甲醇在欠电位沉积Sn/Pt电极上催化氧化

在欠电位沉积（upd）锡修饰的铂电极（upd-Sn/Pt）上,对甲醇电化学催化氧化过程进行了研究.发现当Pt表面upd-Sn的覆盖率在20％附近时,对甲醇的催化氧化的增强作用最为明显；在电位低于0.35 V （vs RHE）时,甲醇在Pt与upd-Sn/Pt电极上氧化只进行到脱氢生成CO的步骤;在0.35 V以后,表面Sn－OH形成,反应Sn－OH＋COads=Sn＋CO2＋H＋＋e有利于表面CO的去除;而Pt电极上,只有0.6 V以后,才有反应Pt－OH＋COads=Pt＋CO2＋H＋＋e发生.因此,Sn的存在有利于甲醇在较低的电位下氧化; Pt电极上CH3OH脱氢并释放出电子的过程是一个快速的过程,表面CO的去除是甲醇氧化过程的控制步骤;甲醇氧化产生的表面吸附态CO 以线式吸附为主,少量的桥式吸附态CO在反应初期即达到吸附饱和; Pt表面上upd-Sn表现的催化增强作用,在光亮铂电极和在高分散铂黑电极上是一致的.     

Ru膜上Pt层的自发沉积及其在电化学表面增强红外光谱中的应用

采用自发沉积法在Ru膜上生成超薄Pt层(简称Ru/Pt膜), 即在开路状态下将电化学还原后的Ru膜浸于除去氧的H2PtCl6溶液中进行自发沉积. 电化学伏安法测量表明, 随着电还原-自发沉积循环次数的增加, 该Ru/Pt膜电极所含Pt组分增加, 且CO吸附层的电氧化峰电位较Pt膜电极上的明显负移. 应用现场衰减全反射表面增强红外光谱法(ATR-SEIRAS)可轻易检测到在该膜电极Pt和Ru位上吸附CO的振动谱峰. 所制Ru/Pt膜电极不仅对CO的电催化氧化具有协同效应, 还可应用于现场ATR-SEIRAS的研究中.     

纤维蛋白原在Pt电极上的界面电化学研究

应用电化学方法和电化学原位红外反射光谱(electrochemical in-situ FTIR)等研究了纤维蛋白原在Pt电极上的界面电化学行为.结果表明:纤维蛋白原在Pt电极上的吸附使电极的析氢与氧脱附过程减弱,影响程度随扫速的增加而增强;同样纤维蛋白原的吸附会降低亚铁氰化钾-铁氰化钾电对的氧化还原反应可逆性和电流;在-0.1~0.6V(vs.SCE)扫描范围内没有出现纤维蛋白原的特征"氧化还原"峰.电化学原位红外反射光谱测试表明纤维蛋白原在0.3~0.5V(vs.SCE)间发生化学反应,有新的产物生成.     

PtRu/C电催化剂上甲醇吸附氧化过程的电化学原位红外光谱

采用调变的多元醇法制备了高分散的Pt/C, PtRu/C和Ru/C电催化剂. XRD计算结果表明, PtRu/C电催化剂的平均粒径和合金度分别为2.2 nm和71%. 采用电化学方法和原位傅里叶变换红外反射光谱方法(in situ FTIRS)研究了甲醇在3种电催化剂上的吸附氧化过程, 发现PtRu/C对甲醇的催化活性明显高于Pt/C, Ru的加入一方面影响了甲醇在Pt上的解离吸附性能, 另一方面提供了Ru-OH物种, 从而抑制了低电位下电催化剂中毒. 红外光谱研究结果表明, 线性吸附态CO(COL)是主要毒化物种, 反应产物主要是CO2, 还有少量的甲酸甲酯. 根据实验结果讨论了甲醇在PtRu/C电催化剂上的氧化机理.     

