity of Mn(II) ions. These findings can provide valuable information for optimizing the design and configuration of wastewater treatment technologies based on GO nanomaterials for the removal of Mn(II) from natural and industrial waters.     

Adsorptive scavenging of cationic dyes from aquatic phase by H3PO4 activated Indian jujube (Ziziphus mauritiana) seeds based activated carbon: Isotherm,kinetics, and thermodynamic study

In the present work, a cost-effective Indian jujube seeds derived activated carbon (IJSAC) prepared via o-phosphoric acid chemical activation, is studied for the sequestration of acriflavine (AF) and Victoria blue B (VB) from the aquatic environment. The activated carbon is characterized by Fourier transform infrared spectroscopy, N₂-adsorption/desorption isotherm, scanning electron microscopy techniques and point of zero-charge measurement. The specific surface area (S_BET) of 571 m²/g with a pore radius of 22.45 Å specifies mesoporous nature of the IJSAC. The implication of operational conditions on the adsorption of both dyes onto IJSAC assessed by batch methodology, establish the optimal conditions as dosage (1.5 and 2.5 g/L), contact time (60 min), pH (8 and 10), and initial concentration (130 and 140 mg/L) for AF and VB uptake, respectively. The Freundlich adsorption isotherm model (R² = 0.99) appropriates the equilibrium data suggesting multilayer adsorption onto heterogeneous surface sites, while pseudo-second order (R² = 0.95–0.99) is the best fit kinetic model. The liquid film and intraparticle diffusion modelling demonstrate that the adsorption process of these dyes is governed by both the steps. Maximum Langmuir adsorption capacity is 113.6 mg/g for acriflavine and 92.78 mg/g for Victoria blue B. Thermodynamic studies indicate endothermic and spontaneous adsorption of dyes. The adsorption mechanism for the uptake of AF and VB by IJSAC most probably involves hydrogen bonding, electrostatic and π-π interactions. Based on its high adsorption capacity, relatively faster kinetics, and reusability, IJSAC can be perceived as a proficient and effective adsorbent for cationic dyes removal from the liquid waste.     

Ultrasound-aided rapid and enhanced adsorption of anionic dyes from binary dye matrix onto novel hematite/polyaniline nanocomposite: Response surface methodology optimization

In recent times, polyaniline (PANI), a conducting polymer, has been studied widely for environmental remediation application due to its controllable electric conductivity with high surface area, which makes it a suitable adsorbent material. But lower mechanical stability of PANI is considered to be a serious drawback for its large-scale industrial application. To improve the mechanical strength of PANI, in this study, hematite nanoparticles were impregnated onto PANI by oxidative polymerization method in order to fabricate a novel organometallic nanocomposite (hematite-PANI-NC). The hematite-PANI-NC was used as adsorbent for removal of methyl orange (MO) and eosin yellow (EY) dye from binary dye matrix under ultrasonic-assisted adsorption. Excellent MO and EY dye removal (more than 98%) was observed from binary matrix at a wide solution pH from 2.0 to 6.0, and under ultrasound wave the adsorption equilibrium was achieved within 15 min only. Both MO and EY dyes adsorption experimental data strictly followed Langmuir isotherm, and maximum monolayer adsorption capacity of 126.58 mg/g and 112.36 mg/g was observed for MO and EY dye, respectively. The uptake mechanism of MO and EY dyes onto hematite-PANI-NC is governed by electrostatic interaction, π-π bonding and hydrogen bonding between dye molecules and nanocomposite. Response surface methodology analysis reveals maximum MO and EY removal of 98.43% and 99.35% at optimum experimental conditions. This study implies that the hybrid organometallic material hematite-PANI-NC has high potential for quick and enhanced sono-assisted uptake of anionic dyes from water near neutral solution pH.     

