基于分子印迹电聚合膜的褪黑素传感器的研究

在弱酸条件下,以邻苯二胺为功能单体,褪黑素为模板,以电化学聚合物法在铂电极表面合成了性能稳定的褪黑素分子印迹聚合物膜.采用循环伏安法(CV)和差分脉冲法(DPV)对分子印迹传感器的识别性能进行了研究.结果表明:此传感器对褪黑素具有快的响应、良好的选择性和高的灵敏度.以K3Fe(CN)6为电子传递媒介,建立了一种差分脉冲伏安法(DPV)间接检测褪黑素的分析方法.在1×10-10～1×10-8 moL/L范围内,褪黑素的浓度与K3Fe(CN)6的相对峰电流变化呈良好的线性关系;检出限为1×10-11 mol/L(S/N=3).将此传感器应用于复合褪黑素及尿样中褪黑素含量的测定,加标平均回收率大于94％.     

灯盏乙素在石墨电极上的电化学行为研究

利用循环伏安法研究了灯盏乙素在石墨电极上的电化学行为及反应机理,结果表明灯盏乙素在石墨电极上有1对明显的准可逆氧化还原峰,电位分别为0.154 V和0.073 V。灯盏乙素在不同pH值下的伏安行为表明其在石墨电极上的氧化反应为2电子2质子的电化学过程。而灯盏乙素在不同扫速下的循环伏安行为表明其电化学氧化过程在低扫速下受吸附过程控制,而在高扫速下受扩散过程控制。在0.1 mol/L磷酸盐缓冲溶液(pH 7.0)中,采用差分脉冲伏安法对灯盏乙素含量进行测定,氧化峰电流与其浓度在5.0×10-7～5.0×10-5mol/L范围内呈线性关系,检出限(S/N=3)为1.5×10-7mol/L。用该方法对灯盏细辛中的灯盏乙素含量进行测定,回收率为98%,结果满意。     

流动注射化学发光法测定褪黑素

在强碱性介质中,铁氰化钾可直接氧化褪黑素产生化学发光。基于此,建立了一种测定褪黑素的流动注射化学发光分析方法。线性范围为1.9×10-6~2.3×10-4g/mL,检出限为5×10-7g/mL,该法已用于药物中褪黑素的测定。     

氨基硅油修饰碳糊电极阳极伏安法测定叶酸

在pH 6.8的B-R缓冲溶液中,采用氨基硅油修饰碳糊电极做工作电极,线性扫描伏安法对叶酸进行测定。伏安图上出现一灵敏的氧化峰,其峰电位EPa=+0.84 V,峰电流与叶酸的浓度在1.6×10-7~6.5×10-6mol.L-1范围内呈线性关系,检出限(3S/N)为7.2×10-8mol.L-1。富集时间为100 s,同时采用循环伏安法研究叶酸在氨基硅油修饰碳糊电极上的氧化还原反应,结果表明此电极反应为一不可逆的吸附过程。     

碳纤维微电极伏安法测定对乙酰氨基酚

采用碳纤维微电极对1.0×10-4 mol/L对乙酰氨基酚(ACOP)标准品(用pH=7.2的Tris-HCl稀释)采用差分脉冲法和循环伏安扫描法进行连续测定,考察了响应电流的变化.实验研究了缓冲溶液pH对ACOP氧化峰电流的影响以及ACOP氧化峰电流与扫速的关系.结果表明,用pH=10.0的Tris-HCl稀释溶液的测定结果稳定性最佳.ACOP的氧化峰电流与扫速的平方根成正比,其线性回归方程为:Ip(A)=5×10-10 V1/2(mV/s)+1×10-8,相关系数r=0.998 6,碳纤维微电极上的ACOP的氧化过程受扩散控制.采用差示脉冲伏安法对ACOP标准品氧化峰电流与浓度的关系进行定量分析,在1×10-7~1×10-4 mol/L浓度范围内,ACOP的氧化峰电流与其浓度呈现良好的线性关系,线性回归方程:Ip(A)=7×10-5 c(mol/L)+5×10-11,线性相关系数r=0.999 0.该法可用于ACOP样品的分析测定,结果令人满意.     