二十四面体Pt纳米晶电极上甲酸解离吸附反应动力学研究

研究了甲酸在二十四面体Pt纳米晶（THHPtNCs）电极表面解离吸附反应过程.电化学原位红外反射光谱结果显示,甲酸在低电位（-0.20V（SCE））即可在THHPtNCs电极上氧化到CO2,同时发生分子内化学键断裂生成吸附态CO物种.运用程序电位阶跃暂态方法定量研究甲酸解离吸附反应动力学,测得5×10^-3mol·L^-1 HCOOH＋0.1mol·L^-1 H2SO4溶液中甲酸在THHPtNCs电极上解离吸附的最大平均速率υamax为13.19×10^-10mol·cm^-2·s^-1,是商品Pt/C催化剂电极上υamax的1.5倍.研究结果揭示了THHPtNCs的反应活性显著高于Pt/C催化剂.     

铂单晶电极表面不可逆反应动力学──Ⅰ.Pt(100)单晶电极上甲酸氧化的现场红外反射光谱研究

运用电化学暂态方法和现场时间分辨FTIR反射光谱研究甲酸在Pt（100）单晶电极上的解离吸附和氧化过程．深入认识了甲酸解离吸附的反应速率在-0．25至0．25V电位区间呈火山形变化的规律．根据电化学现场时间分辨红外光谱的研究结果，提出在研究反应动力学时避免甲酸解离吸附干扰的方法，为进一步研究甲酸在Pt（100）电极表面经活性中间体直接氧化至CO2的反应动力学奠定了基础．     

甲酸在Pt-Ru/GC电极上氧化的SERS研究

采用循环伏安(CV)法、计时电流法和电化学原位表面增强拉曼散射光谱(SERS)技术研究了甲酸在Pt-Ru/GC电极上的氧化行为, 发现甲酸在Pt-Ru/GC电极上与在粗糙Pt电极上一样, 也能自发解离出强吸附中间体CO和活性中间体—COO－. 从分子水平证实钌的加入有利于提高电极对甲酸的电催化氧化活性, 当镀液中Pt：Ru的摩尔比从10∶1变化到1∶1, CO的氧化峰电位从0.41 V负移至0.35 V, 约负移了60 mV. Pt-Ru/GC(1∶1)电极与粗糙Pt电极相比, CO在电极表面氧化完毕的电位亦负移了约200 mV. 该研究结果表明, 电化学原位表面增强拉曼散射光谱技术可望成为研究电催化反应机理的普适谱学工具.     

甲醇在欠电位沉积Ru修饰Pt电极上的催化氧化

采用欠电位沉积(upd)方法在Pt 表面沉积亚单层的Ru制备出upd-Ru/Pt 电极. 通过欠电位沉积前后电极在0.5 mol·L-1 H2SO4溶液中循环伏安图-152 - 128 mV(vs Ag/AgCl)电位范围内对氢区的数值积分确定Pt表面Ru 的覆盖度. 用电化学方法测试了甲醇在upd-Ru/Pt电极上的催化氧化, 并讨论分析了欠电位沉积电位和Ru的表面覆盖度对甲醇氧化的影响. 结果表明, Ru能够欠电位沉积到Pt表面. Pt表面欠电位沉积少量的Ru 即能大大促进甲醇的氧化.只要控制upd-Ru的沉积量, upd-Ru原子就能大大促进甲醇氧化而与沉积电位无关. Ru原子对甲醇氧化的促进作用与Ru和Pt是否形成合金无关, 而取决于Ru 在Pt表面的百分含量.     

Pt电极表面共吸附层NO和CO氧化还原的CV及原位FTIR研究

应用电化学循环伏安方法（CV）和原位傅里叶变换红外反射光谱（in situ FTIRS）研究了酸性溶液中Pt多晶电极表面NO和CO的共吸附行为及吸附态CO对吸附物种NO氧化还原反应的影响．研究结果表明,0．20V（VS．SCE）时,CO和NO能同时稳定吸附在Pt电极表面,CO以线性吸附态（CO L）存在,NO以桥式吸附态（NOB）和线性吸附态（NO L）共存．CO L 的共存使得NO的还原电流峰电位负移约0．024V,并且促使不易被氧化的NO B在0．93V处被氧化．原位FTIRS研究进一步表明,NO可以置换预吸附在电极表面的CO,NO和CO在Pt多晶电极表面的吸附是一个竞争吸附的过程．在0．45V-1．2V电位区间,NO和CO都能转化为环境友好产物,分别为NO3-和CO2．且Pt电极表面共吸附物种CO的量直接影响NO B的氧化产物NO3-的生成量．     

