微波原位合成Ag NPs/MoS2复合材料及其电化学性能

二硫化钼纳米片(MoS₂)受到带电杂质、结构缺陷和易聚集等因素的影响,导致其电子转移性能下降,使其应用受限。将银纳米颗粒(Ag NPs)与少层MoS₂纳米片复合,可提升MoS₂纳米片的电化学性能。本研究创新性地采用微波还原法,使Ag NPs原位沉积于MoS₂,得到Ag NPs/MoS₂复合材料。结果表明,将Ag NPs/MoS₂复合材料修饰于丝网印刷电极(screen printed electrodes,SPE)后,测得的循环伏安(cyclic voltammetry,CV)曲线峰电流值为同浓度单一MoS₂修饰电极的1.8倍,方波伏安(square wave voltammetry,SWV)曲线峰电流值为单一MoS₂修饰电极的3.4倍,电化学阻抗谱(electrochemical impedance spectroscopy,EIS)的电子转移阻抗值(Ret)仅为167Ω,相比MoS₂/S...     

芦丁在铂纳米/碳纳米管修饰电极上电化学行为研究

通过电沉积的方式在多壁碳纳米管(MWCNTs)修饰玻碳电极表面上沉积铂(pt)纳米粒子,并运用循环伏安法(CV)、示差脉冲伏安法(DPV)探讨了芦丁在铂纳米/碳纳米管/玻碳电极上的电化学行为.实验结果表明,芦丁在该修饰电极上呈现一对良好氧化还原峰,其氧化峰电流与浓度在3.2×10(-8)～1.2×10(-5)mol/L...     

La(OH)_3纳米片修饰玻碳电极对鸟嘌呤和腺嘌呤的电催化氧化

以La(OH)3纳米片为修饰剂,制备了基于La(OH)3纳米片修饰玻碳电极(LNP/GCE)。采用循环伏安(CV)法研究了鸟嘌呤(G)和腺嘌呤(A)在该修饰电极上的电化学行为。实验结果表明,在HAc-NaAc缓冲溶液中,该修饰电极对G和A都表现出了良好的电催化性能。在最佳条件下,用差分脉冲伏安(DPV)法对G和A进行了测定,其氧化峰电流与G和A的浓度在0.1~10μmol/L范围内呈良好的线性关系,检测限(S/N=3)分别为0.01μmol/L和0.03μmol/L。将该修饰电极用于DNA中A和G的同时测定,获得较好结果。     

铂-钯纳米簇/石墨烯修饰电极的制备及其在氯霉素传感中的应用

通过电沉积法制备了铂-钯纳米簇/石墨烯修饰电极(Pt-Pd/RGO/GCE)。利用扫描电子显微镜(SEM)和X射线能量色散光谱(EDS)对铂-钯纳米簇/石墨烯修饰电极进行了表征;采用循环伏安法(CV)对修饰电极电化学性质进行了研究,探究了铂钯原子比例和电沉积圈数对制备修饰电极的影响,研究了修饰电极对氯霉素(CAP)电催化作用。利用示差脉冲伏安法(DPV)对CAP进行检测,在1.0×10~(-7)～4.0×10~(-4) mol·L~(-1)浓度范围内,CAP的还原峰电流和浓度呈良好的线性关系,相关系数(R)为0.997,检出限(S/N=3)为5.1×10~(-8 ) mol·L~(-1)。结果表明,该修饰电极可望用于实际样品中CAP的测定。     

基于纳米材料修饰的高灵敏性L-苯丙氨酸印迹溶胶-凝胶传感器的研究

将氧化锌纳米膜(ZnO-NFs)、多壁碳纳米管(MWNTs)、纳米铜颗粒(Cu-NPs)和印迹溶胶-凝胶聚合物(MIP)依次修饰到碳电极(CE)表面,制备了一种对L-苯丙氨酸具有特异识别能力的印迹电化学传感器.采用电子扫描显微镜(SEM)对各修饰电极进行形貌表征;采用循环伏安法(CV)、示差脉冲伏安法(DPV)、安培时...     