单壁碳纳米管-氧化石墨烯复合修饰电极测定邻苯二酚

制备了用于测定邻苯二酚的单壁碳纳米管-氧化石墨烯复合修饰玻碳电极.用循环伏安法研究了邻苯二酚在该电极上的电化学行为.结果表明,该修饰电极对邻苯二酚具有良好的电催化性能.在最佳实验条件下,采用差分脉冲伏安法对邻苯二酚进行了测定,其氧化峰电流与邻苯二酚浓度在2×10~(-6)~1×10~(-4) mol/L范围内呈线性关系,相关系数为0.996 2,检出限为4×10~(-7) mol/L.该电极具有良好的重现性,用于模拟废水中邻苯二酚的测定结果令人满意.     

OAP-H~2O~2-HRP伏安酶联免疫分析新体系测定人血清铁蛋白

首次提出邻氨基酚(OAP)-H~2O~2-辣根过氧化物酶(HRP)伏安酶联免疫分析新体系并用于人血清中铁蛋白的测定.本方法以线性扫描二阶导数伏安法栓测HRP催化H~2O~2氧化OAP的产物,用于游离HRP和各种HRP标记物的测定,灵敏度均高于经典的ELISA显色光度法.测定游HPR的线性范围为1.0x10^-^1^2-4.0x10^-^9g/mL,检测限达6.0x10^-^1^3g/mL.本法对铁蛋白测定的线性范围为0.2-320ng/mL,用所建立的方法对人血清样品进行了测定,并与现行的ELISA显色光度法进行对照,二者相关性很好.对此伏安酶联免疫分析新体系的电极还原过程也进行了详细的研究.     

酸性大红3R的电化学研究及应用

采用循环伏安法和方波伏安法考察了酸性大红3R在碳糊电极上的伏安行为和反应机理。当扫描速率为0.1 V/s时,在pH 1的0.05 mol/L H2SO4支持电解液中,酸性大红3R有一对峰电位分别是0.74 V和0.72 V（vs.饱和甘汞电极）的氧化峰和还原峰,并且显示吸附控制的2电子单质子的准可逆氧化还原过程。在最佳实验条件下,酸性大红3R的方波氧化峰峰电流与其浓度在2.12×10^-5-3.39×10^-4mol/L范围内呈线性关系,检出限为8.35×10^-6mol/L,由此建立测定酸性大红3R含量的方波伏安法。该方法可用于计算酸性大红3R常规染羊毛与蚕丝的上染率,测定结果与分光光度法一致。     

电化学方法对农药啶虫脒的间接测定

啶虫脒本身不具有电化学性质,而其在NaOH溶液中的水解产物为电活性物质。采用循环伏安法(CV)、示差脉冲伏安法(DPV)研究了啶虫脒水解产物在碳糊电极上的电化学行为,并初步探讨了其反应机理。在pH9.0的磷酸盐缓冲液(PBS)中,啶虫脒水解产物在约0.9 V(vs.SCE)产生一灵敏的氧化峰,表明电极反应是受扩散控制的不可逆氧化过程。基于啶虫脒水解产物的氧化行为,以0.9 V为工作电位,采用计时安培法进行测定,其响应电流与啶虫脒的浓度在2.0×10-7~2.8×10-5mol/L范围内呈良好的线性关系,方法的检出限为1.0×10-7mol/L。该方法成本低、操作方便、重复性好,对人体与环境无毒害,将其用于啶虫脒实际样品的测定,结果满意。     

掺杂硒修饰碳糊电极伏安法测定对乙酰氨基酚

采用循环伏安法制备了掺杂硒修饰碳糊电极,用循环伏安法和差分脉冲伏安法研究了对乙酰氨基酚在掺杂硒修饰碳糊电极上的电化学行为,建立了掺杂硒修饰碳糊电极测定对乙酰氨基酚的电化学方法。在pH 4.6的0.1mol·L-1乙酸-乙酸钠缓冲溶液中,对乙酰氨基酚在+0.61V呈现一个灵敏的氧化峰。对乙酰氨基酚的浓度在6.0×10-7~1.5×10-4 mol·L-1范围内与其氧化峰电流呈线性关系,检出限(3s/k)为2.8×10-7 mol·L-1。方法用于药品中对乙酰氨基酚的测定,测定结果与药典法测定值相符,测定值的相对标准偏差(n=5)在2.1%~2.5%之间。     

Electrocatalytic Properties and Voltammetric Determination of Melatonin at a Nanostructured Film Electrode

A multi-wall carbon nanotube (MWNT) film coated glassy carbon electrode (GCE) was fabricated, and the electrochemical behavior of melatonin on the MWNT film coated GCE was investigated. The oxidation peak current of melatonin increases significantly and the oxidation peak position shifts positively at the MWNT film modified GCE compared to that at a bare GCE. This indicates that MWNTs feature highly effective catalysis to the electrochemical oxidation of melatonin. A simple and sensitive electroanalytical method was developed for the determination of melatonin. The oxidation peak current is proportional to the concentration of melatonin from 8×10^–8 to 1×10^–5molL^–1. The detection limit is about 2×10^–8molL^–1 for 3min accumulation. The proposed method was demonstrated to work satisfactorily with commercial capsules.     

