改性HZSM-5催化乙醇脱水制乙烯的研究

采用离子交换法分别制备了铁、钴、镍改性的HZSM-5分子筛催化剂.在连续流动固定床微型反应装置上对催化剂进行了活性评价,结果表明镍改性的催化剂具有较好的低温活性.采用透射电镜(TEM),X射线衍射(XRD),吡啶程序升温脱附(Py-TPD),N2-吸附脱附和程序升温氧化(TPO)等手段对催化剂反应前后的物性进行了表征,结果表明催化剂的表面酸性决定其催化乙醇脱水的性能.镍改性后,降低了催化剂的强酸量、增加了弱酸量,有利于乙醇转化率和乙烯选择性的提高,镍是比较合适的改性金属.以镍改性的HZSM-5为催化剂,对乙醇脱水制乙烯反应的工艺条件进行了优化.     

酸化膨润土负载金催化剂用于CO氧化

用盐酸和硫酸对膨润土（Ben）进行改性处理,采用浸渍法（IMP）、沉积-沉淀法（DP）和阳离子吸附法(CA)制备改性膨润土负载的金催化剂,以CO氧化作为探针反应对催化剂的催化性能进行了研究,采用BET、XRD、TEM和TPD等对催化剂进行表征。 结果表明,经过简单的酸处理后的膨润土比表面积和孔体积有了大幅度的提高,硫酸酸化的膨润土作为载体较之盐酸酸化土更容易得到活性较高的金催化剂,XRD粒径计算结果和TEM观察结果证明,硫酸酸化的膨润土作为载体相比盐酸酸化土可以得到Au颗粒度更小的催化剂。 不同制备方法中,阳离子吸附法能较好的将Au负载于膨润土载体上,得到小颗粒的金催化剂,且在吸附48 h、450 ℃焙烧、150 ℃下H2还原的预处理条件下得到的催化剂活性最好。     

Ni/MWCNT及镧改性Ni/MWCNT催化CO2甲烷化反应的性能

以多壁碳纳米管(MWCNT)为载体, 通过浸渍法制备了负载型镍催化剂和稀土镧改性的镍催化剂, 并对其二氧化碳甲烷化的催化性能进行了研究. 借助比表面积测试、程序升温还原(TPR)、X射线衍射(XRD)和X射线光电子能谱(XPS)等表征手段研究了稀土镧的添加对Ni/MWCNT催化剂结构和表面组成、催化剂还原性能以及CO₂甲烷化反应性能的影响. 结果表明: 稀土镧改性的Ni/MWCNT较Ni/MWCNT催化剂具有更好的CO₂甲烷化活性, 镧组分的加入提高了催化剂表面的镍物种浓度和分散度, 弱化了氧化镍与载体MWCNT之间的相互作用, 促进了氧化镍的还原, 同时提高了表面镍物种的电子密度, 增加了对反应物的吸附能力, 从而提高了其CO₂甲烷化活性. 制备过程中稀土镧的添加次序对催化性能有较明显的影响, 其活性顺序为先浸渍镧后浸渍镍制备的催化剂活性明显好于先浸渍镍后浸渍镧制备的催化剂.     

多级孔HZSM-5分子筛催化剂的制备及低碳烃芳构化应用

采用0.2 mol/L的NaOH溶液对HZSM-5分子筛进行了不同时间的碱改性处理, 并对分子筛的结构和酸性进行表征, 考察了碱改性对HZSM-5催化剂的低碳烃芳构化活性的影响. 结果表明, HZSM-5分子筛经碱改性后会产生少量介孔, 且随改性时间延长, 介孔数量增加, 平均孔径增大, 总酸量降低, B酸/L酸比值降低. 120 min碱改性HZSM-5催化剂的活性、 稳定性以及目标产物苯、 甲苯、 乙苯和二甲苯(统称BTEX)的选择性最高.     