间苯二酚在TiO2-石墨烯修饰玻碳电极上的电化学行为及测定

制备了TiO2-石墨烯修饰玻碳电极。用循环伏安法(CV)和差分脉冲伏安法(DPV)对间苯二酚在该修饰电极的电化学行为进行了研究。实验结果表明,在pH值为6.0的磷酸盐缓冲液(PBS)中,该修饰电极对间苯二酚具有良好的电催化作用。对TiO2-石墨烯用量、支持电解质、pH和扫描速度等实验条件进行了优化。在优化条件下,利用DPV测定,间苯二酚的氧化峰电流与其浓度在1.0×10-6～1.0×10-4mol/L范围内呈良好的线性关系,线性相关系数为0.995。检出限为2×10-7mol/L。将该方法应用于模拟水样中间苯二酚的测定,回收率为96.5～104.2%。     

纳米NiO-还原石墨烯复合修饰玻碳电极的制备及电催化检测多巴胺

制备了纳米NiO-还原石墨烯复合修饰电极(NiO-rGO/GCE),并用于多巴胺(DA)的检测。用循环伏安法(CV)和差分脉冲伏安法(DPV)研究了DA在该修饰电极上的电化学行为。结果表明,在pH=7.0的磷酸盐缓冲溶液(PBS)中,该修饰电极对DA有良好的催化作用。DA浓度在5.0×10-7~3.2×10-5 mol/L范围内与氧化峰电流呈良好的线性关系,检出限为3.8×10-8 mol/L。用该修饰电极直接测定了血清中DA含量,回收率在97.8%~101.1%之间。     

免标型沙丁胺醇免疫电化学传感器

构建了以茜素为探针,二氧化钛掺杂乙炔黑和壳聚糖复合材料为信号放大平台的新型免标型沙丁胺醇免疫传感器。于修饰电极的表面电沉积金纳米粒子,实现沙丁胺醇抗体的固定并进一步增大电流响应。采用扫描电子显微镜(SEM)对材料进行表征,循环伏安法(CV)和电化学阻抗谱图(EIS)对修饰电极的构建过程及传感器的性能进行电化学表征。采用差分脉冲伏安法(DPV)检测茜素在修饰电极表面的峰电流值,不同浓度的沙丁胺醇(SAL)抗原与抗体发生免疫亲和反应后,该峰电流值随着沙丁胺醇浓度的增大而减小,并呈线性关系,据此建立峰电流值与沙丁胺醇浓度的关系并实现了对沙丁胺醇的定量检测。探究了缓冲溶液p H值、孵化温度和孵化时间对免疫传感器的影响。在最佳条件下,该免疫传感器对沙丁胺醇的线性响应范围为1.0~100μg/L,检出限(LOD)为0.67μg/L(3σ/k)。该免疫传感器具有良好的重现性、选择性和稳定性,已成功用于猪饲料和猪肉样品中沙丁胺醇的检测,加标回收率分别为100.2%~102.4%(相对标准偏差为1.9%~4.7%)和97.5%~103.3%(相对标准偏差为2.1%~3.5%)。     

MoS_2中空纳米球的制备及在超灵敏microRNA电化学生物传感器中的应用

采用模板法制备了二硫化钼中空球纳米材料,利用扫描电子电子显微镜、X射线衍射仪和Raman光谱仪对材料的形貌和结构进行表征.将适配体固定在金纳米粒子和二硫化钼共同修饰的电极上构建了一种新型的微小核糖核酸(microRNA)电化学生物传感器,采用循环伏安、微分脉冲伏安和电化学阻抗等技术对构筑的传感器进行表征.结果表明,microRNA浓度在1.0×10~(-10)~1.0×10~(-16)mol/L范围内峰电流(I)与microRNA浓度的负对数(-lgc)呈良好的线性,目标miRNA的检出限为0.55×10~(-16)mol/L.构建出的传感器具备选择性好、灵敏度高、稳定性强等特性,具有广阔的应用前景.     