Sorption of Pb(Ⅱ) on Mg-Fe Layered Double Hydroxide

Mg‐Fe layered double hydroxide (LDH) with a Mg/Fe molar ratio of 3:1 was synthesized by using a coprecipitation method and the sorption removal of Pb(II) by the LDH sample from Pb(NO₃)₂ solution was investigated. It was found that Mg‐Fe LDH showed a good sorption ability for Pb(II) from Pb(NO₃)₂ solution, indicating that the use of LDH as a promising inorganic sorbent for the removal of heavy metal ions is possible. The sorption kinetics and the sorption isotherm of Pb(II) on the LDH sample obeyed the pseudo‐second order kinetic model and Aranovich‐Donohue equation, respectively. The sorption mechanism of Pb(II) on the LDH may be attributed to the surface‐induced precipitation and the chemical binding adsorption, and the removal ability arising from the surface‐induced precipitation is much higher than that from the chemical binding adsorption.     

Kinetic and equilibrium adsorption of methylene blue and remazol dyes onto steam-activated carbons developed from date pits

Steam-activated carbons DS2 and DS5 were prepared by gasifying 600 °C-date pits carbonization products with steam at 950 °C to burn-off = 20 and 50%, respectively. The textural properties of these carbons were determined from the nitrogen adsorption at ?196 °C. The chemistry of the carbon surface was determined from the surface pH and from neutralization of the surface carbon–oxygen groups of basic and acidic type. The kinetic and equilibrium adsorption of MB and RY on DS2 and DS5 was determined at 27 and 37 °C and at initial sorption solution pH 3–7.DS2 and DS5 have expanded surface area, large total pore volume and contain both micro and mesoporosity. They have on their surface basic and acidic groups of different strength and functionality. This enhanced the sorption of the cationic dye (MB) and of the anionic dye (RY). The adsorption of MB and RY on DS2 and DS5 involves intraparticle diffusion and followed pseudo-second order kinetics. The adsorption isotherms were applicable to the Langmuir isotherm and high monolayer capacities for MB and RY dyes were evaluated indicating the high efficiencies of the carbons for dye adsorption.     

Development of hybrid adsorbent for effective aqueous phase sorptive removal of copper

Alginate beads (ABs) immobilized with hydrous zirconium oxide (ZO) were used as a hybrid adsorbent (ZO@AB) for the effective removal of copper ions [Cu(II)] from aqueous phase. ZO@AB was characterized using X‐ray photoelectron spectroscopy to confirm the impregnation of ABs with ZO and the adsorption of Cu(II) onto ZO@AB. The maximum equilibrium sorption capacity of ZO@AB for Cu(II) was 63.1 mg·g⁻¹ at pH 5. The Cu(II) removal rate was high at the beginning of reaction, with >90% adsorption within 24 hours, and equilibrium was achieved within 48 hours. The adsorption of Cu(II) onto ZO@AB was well described by pseudo‐second‐order kinetic model (R² > 0.99), and the monolayer nature of sorption was supported by the Langmuir model (R² > 0.99). The sorption process was endothermic, favorable, and spontaneous in nature. Regarding the reusability of the adsorbent, its sorption capacity remained satisfactory (>90%) throughout the 5 consecutive cycles (regeneration in 0.1 mol·L⁻¹ HCl). The stoichiometric ratio of released calcium ions [Ca(II)] to adsorbed copper ions [Cu(II)] was approximately 1:1, confirming that ion exchange was the main mechanism for removal of Cu(II) from aqueous phase. The developed adsorbent (ZO@AB) shows promise as a candidate for the effective and selective removal of Cu(II) from aqueous phase.     