助剂铬对Ni/MgO催化剂CVD法制备碳纳米管的促进作用

采用溶胶-凝胶法制备了助剂Cr改性的Ni/MgO催化剂, 用化学气相沉积(CVD)法在600 ℃下裂解甲烷生长碳纳米管, 研究了助剂Cr的引入对催化剂微结构和制备碳纳米管性能的影响. 催化剂样品用XRD, TPR和CO-TPD进行了分析, 制备的碳纳米管用TEM和XRD进行了表征. 实验结果表明, NiO和MgO之间存在着强相互作用而形成固溶体, Ni/MgO催化剂经氢气处理后其中的镍氧化物只有极少部分被还原成为镍. 助剂铬的引入明显促进了镍的还原, 使得催化剂表面的Ni活性中心数增多, 从而使催化剂的活性和性能得到了明显的改进. 在加入助剂后碳纳米管的产率明显增加, 当Cr质量分数为8%时, 碳纳米管的产量为未加助剂时产量的5倍, 碳纳米管和催化剂的质量比达到1928. 当Cr含量进一步增加时, Ni在催剂表面聚集形成大颗粒, 制备出的产品中含有大量的碳纳米纤维和无定形碳. 以8%Cr-Ni/MgO催化剂合成的碳纳米管具有比较高的产率且质量较好.     

CaO改性对CuZnAlZr催化剂在合成气制低碳醇中性能的影响

采用机械混合法和共沉淀法制备了CaO改性CuZnAlZr氧化物催化剂,在高压微型固定床反应器上考察了其在合成气制低碳醇反应中的催化性能,利用粉末X射线衍射(XRD)、低温氮气吸附-脱附、H2程序升温还原(H2-TPR)和二氧化碳吸附-脱附(CO2-TPD)等技术对催化剂进行了表征.结果显示:CaO改性对CuZnAlZr催化剂的织构性质没有明显的影响;但共沉淀法制备的CaO改性CuZnAlZr催化剂具有弱碱性和中等强度两种碱性中心,且有较多的碱中心数量;而未改性的CuZnAlZr催化剂只具有弱碱性中心.CO加氢反应结果表明:经共沉淀法制备的CaO改性CuZnAlZr催化剂对C2+醇的生成有明显的促进作用.     

Alkali-resistant performance of V2O5-MoO3/TiO2 catalyst modified by SiO2

以陶瓷为骨架,用溶胶凝胶法和浸渍法制备了V2O5-MoO3/TiO2催化剂,并用SiO2进行改性.采用浸渍法模拟碱K中毒,研究了SiO2改性前后催化剂中毒脱硝效率的变化,并通过BET、H2-TPR、NH3-TPD等技术手段对催化剂进行了表征.结果表明,加入SiO2后,催化剂的比表面积明显提高.SiO2改性后新鲜催化剂还原温度向低温方向迁移10℃左右,氧化还原能力得到了提高,其表面酸强度和酸量也得到较大的提高.反应评价结果表明,SiO2改性可以提高催化剂抗碱中毒的件能.     

GMMT复合材料的制备及吸附性能研究

采用直接插层法对钠基膨润土进行改性,制备了明胶/膨润土(简称GMMT)复合材料;研究了明胶插层复合改性膨润土的工艺条件;通过测定明胶插层复合前后膨润土的比表面积等的变化,探讨了GMMT复合材料的吸附性能.     

脂肪酸加氢改性Ni及Ni-Pd催化剂的制备

工业动植物油脚的主要成分为不饱和脂肪酸,通过催化加氢制得的硬脂酸[1,2],可作橡胶添加剂。但不饱和脂肪酸的酸值较高,易使镍催化剂皂化中毒而失活。本文在镍催化剂的基础上,加入微量的过渡或碱士等活泼金属作助剂,提高催化剂的抗皂化性能;加入微量钯,提高催化剂的活性,采用沉淀法,以硅藻土为载体,制备了负载型改性Ni及Ni Pd催化剂。并与国内化工企业常用的棕榈酸(酸值为188 6mgKOH/g)进口加氢催化剂USA 140和USA 110在相同条件下对进行对比。1　实验部分1 1　催化剂制备将18gNi(NO3)2:6H2O溶于130ml水,再依次加入一定配比的过…     

酸化膨润土催化合成乙基叔丁基醚的研究

以不同浓度的H2SO4对膨润土进行改性,得到酸化膨润土催化剂x%H2SO4-BN(x=20,25,30,35,40),通过XRD,BET,FT-IR,Py-IR和NH3-TPD对膨润土的结构和性质进行表征,证明膨润土经酸化后,骨架结构基本没有变化,但是其比表面和孔容有很大的提高,且弱酸位增多.将其用于催化乙醇(EtOH)和叔丁醇(TBA)合成乙基叔丁基醚(ETBE)的醚化反应.结果表明,30%H2SO4-BN催化活性最好,最佳实验条件:催化剂用量为3.5%(催化剂与叔丁醇的质量百分比),反应温度130℃,原料摩尔比(EtOH:TBA)为2∶1.     