纳米金/单壁碳管修饰玻碳电极对黄芩苷的电催化作用及快速检测

用循环伏安法(CV)在单壁碳纳米管表面直接沉积金纳米粒子,制备了纳米金/单壁碳纳米管修饰玻碳电极(NG/SWNT/GCE),并用扫描电镜(SEM)进行表征。研究了黄芩苷在该修饰电极上的电化学行为,结果表明该修饰电极对黄芩苷具有电催化作用。用示差脉冲伏安法(DPV)对黄芩苷进行测定,其氧化峰电流与黄芩苷浓度在2.0×10-8～7.0×10-6mol/L范围内呈线性关系。检出限为5.0×10-9mol/L(S/N=3)。该修饰电极实测了中药黄芩粉中黄芩苷的含量,回收率在96.8%～102.5%。     

Sensitive Electrochemical Detection of Bisphenol A Using Molybdenum Disulfide/Au Nanorod Composites Modified Glassy Carbon Electrode

Bisphenol A, an important compound that is classified as an environmental hormone, has been proven to have harmful effects on human health and ecology. A molybdenum disulfide/Au nanorod‐modified glassy carbon electrode was prepared as an electrochemical sensor for the detection of bisphenol A using a simple and convenient approach. UV–Vis spectrophotometry and transmission electron microscopy were employed to characterize the composite. The electrochemical behavior of bisphenol A at the modified electrode was investigated via differential pulse voltammetry and cyclic voltammetry. The results show that bisphenol A exhibits a good electrochemical signal at the modified electrode under optimized conditions, and a good linear relationship was observed between the bisphenol A concentration and peak current within the range of 0.01–50 μM, with a detection limit of 3.4 nM. Furthermore, the fabricated electrodes showed good anti‐interference, reproducibility and stability. The proposed electrochemical method was successfully applied for the detection of bisphenol A in milk and water samples, and its potential for applications in pollutant detection was demonstrated.     

槲皮素在聚谷氨酸修饰玻碳电极上的伏安行为及检测

制备了聚谷氨酸修饰玻碳电极,通过循环伏安法和差分脉冲伏安法研究了槲皮素在该修饰电极上的电化学行为。在pH 5.00的B-R缓冲液中,槲皮素在修饰电极上于0.28 V(vs Ag/AgCl)电位处产生一个灵敏的DPV阳极氧化峰,氧化峰电流与槲皮素的浓度在1.0×10-8～5×10-5 mol/L的范围内呈良好的线性关系,最低检测限为4.0×10-9 mol/L。实验表明,聚谷氨酸修饰电极可提高槲皮素的检测灵敏度,该电极用于芦丁水解产物中槲皮素的检测,回收率为103.4%～104.5%。     

硫酸特布他林在聚铬黑T修饰电极上的电化学行为及其测定

采用电化学聚合法制备了聚铬黑T膜修饰电极,应用扫描电镜、交流阻抗法和循环伏安法对修饰电极进行表征,以循环伏安法研究硫酸特布他林在修饰电极上的电化学行为,并以差示脉冲伏安法对其含量进行测定.该方法对硫酸特布他林有明显的电催化作用,在pH 7.0磷酸盐缓冲液中,氧化峰电流与硫酸特布他林浓度在1.2x10^-7~2.0x10^-6mol•L^-1范围内呈良好的线性关系,检测限为1.5x10^-8 mol•L^-1,回收率在97.9%～104.6%之间,RSD在2.8 % (C=8x10^-7mol•L^-1,n=11).该方法简便灵敏,结果准确可靠,方法重复性好,可用于硫酸特布他林及其片剂的质量控制.     

Polyfurfural-Electrochemically Reduced Graphene Oxide Modified Glassy Carbon Electrode for the Direct Determination of Nitrofurazone