End-column amperometric detection of melatonin by high performance capillary electrophoresis

A rapid and sensitive method is described for the detection of melatonin in rat pineal gland and melatonin tablets. Capillary electrophoresis (CE) with electrochemical detection (EC) was used. This method had high sensitivity and good reproducibility. The detection limit of melatonin was as low as 1.3x10(-9) mol/l (0.30 fg). There was a linear range of concentration from 3.9x10(-7) to 3.25x10(-5) mol/l with a correlation coefficient of 0.999. The linear equation was Y=8.27+0.0042X with a slope of 0.0042 pA/nM. The relative standard deviations of the peak current response and the migration time for 16 continuous injections of 6.5 muM melatonin were 4.5 and 0.48%, respectively. The proposed method was applied to detect melatonin in the rat pineal gland and the melatonin tablets. Good results were obtained compared with previous reports.     

Oxidation of melatonin on a glassy carbon electrode modified with metallic glucosamines. Synthesis and characterization

In this study, a glassy carbon electrode modified with different cobalt glucosamines (CoGlu-R), iron glucosamines (FeGlu-R), and nickel glucosamines (NiGlu-R) was used for the electroanalytical determination of melatonin in buffer solutions at pH 7.3 using cyclic and square wave voltammetry. The complexes were synthesized and characterized by IR-TF, ¹H-NMR, and UV–visible spectroscopy. When comparing glucosamines of different metals, the influence of the nature of the metal on the activity is not very strong. The most active complex was CoGlu-R. The oxidation peak was used to determine melatonin in the concentration range of 10^?8–10^?5 M with a detection limit of 2.15?×?10^?7 M (LOD). Our results indicate that the current peak is under mass-transport control and probably suggest that chemical reactions coupled with electrochemical steps are involved. The melatonin oxidation current with this kind of modified electrodes is small but this modified electrode shows high selectivity in medium-199 (glutamine, phenol red, glucose, Na⁺, CO₃ ^2?) with human placental tissue; trophoblast and endothelial cells (K⁺, Ca²⁺, traces of Cu²⁺ and Mg²⁺), yet the tryptophan causes interference.     

Analysis of the antioxidant activity of an indole library: cyclic voltammetry versus ROS scavenging activity

The electrochemical behavior of an indole library of compounds, including several tryptophan and tryptamine derivatives previously demonstrated to be active against several reactive oxygen species (ROS), was investigated. For this purpose, a voltammetry study was undertaken and the oxidation potential was correlated to the scavenging activity reported for the studied indoles. All the compounds showed an oxidation potential peak lower than that observed for indole (Epox = 1.035 V), but higher than that described for the antioxidant melatonin (Epox = 0.715 V). The electrochemical behavior showed a high correlation with the scavenging activity of peroxyl radical, for selected compounds.     

Sensitive Adsorptive Stripping Voltammetric Methodologies for the Determination of Melatonin in Biological Fluids

The reversible redox process that melatonin presented on carbon paste electrodes was the basis of a sensitive methodology for the determination of this hormone. From all the processes presented by this hormone, this was never used before as the basis of voltammetric measurements for melatonin determination. Therefore, parameters that affected the cyclic voltammetric signal were studied. A limit of detection as low as 9×10^?11 M was obtained when optimized alternating current voltammetry was employed. The reproducibility was excellent due to an adequate pretreatment of the solid electrode (RSD=2.7%, n=10). A comparison with methodologies that employ different electrochemical techniques from the point of view of their analytical characteristics was made. This methodology has proved to be suitable for the determination of melatonin in biological fluids.     