Thermodynamic and Kinetic Studies for the Adsorption of Fe(III) and Ni(II) Ions From Aqueous Solution Using Natural Bentonite

In this study, the adsorption behavior of natural bentonite with respect to Fe(III) and Ni(II) has been studied in order to consider its application to purity metal finishing wastewaters. During the adsorption process, batch technique is used, and the effects of pH, bentoite amount, temperature, heavy metal concentration, bentonite treatment (calcinations of natural bentonite at 700°C, washing by deionized water to remove the excess salt from bentonite surface), and agitation time on adsorption efficiency are studied. The washed and calcined bentonite samples were labeled by WB and CB, respectively. The pH-dependence of Fe(III) and Ni(II) sorption on the bentonite is significantly more noticeable, indicating a major contribution of surface complexation at the edge sites. It was determined that adsorption of Fe(III) and Ni(II) is well fitted by the second order reaction kinetic. Furthermore, the sorption rate of Fe(III) was higher than the sorption rate of Ni(II). Adsorption of Fe(III) and Ni(II) on NB appeared to follow Langmuir isotherm. In addition, calculated and experimental adsorbed amounts of Fe(III) by the unit NB mass are very higher than Ni(II). The paper also discusses the thermodynamic parameters of the adsorption (the Gibbs free energy, entropy, and enthalpy). Our results demonstrate that the adsorption process was spontaneous and endothermic under natural conditions. Also the adsorption capacity of bentonite for Fe(III) Ni(II) and increases with increased bentonite dose. According to the equilibrium studies, the selectivity sequence can be given as Fe(III) > Ni(II). The adsorbed amount of Fe(III) and Ni(II) on washed bentonite (WB) were very higher compared to NB and CB. Our results show that bentonite could especially WB be considered as a potential adsorbent for Fe(III) and Ni(II) removal from aqueous solutions.     

Study of <Superscript>63</Superscript>Ni(II) sorption on CMC-bound bentonite from aqueous solutions

Bentonite was investigated to remove Ni(II) from aqueous solutions because of its strong sorption ability. Herein, bentonite was modified with sodium carboxymethylcellulose (CMC) and used as an adsorbent to remove Ni(II) from aqueous solutions. The results indicated that CMC-bentonite had higher sorption capacity than bare bentonite in the sorption of Ni(II) from aqueous solutions. Sorption of Ni(II) on CMC-bentonite was mainly dominated by ion exchange or outer-sphere surface complexation at low pH values, but by inner-sphere surface complexation or surface precipitation at high pH values. The thermodynamic data calculated from temperature dependent sorption isotherms indicated that the sorption of Ni(II) to CMC-bentonite hybrids was an spontaneous process and enhanced with increasing temperature.     

Thermodynamics of Pb2+ and Ni2+ adsorption onto natural bentonite from aqueous solutions

Removal of Pb2+ and Ni2+ from aqueous solutions by sorption onto natural bentonite was investigated. Experiments were carried out as a function of particle size, the amount of bentonite, pH, concentration of metals, contact time, and temperature. The adsorption patterns of metal ions onto followed the Langmuir, Freundlich, and Dubinin-Radushkevich isotherms. This included adsorption isotherms of single-metal solutions at 303 K by batch experiments. The thermodynamic parameters (DeltaH,DeltaS,DeltaG) for Pb2+ and Ni2+ sorption onto bentonite were also determined from the temperature dependence. The adsorptions were endothermic reactions. The results suggested that natural bentonite is suitable as a sorbent material for recovery and adsorption of metal ions from aqueous solutions.     

Impact of environmental conditions on the removal of Ni(II) from aqueous solution to bentonite/iron oxide magnetic composites

The sorption of radionuclide ⁶³Ni(II) on bentonite/iron oxide magnetic composites was investigated by batch technique under ambient conditions. The effect of contact time, solid content, pH, coexistent electrolyte ions, fulvic acid, and temperature on Ni(II) sorption to bentonite/iron oxide magnetic composites was examined. The results demonstrated that the sorption of Ni(II) was strongly dependent on pH and ionic strength at pH <8.0, and was independent of pH and ionic strength at high pH values. The sorption of Ni(II) was dominated by outer-sphere surface complexation or ion exchange at low pH, whereas inner-sphere surface complexation was the main sorption mechanism at high pH. The experimental data were well fitted by Langmuir model. The thermodynamic parameters (∆G°, ∆S°, ∆H°) calculated from the temperature-dependent sorption isotherms indicated that the sorption of Ni(II) on bentonite/iron oxide magnetic composites was an endothermic and spontaneous processes. The results show that bentonite/iron oxide magnetic composites are promising magnetic materials for the preconcentration and separation of radionickel from aqueous solutions in environmental pollution.     