An electrochemical sensor based on a polyfurfural-electrochemically reduced graphene oxide modified glassy carbon electrode has been developed for the sensitive and rapid determination of nitrofurazone. The morphologies and properties of the sensor were characterized by electrochemical impedance spectroscopy, scanning electron microscopy, cyclic voltammetry, and differential pulse voltammetry (DPV). In pH 7.0 Britton–Robinson buffer solution, the as-prepared polyfurfural-electrochemically reduced graphene oxide modified glassy carbon electrode shows excellent electrocatalytic performance for the electrochemical reduction of nitrofurazone, and the reduction peak current is about 9.45, 1.31, and 1.25 times higher than that of the bare glassy carbon electrode, polyfurfural modified glassy carbon electrode, and electrochemically reduced graphene oxide modified glassy carbon electrode, respectively. The DPV determination of nitrofurazone indicates that the linear range and detection limit of nitrofurazone are 1–50 and 0.25?µmol/dm³, respectively. In addition, this sensor exhibits high selectivity, reproducibility, stability, and also was successfully used to directly determine nitrofurazone in the commercial antibacterial lotion with comparative sensitivity to high-performance liquid chromatography, showing its promising application prospects.     

Mercury meniscus on solid silver amalgam electrode as a sensitive electrochemical sensor for tetrachlorvinphos

The in-house prepared mercury meniscus modified solid silver amalgam electrode (m-AgSAE) was successfully applied for the detection of organophosphate pesticide tetrachlorvinphos in pH 7 buffer solution. The electrochemical performance of m-AgSAE for the reduction of tetrachlorvinphos was evaluated using cyclic voltammetry (CV), differential pulse voltammetry (DPV), and square wave voltammetry (SWV), respectively. The surface morphology of solid silver electrode (AgE), as-amalgamated solid silver amalgam electrode (AgSAE), and polished solid silver amalgam electrode (p-AgSAE) was examined by field emission scanning electron microscopy (FESEM). Among the applied techniques, DPV and SWV analysis showed a remarkable increase in the reduction peak current and provided a simple, fast, and sensitive method for the determination of tetrachlorvinphos. The electrochemical impedance spectroscopy (EIS) was used to correlate the electrocatalytic activity of AgSAE, p-AgSAE and m-AgSAE with their interfacial charge transport capabilities. Under the optimized experimental conditions, the DPV and SWV responses were linear over the 1–9 μM and 10–50 μM concentration ranges with a detection limit of 0.06 μM for DPV and 0.04 for SWV. The estimation of tetrachlorvinphos in the ground and waste water samples with the proposed method was in good agreement with that of the added amount. The proposed electrochemical method not only extends the application of non-toxic m-AgSAE, but also offers new possibilities for fast and sensitive analysis of tetrachlorvinphos and its structural analogs in environmental samples.     

磁性石墨烯修饰辛基酚印迹传感器制备及应用研究

以辛基酚(4-OP)为模板分子,多巴胺为功能单体,采用电聚合技术在磁性石墨烯修饰碳电极表面制备对辛基酚具有高选择性与灵敏性的印迹电化学传感器。采用循环伏安法(CV)和差分脉冲伏安法(DPV)对此印迹传感器的电化学性能进行详细表征;采用扫描电子显微技术对修饰电极的形貌进行表征。结果表明,此印迹电化学传感器对辛基酚具有良好的特异识别性能。采用 DPV 法考察了孵化时间和洗脱溶剂对印迹传感器性能影响,结果表明,最佳孵化时间为14 min。此印迹电化学传感器的响应电流(△IR )与辛基酚在5.0×10-6~5.0×10-9 mol/ L 范围内浓度的负对数(-lgC)呈良好的线性关系,线性方程为△IR ( mA)=-0.25lgC(mol/ L)+2.35,检出限为3.64×10-10 mol/ L (S/ N=3)。此印迹电化学传感器对辛基酚具有良好的选择性和灵敏性,成功用于实际水样中辛基酚的检测,回收率为96.0%~104.0%。     

A Novel Electrochemical Sensor Based on Poly(1,5-diaminonaphthalene) and Poly(1,2-diaminoanthraquinone) Core-shell Composite Electrodes for Effective Voltammetric Determination of Nitrite