Pt及其修饰电极上甲醇吸附和氧化的CV和EQCM研究

运用电化学循环伏安和石英晶体微天平 (EQCM )研究了 0 .1mol·L- 1H2 SO4 溶液中甲醇在Pt电极和以Sb ,S不可逆吸附原子修饰的Pt(Pt/Sbad和Pt/Sad)电极上的吸附和氧化过程 .结果表明甲醇的氧化与电极表面氧物种有着极其密切的关系 .Pt电极表面Sb吸附原子能在较低的电位下吸附氧 ,可显著提高甲醇电催化氧化活性 .与Pt电极相比较 ,Sb吸附原子修饰的Pt电极使甲醇氧化的峰电位负移了 0 .13V .相反 ,Pt电极表面S吸附原子的氧化会消耗表面氧物种 ,抑制了甲醇的电氧化 .本文从表面质量变化提供了吸附原子电催化作用的新数据     

Irrelevance of Carbon Monoxide Poisoning in the Methanol Oxidation Reaction on a PtRu Electrocatalyst

Based on detailed in situ attenuated total‐reflection–surface‐enhanced IR reflection absorption spectroscopy (ATR‐SEIRAS) studies of the methanol oxidation reaction (MOR) on Ru/Pt thin film and commercial Johnson–Matthey PtRu/C, a revised MOR enhancement mechanism is proposed in which CO on Pt sites is irrelevant but instead Pt‐Ru boundary sites catalyze the oxygen insertion reaction that leads to the formation of formate and enhances the direct reaction pathway.     

酸性溶液中过渡金属及合金纳米薄膜电极的异常红外效应研究

以循环伏安方法在玻碳载体上制备纳米级厚度的过渡金属 (Pt,Pd ,Rh ,Ru)和合金 (PtPd ,PtRu)薄膜电极 ,并运用原位FTIR反射光谱研究了CO的吸附过程 .发现所制备的纳米薄膜电极均具有异常红外效应 ,即与本体金属电极相比较 ,吸附在纳米薄膜电极上的CO分子的红外吸收被显著增强 ,并且红外谱峰方向倒反 .本文的结果进一步证明异常红外效应是一种新的、普遍的现象 ,主要取决于过渡金属或合金膜的结构和厚度 .对异常红外效应的深入认识 ,不仅将推动红外反射光谱及界面电化学理论的发展 ,而且将在表面和界面分析中得到广泛应用 .     

Pt-Ru合金薄膜的电沉积制备及其电化学表面增强红外吸收光谱

在1mmol·L-1H2PtCl6+1mmol·L-1RuCl3+0.1mol·L-1H2SO4镀液中采用电沉积法在化学镀金膜的红外窗口Si反射面上制备Pt50Ru50合金电极.利用原子力显微镜(AFM)可以观察到制备的Pt50Ru50合金电极形貌呈现出100-200nm大小的颗粒.常规电化学分析方法得出该电极具有典型的合金特征,对CO和CH3OH具有很好的催化氧化作用.应用电化学现场衰减全反射表面增强红外光谱法(ATR-SEIRAS)可以观察到该电极上Pt位和Ru位上CO的振动谱峰,且表现出Pt-Ru二元金属良好的协同催化性能.     