Polyethyleneimine-grafted polyphosphazene microspheres for rapid and efficient capture of anionic dyes from wastewater

Developing novel adsorbent to capture organic contaminants from wastewater rapidly and efficiently is highly desirable for waste treatment and environmental restoration. Herein, we reported a new amino-rich spherical adsorbent (PZS-PEI) for highly-efficient uptake of anionic dyes from aqueous solution. The PZS-PEI adsorbent was fabricated through a two-step process including synthesis of PZS-Cl microspheres via room temperature polymerization of hexachlorocyclotriphosphazene with bis(4-hydroxyphenyl) sulfone and subsequent surface grafting reaction of PZS-Cl microspheres using branched polyethyleneimine (PEI). The microstructure of as-obtained PZS-PEI microspheres was fully characterized by scanning electron microscopy, Fourier transform infrared, X-ray photoelectron spectroscopy, zeta potential, and N₂ adsorption test. The adsorption performance of the PZS-PEI microspheres towards organic dyes was evaluated through carrying out a series of studies including various influence factor analysis, adsorption isotherm, kinetics, and thermodynamics. Results show that the PZS-PEI adsorbent owned good adsorption selectivity towards anionic dyes, and the maximum adsorption capacities for methyl orange (MO), acid chrome blue K, eosin-Y reached 190.29, 152.90, and 92.34 mg/g at 25 °C, respectively. In addition, the uptake behavior of organic dye by the PZS-PEI adsorbent conformed to Freundlich isotherm and pseudo-second order kinetic model, and the adsorption process followed a three-stage intraparticle diffusion mode with an endothermic and spontaneous characteristic. Electrostatic interaction and hydrogen bonding were responsible for the highly-efficient adsorption of the PZS-PEI adsorbent towards typical anionic dye MO.     

Magnetically separable ZnO/ZnFe2O4 and ZnO/CoFe2O4 photocatalysts supported onto nitrogen doped graphene for photocatalytic degradation of toxic dyes

Advanced oxidation processes (AOPs) counting heterogeneous photocatalysis has confirmed as one of the preeminent method for waste water remediation. In the present work, we have successfully fabricated novel visible-light-driven nitrogen-doped graphene (NG) supported magnetic ZnO/ZnFe₂O₄ (ZnO/ZF/NG) and ZnO/CoFe₂O₄ (ZnO/CF/NG) nanocomposites. ZnO synthesized via direct precipitation method. Hydrothermal method was used for the preparation of nitrogen-doped graphene supported magnetic ZnO/ZF (ZnO/ZnFe₂O₄) and ZnO/CF (ZnO/CoFe₂O₄) nanocomposites. The procured materials were scrutinized by assorted characterizations to acquire information on their chemical composition, crystalline structure and photosensitive properties. The absorption and photocatalytic performance of photocatalysts were studied via UV–Visible spectra. Photodegradation performance of the synthesized nanocomposites was estimated toward mineralization of methyl orange (MO) and malachite green (MG) dyes in aqueous solution. The high surface area of ZnO/ZF/NG and ZnO/CF/NG was suitable for adsorptive removal of MO and MG dyes. The photodegradation performance of heterojunction photocatalysts was superior to bare photocatalyst in 140 min under visible-light irradiation. Spectrophotometer, GC–MS (Gas chromatography–mass spectrometry) elucidation was carried out to expose the possible intermediates formed. Both ZnO/ZF/NG and ZnO/CF/NG were rapidly isolated from the aqueous phase by applying an external magnetic field in 20 sec and 2 min, respectively. The photocatalytic performance and stability of ZnO/ZF/NG and ZnO/CF/NG nanocomposites were confirmed by conducting 10 consecutive regeneration cycles. Owing to recyclability of ZnO/ZF/NG and ZnO/CF/NG, these heterogeneous nanocomposites might be used as cost-effective for treatment of discarded water. The observations endorse that the synthesized ternary heterogeneous nanocomposites facilitates wastewater decontamination using photocatalytic technology.     