In this article, poly(1,2-diaminoanthraquinone) (pDAAQ) and poly(1,5-diaminonaphthalene) (pDAN) were electrochemically deposited layer by layer on a glassy carbon electrode (GCE) to generate pDAAQ/pDAN@GCE and pDAN/pDAAQ@GCE composite electrodes, respectively. The morphology and characteristics of the modified electrodes were investigated via electrochemical impedance spectroscopy)EIS), Fourier transform infrared spectroscopy (FT-IR), and scanning electron microscopy)SEM). The obtained results reveal the outstanding performance of the pDAN/pDAAQ@GCE electrode for electrochemical nitrite sensing where pDAAQ plays a vital role as the inner layer. Cyclic voltammetry (CV), linear sweep voltammetry (LSV), and differential pulse voltammetry (DPV) measurements revealed that the oxidation peak current of nitrite was proportional to its concentration. The best LSV results were obtained in a concentration range of 10–150 μM, with a limit of detection of 1.2 μM. Furthermore, the pDAN/pDAAQ@GCE composite electrode was used to determine nitrite ions in real water samples with good results.     

Zinc Oxide Nanoparticle‐modified Glassy Carbon Electrode as a Highly Sensitive Electrochemical Sensor for the Detection of Caffeine

Zinc oxide nanoparticles (ZnO NPs ) were prepared by a simple, convenient, and cost‐effective wet chemical method using the biopolymer starch. The prepared ZnO NPs were characterized by X‐ray diffraction (XRD ), scanning electron microscopy (SEM ), energy‐dispersive X‐ray (EDX ), Fourier transform infrared (FT‐IR ), and UV ‐visible spectroscopic techniques. The average crystallite size calculated from XRD data using the Debye–Scherer equation was found to be 15 nm. The electrochemical behavior of caffeine (CAF ) was studied using a glassy carbon electrode (GCE ) modified with zinc oxide nanoparticles by cyclic voltammetry (CV ) and differential pulse voltammetry (DPV ). Compared to unmodified GCE , ZnO NPs‐ modified GCE (ZnO NPs MGCE ) exhibited excellent electrocatalytic activity towards CAF oxidation, which was evident from the increase in the peak current and decrease in the peak potential. Electrochemical impedance study suggested that the charge‐transfer capacity of GCE was significantly enhanced by ZnO NPs . The linear response of the peak current on the concentrations of CAF was in the range 2–100 μM . The detection limit was found to be 0.038 μM. The proposed sensor was successfully employed for the determination of CAF in commercial beverage samples.     

基于石墨烯分子印迹电化学传感器测定芦丁

将石墨烯(GR)滴涂至裸Au电极表面,并以邻氨基酚为功能单体,芦丁为模板分子,制备了芦丁分子印迹膜电化学传感器,利用循环伏安法(CV)和差分脉冲伏安法(DPV)对制得的传感器进行了电化学性能研究,并且对制备条件和测定条件进行了优化。结果表明,与裸Au电极相比,该GR修饰的Au电极在[Fe(CN)_6]~(3-/4-)溶液中峰电流明显增大,显著提高了芦丁分子印迹传感器的灵敏度。在最优实验条件下,基于GR分子印迹电化学传感器在4.40×10~(-6)~2.80×10~(-4) mol/L范围内呈良好的线性关系,检测限为1.46×10~(-6) mol/L。用该传感器测定了黑茶中芦丁的含量,获得较好结果。     

Polystyrene sulphonate wrapped multiwalled carbon nanotubes modified graphite electrode for simultaneous determination of ascorbic acid, dopamine and uric acid

Graphite electrode is modified by casting multi-walled carbon nanotubes (MWCNTs) wrapped with polystyrene sulphonate (PSS) onto the surface of the bare graphite electrode. The modified electrode was characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The behavior of the modified electrode towards the oxidation of ascorbic acid (AA), dopamine (DA) and uric acid (UA) has been determined by cyclic voltammetry (CV), differential pulse voltammetry (DPV) and chronoamperometry (CA). The modified electrode showed better electrocatalytic activity towards AA, DA and UA compared to bare graphite electrode. The electrochemical oxidation signals of AA, DA and UA are well separated into three distinct peaks with peak potential difference of 222, 128 and 350 mV between AA-DA, DA-UA and AA-UA respectively in CV studies and corresponding peak potential separation in DPV are 228, 120 and 348 mV. This modified electrode was successfully used for simultaneous determination of AA, DA and UA in ternary mixture.