Study on the Electrochemical Behavior of Melatonin with an Activated Electrode

It was found that melatonin could be incorporated and accumulated on the surface of the glassy carbon electrode which was activated electrochemically by pretreatment in sodium hydroxide solution by means of cycling the potential well into the positive limit of the solvent. In Britton‐Robinson buffer solution (pH 6.7), melatonin gave a sensitive oxidation wave at a potential of +0.65 V (vs.Ag/AgCl) by using Osteryoung square‐wave stripping voltammetry (OSWSV). The oxidation process has been shown to be irreversible and adsorption‐controlled at this electrode by means of cyclic voltammetry and linear sweep voltammetry. A chronocoulometric characterization of the adsorption characteristics of melatonin at this electrode is also presented. The factors affecting the peak current were optimized, and the dependence of peak currents on the concentration of melatonin was found to be linear in the range 8.0×10^?7?1.0×10^?5 mol L^?1. A detection limit of 5.0×10^?8 mol L^?1 was obtained (signal‐to‐noise ratio of 3). This method was applied to the assay of melatonin in tablets and capsules with good recoveries (98–100%).     

双酚A在SDS现场自组装膜与[bupy]PF6复合修饰碳糊电极上的电催化氧化及电分析方法

研究了双酚A(BPA)在十二烷基硫酸钠(SDS)现场自组装膜与离子液体N-丁基吡啶夫氟磷酸盐([ bupy]PF6)复合修饰碳糊电极(SDS-[ bupy]PF6/CPE)上的电催化氧化行为和电化学动力学性质.实验结果表明,在SDS-[ bupy]PF6/CPE上BPA发生了一受扩散控制的不可逆电化学氧化过程,用循环伏安(CV)法和计时电流(CA)法测得BPA在SDS-[bupy]PF6/CPE上的电极反应过程动力学参数.用方波伏安(SWV)法测得BPA氧化峰电流(Ipa)与其浓度在1.0×10-5～ 1.0×10-3 mol/L范围内呈良好的线性关系,线性方程为Ipa(μA) =2.635 +51.30c( 10-3 mol/L),r =0.998 1,检测限(S/N=3)为3.01×10-7 mol/L,同时运用SWV法对湖水样品中双酚A的含量进行了电化学定量测定.     

A Simple Method for Melatonin Determination in the Presence of High Levels of Tryptophan using an Unmodified Carbon Paste Electrode and Square Wave Anodic Stripping Voltammetry

Electrochemical determination of melatonin in the presence of tryptophan is a challenge because of the coincidence of voltammetric signals of these compounds when executing a voltammetric technique. The new method for selective determination of melatonin based on the square wave anodic stripping voltammetry determination of an electroactive product of melatonin was suggested here. This product is produced by previously applied positive pre-potential to a carbon paste electrode, immersed in the test solution. By this means, the electrochemical signal of melatonin was separated effectively from that of tryptophan, making it possible to determine melatonin in the presence of a high concentration of tryptophan. The effect of important parameters on electrode performance was studied and optimized. The optimum response was obtained at pH=2 and utilizing the pre-potential magnitude of +0.8 V, applied for 10 s. A linear relationship was found between peak current intensity and melatonin concentrations over the range of 5.00×10⁻⁷ to 8.00×10⁻⁵ mol L⁻¹. A detection limit of 8.30×10⁻⁸ mol L⁻¹ was calculated for the method (S/N=3). The selectivity of the method was considerably high, because of the independence of melatonin signal to the presence of higher amounts of some potentially interfering agents such as ascorbic acid, tryptophane glucose, etc. As an analytical application, the proposed sensor was used for the determination of melatonin in pharmaceutical and food samples.     

Electrocatalytic oxidation of sulfite by acetylferrocene at glassy carbon electrode

The electrochemical oxidation of sulfite catalyzed by acetylferrocene (AFc) at a glassy carbon electrode (GCE) in 0.2 M NaClO₄ aqueous solution has been studied by cyclic voltammetry. Although sulfite itself showed a sluggish electrochemical response at the GCE, the response could be enhanced greatly by using AFc as a mediator, which enables a sensitive determination of the substrate (sulfite). The reaction rate constant for catalytic oxidation was evaluated as (7.02 ± 0.05) × 10⁴ M ^?1 s^?1 by chronoamperometry. Experimental conditions that maximize the current efficiency of the electrocatalytic oxidation, such as the pH and both the catalyst (AFc) and substrate (sulfite) concentrations, were also investigated. The electrochemical kinetics of electrocatalytic oxidation of sulfite by AFc has been studied by cyclic voltammetry. In the presence of 5 × 10^?4 M AFc, the oxidation current is proportional to the sulfite concentration and the calibration plot was linear over the concentration range 2 × 10^?4–2.4 × 10^?3 M . This result can be applied in the determination of real samples. Copyright © 2005 John Wiley & Sons, Ltd.