菲加氢裂解制BTX的催化剂研究

采用等体积浸渍法制备了Ni/ZSM-5、Ni/HY、Ni/Al₂O₃和Ni/USY四个系列Ni含量不同的催化剂,在固定床反应器中考察了四类催化剂对菲的加氢裂化制BTX反应的催化性能。借助BET、SEM、热重和差热分析对催化剂的形貌、比表面积、平均孔径及积炭情况进行了表征,结合其结果对催化剂性能进行了分析。结果表明,Ni/HY和Ni/USY催化剂中Ni含量为12%时性能最优,收率可达52%。Al₂O₃催化剂的最佳Ni含量为6%,该系催化剂初始性能尚可,但失活较快;ZSM-5型分子筛催化剂性能较差。     

Modeling of radionickel sorption on MX-80 bentonite as a function of pH and ionic strength

MX-80 bentonite was detected using acid-based titration, XRD and FTIR in detail. The sorption behavior of 63Ni(Ⅱ) from aqueous solution to MX-80 bentonite was investigated as a function of solid content, ionic strength and pH by using batch technique. The experimental data of 63Ni(Ⅱ) sorption on MX-80 bentonite was obtained using the diffuse layer model (DLM) with the aid of FITEQL 3.1 program. The results indicated that the sorption of 63Ni(Ⅱ) on MX-80 bentonite was mainly dominated by surface complexation...     

氟离子对TiO2/膨润土光催化降解酸性桃红的影响

研究了在紫外光照射下, 添加氟离子对P25(锐钛矿)和TiO2/膨润土光催化降解酸性桃红(SRB)的影响. 紫外可见光谱测定结果表明无氟的反应体系, pH值越小, 光降解速率越快; pH值固定, 添加氟离子越多, 反应速率越快, 在TiO2/膨润土催化剂上, 当氟离子浓度达到一定程度时, 反应速率不再变化. 在P25和TiO2/膨润土催化剂上, 添加氟离子对H2O2的产生量影响不同, 通过电子顺磁共振(EPR)技术探测到了超氧自由基和羟基自由基, 这两个体系添加氟离子对其产生强度影响不同, 这可能是因为TiO2/膨润土催化剂为层状结构, BET 比表面积较大, 经XRD和TEM测试表明其晶粒直径约为57.9 nm. TiO2/膨润土催化剂连续循环使用11次, 光催化活性基本不变, 这个现象说明TiO2/膨润土催化剂既易于从分散体系中分离出来, 而且其稳定性也好, 它是一个有应用前途的催化剂.     

Chemical Modification of Upgraded Bentonite as Filler of Natural Rubber/Organobentonite Composite

Bentonite is an abundant natural resource that has great prospects for used as filler in natural rubber industry after certain modification, either through physical or chemical process. Reduction of mineral impurities in the bentonite was done to form upgraded bentonite by using hydrocyclone, and chemical modification of upgraded bentonite to form organobentonite was done by addition of commercially surfactant. Natural rubber/organobentonite composites made by melting compound technique at roll mill. The results showed that the reduction process of mineral impurities in the bentonite had been able to reduce the content of impurities, such as Fe₂O₃, CaO, and K₂O. Meanwhile, by using XRD dan FTIR analysis, an increase in the dose of surfactant on upgraded bentonite might increase the organic content and basal spacing of organobentonite. Low mineral impurities organobentonite was capable of producing natural rubber/organobentonite composite with faster vulcanization time and some better mechanical properties (such as elongation at break and modulus 100%) than natural rubber/carbon black composite.     

Thermodynamic studies of Ni(II) adsorption onto bentonite from aqueous solution

The adsorption behavior of Ni(II) onto bentonite was studied as a function of temperature under optimized conditions of shaking time, amount of adsorbent, pH, and concentration of the adsorbate. Thermodynamic parameters such as ΔH^°, ΔS^°, and ΔG^° were calculated from the slope and intercept of the linear plot of lgK_D against 1/T. Analysis of adsorption results obtained at T=(298, 303, 313, and 323) K showed that the adsorption pattern on bentonite followed the Langmuir, Freundlich, and D-R isotherms. A flame atomic absorption spectrophotometer was used for measuring the concentration of Ni(II).