Simple replacement reaction for the preparation of ternary Fe(1-x)PtRu(x) nanocrystals with superior catalytic activity in methanol oxidation reaction

The finding of new metal alloyed nanocrystals (NCs) with high catalytic activity and low cost to replace PtRu NCs is a critical step toward the commercialization of fuel cells. In this work, a simple cation replacement reaction was utilized to synthesize a new type of ternary Fe(1-x)PtRu(x) NCs from binary FePt NCs. The detailed structural transformation from binary FePt NCs to ternary Fe(1-x)PtRu(x) NCs was analyzed by X-ray absorption spectroscopy (XAS). Ternary Fe(35)Pt(40)Ru(25), Fe(31)Pt(40)Ru(29), and Fe(17)Pt(40)Ru(43) NCs exhibit superior catalytic ability to withstand CO poisoning in methanol oxidation reaction (MOR) than do binary NCs (FePt and J-M PtRu). Also, the Fe(31)Pt(40)Ru(29) NCs had the highest alloying extent and the lowest onset potential among the ternary NCs. Furthermore, the origin for the superior CO resistance of ternary Fe(1-x)PtRu(x) NCs was investigated by determining the adsorption energy of CO on the NCs' surfaces and the charge transfer from Fe/Ru to Pt using a simulation based on density functional theory. The simulation results suggested that by introducing a new metal into binary PtRu/PtFe NCs, the anti-CO poisoning ability of ternary Fe(1-x)PtRu(x) NCs was greatly enhanced because the bonding of CO-Pt on the NCs' surface was weakened. Overall, our experimental and simulation results have indicated a simple route for the discovery of new metal alloyed catalysts with superior anti-CO poisoning ability and low usage of Pt and Ru for fuel cell applications.     

Structures and catalytic properties of PtRu electrocatalysts prepared via the reduced RuO2 nanorods array

Structures and properties of PtRu electrocatalyts, derived from the aligned RuO2 nanorods (RuO2NR), are investigated using scanning electron microscopy, transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and cyclic voltammetry toward COads and methanol oxidation. The catalytic activity of methanol oxidation and the CO tolerance are promoted significantly by reducing RuO2 into Ru metal before decorating with Pt. Reduction of RuO2NR was carried out by either thermal decomposition at 650 degrees C in vacuum or H2-reduction at 130 degrees C in low-pressure hydrogen. Reduction assisted by hydrogen allows infiltrating decomposition at low temperature and produces an array of nanorods with rugged walls featuring small Ru nuclei and larger surface area. Pt-RuNR, whose surface Pt:Ru ratio=0.58:0.42 was prepared by decorating with 0.1 mg cm(-2) Pt on the H2-reduced array containing 0.39 mg cm(-2) Ru, demonstrates a favorable combination of CO tolerance and high methanol oxidation activity superior to other RuO2NR-derived catalysts. When compared with a commercial electrocatalyst of PtRu (1:1) alloy (<4 nm), the activity of Pt-RuNR in methanol oxidation is shown to be somewhat lower at potential<0.48 V and higher at potential>or=0.48 V.     

In-situ X-ray absorption spectroscopy study of Pt and Ru chemistry during methanol electrooxidation

Methanol electrooxidation in a 0.5 M sulfuric acid electrolyte containing 1.0 M CH3OH was studied on 30% Pt/carbon and 30% PtRu/carbon (Pt/Ru = 1:1) catalysts using X-ray absorption spectroscopy (XAS). Absorption by Pt and Ru was measured at constant photon energy in the near edge region during linear potential sweeps of 10-50 mV/s between 0.01 and 1.36 V vs rhe. The absorption results were used to follow Pt and Ru oxidation and reduction under transient conditions as well as to monitor Ru dissolution. Both catalysts exhibited higher activity for methanol oxidation at high potential following multiple potential cycles. Correlation of XAS data with the potential sweeps indicates that Pt catalysts lose activity at high potentials due to Pt oxidation. The addition of Ru to Pt accelerates the rate of methanol oxidation at all potentials. Ru is more readily oxidized than Pt, but unlike Pt, its oxidation does not result in a decrease in catalytic activity. PtRu/carbon catalysts underwent significant changes during potential cycling due to Ru loss. Similar current density vs potential results were obtained using the same PtRu/carbon catalyst at the same loading in a membrane electrode assembly half cell with only a Nafion (DuPont) solid electrolyte. The results are interpreted in terms of a bifunctional catalyst mechanism in which Pt surface sites serve to chemisorb and dissociate methanol to protons and carbon monoxide, while Ru surface sites activate water and accelerate the oxidation of the chemisorbed CO intermediate. PtRu/carbon catalysts maintain their activity at very high potentials, which is attributed to the ability of the added Ru to keep Pt present in a reduced state, a necessary requirement for methanol chemisorption and dissociation.     