Preparation of ferric nitrate–graphene nanocomposite and its adsorption of arsenic(V) from simulated arsenic‐containing wastewater

Ferric nitrate–graphene (FG) nanocomposites synthesized via the equivalent‐volume impregnation method were used for the removal of As(V) species from simulated arsenic‐containing wastewater. Effects of various factors were assessed, such as the reaction temperature, solution pH, adsorbent dosage, and reaction time. The results indicated that the As(V) removal efficiency was as high as 99%, and the concentration of arsenic‐containing wastewater after FG treatment was as low as 9.4 μg L^–1 as a result of the optimal absorption capacity and maximum specific surface area (171.766 m²/g) of this material. The equilibrium adsorption capacity of FG for As(V) was achieved in approximately 20 min, and the maximum adsorption capacity was calculated to be 112.4 mg g^–1 by Langmuir adsorption isotherm, which was higher than that of other adsorbents such as manganese‐incorporated iron(III) oxide–graphene (14.42 mg g^–1). Moreover, the removal efficiency of As(V) can be maintained above 95% under acidic and alkaline conditions. Brunauer–Emmett–Teller analysis showed that the modified FG pore structure was regular. Based on the characterizations by X‐ray diffraction, X‐ray photoelectron spectroscopy, and Fourier transform infrared, the products on the surface of the used FG were Fe(OH)₃, FeAsO₄, and other compounds, and As(V) was mainly removed by the formation of insoluble compounds and coprecipitation.     

Sorption Removal of Pb（Ⅱ） from Solution by Uncalcined and Calcined MgAl-Layered Double Hydroxides

Layered double hydroxide （LDH） with a Mg/Al molar ratio of 1 ： 1 was synthesized by using a co-precipitation method and its calcined product （CLDH） was obtained by calcination of the MgAl-LDH at 500 ℃. The sorption removal of Pb^2＋ from solution was investigated, finding that both LDH and CLDH show good sorption ability and they could be used as a new type of environmental sorbent for the removal of Pb^2＋ from water. The sorption kinetics and the sorption isotherms of Pb^2＋ on both LDH and CLDH can be described by the pseudo-second order kinetics and Freundlich isotherm, respectively, under the studied conditions. The sorption amounts of Pb^2＋ on LDH and CLDH are independent of pH in a pH range of about 3-10. The presence of NaNO3 may inhibit the sorption of Pb^2＋ on LDH while hardly affect that on CLDH. The sorption mechanism of Pb^2＋ on LDH and CLDH may be attributed to the surface precipitation and the surface complex adsorption. The surface complex adsorption may be further distinguished to the chemical binding adsorption forming the inner-sphere surface complexes and the electrostatic binding adsorption forming the outer-sphere surface complexes. The sorption mechanism of Pb^2＋ on LDH may be attributed to the surface precipitation and the electrostatic binding adsorption, while that on CLDH may be attributed to the surface precipitation and the chemical binding adsorption.     

A simple method for removal of toxic dyes such as Brilliant Green and Acid Red from the aquatic environment using Halloysite nanoclay

This project explains an easy, simple and eco-friendly method to remove some toxic dyes like Brilliant Green and Acid Red from aquatic solution by technique of solid-phase extraction that uses Halloysite nanoclay eco-friendly solid phase as absorbent surface for adsorption of dye. The physical properties of the HNC such as scanning electron microscopy, transmission electron microscope, X-ray diffraction, Fourier transform infrared spectroscopy, and surface area analysis were studied. The best conditions like pH of the solution, HNC weight, contact shaking time, the temperature of the solution, and ionic strength were investigated for removal effectiveness. The experimental data of the adsorption process showed that HNC can remove most of the dyes within 30 min, with an adsorption capacity of 12.5 mg/g for A.R dye and 13.9 mg/g for B.G dye on HNC solid phase at optimum conditions. The removal process of dyes on HNC was studied kinetically and thermodynamically, and the data confirms that the pseudo-second-order kinetic model was able to describe the adsorption process. Thermodynamic data confirms the process was spontaneous andexothermic in nature for A.R dye, while was spontaneous and endothermic in nature for B.G dye. Finally, the effectiveness of HNC was inspected by removing dyes from three various real samples, and the results showed high performance in removing dyes on HNC for four consecutive cycles.