Studies on State and Structure of Noble Metals in Electrocatalyst Made by Coprecipitation Method

The electrocatalysts of Pt/C,PtRu/C and Ru/C were prepared by the impregnation method.The facet characterization.The dispersion and the particle size for the catalysts were determined by means of X-ray diffraction and transmission electron microscopy,X-ray photoelectron spectroscopy was also used to analyze the state and the valency of the noble metals.The results show that the particle size was in nanometer range and the binary metals have come into being an alloy.The platinum in the catalysts existed in zero valency.The valency of the ruthenium on the surface is different from that in the body,while the ruthenium on the surface existed in oxide-form.PtRu/C and Pt/C are of good activity of the electrooxidation of hydrogen except Ru/C.PtRu/C is more tolerant of CO than Pt/C,and CO is only adsorbed on Pt.     

枝晶状Pt 薄膜的制备及其特殊红外效应

采用方波电位, 在10×10^-3 mol·L^-1 K₂PtCl₆+3×10^-4 mol·L^-1 PbAc₂+0.5 mol·L^-1 HClO₄溶液中, 于本体Pt 电极上电沉积制备出枝晶状Pt 薄膜. 随着沉积时间的增加, 枝晶长度逐渐由400 nm增加到900 nm, 且枝晶上的小晶粒(~10 nm大小)变得密集. 根据循环伏安(CV)曲线中氢吸脱附电量可得出Pt 薄膜具有中等粗糙度(C_r=9-36), 且电极表面的粗糙度随着沉积时间增加而增大. 观察到Pt 薄膜上吸附态CO的原位红外光谱具有明显的增强吸收效应, 当沉积时间为6 min 时所制得的枝晶Pt 电极的红外增强效应最大. CO呈现多种谱峰形状, 随着沉积时间的增加, 谱峰形状依次为左高右低的双极峰(类Fano 红外效应), 单极向下(表面增强红外吸收), 左高右低的双极峰, 单极向上(异常红外效应), 左低右高的双极峰和单极向下. 这表明纳米材料薄膜所呈现出的特殊红外性能, 与纳米材料的尺度和聚集状态等密切相关. 所制备的枝晶状Pt 薄膜有望为深入认识纳米材料的特殊红外性能提供一个良好的模型材料.     

Adsorption of CO on Ru and Pt blacks and catalysts and the possibility of its utilization for the determination of the ruthenium-free surface

Electrochemical voltammetric curves on Ru and Pt blacks of a different surface area were measured in potential intervals 0.05–1.05 V in pure 0.5 M H₂SO₄ and after CO adsorption. It was proved that after the CO adsorption, the outset of ruthenium oxidation is shifted by about 150 mV towards the positive potentials, e.g. to the region of oxidation of adsorbed CO. This fact made possible the determination of a double-layer charging current of Ru electrodes and, subsequently, also the determination of the amount of adsorbed hydrogen on the Ru surface. An evaluation of the amount of CO and hydrogen adsorption showed that the ratio of adsorbed CO:H on the Pt surface was about 1:1, while on Ru electrodes this ratio was around twice as large. The amount of hydrogen adsorbed on Ru blacks depends on the preliminary preparation of the electrodes. The CO adsorption could also be employed in the determination of a charging current of electrode double-layers during voltammetric oxidation of adsorbed hydrogen on ruthenium supported on Al₂O₃, SiO₂, or TiO₂ carriers. However, a similar determination of hydrogen adsorbed on the tin-modified Ru catalysts is not very reliable.