Solvent and kinetic penultimate unit effects in the copolymerization of acrylonitrile with itaconic acid

Copolymerization of acrylonitrile (AN) with itaconic acid (IA) in dimethylformamide (DMF) and DMF/water mixture was investigated at enhanced concentrations of the latter. Analysis of the copolymer composition revealed the existence of a marked penultimate unit effect with respect to radicals terminated in AN. The reactivity of IA was considerably less than that of AN, manifested as a negative reactivity ratio for the former. The r_IA values ranging from −0.28 to −0.50 and r_AN values ranging from 0.53 to 0.70, were obtained by Kelen-Tudo's (KT) and extended KT methods. The penultimate reactivity ratios were determined by both linear and non-linear methods. The values ranged from r₁=0.009 to 0.01, r₁^′=0.0015 to 0.0043, r₂=0.54 to 0.69 and r₂^′=0.9 to 1.03. The reactivity of AN radical towards IA decreased about twofold when the latter formed the penultimate group. The penultimate model explained an acceptable rational feed-copolymer composition profile for the whole composition range. Addition of water decreased the reactivity of IA slightly. IA caused a decrease in the apparent copolymerization rate in agreement with the observed trends in the reactivity ratios; presence of water caused a further decrease in the rate of polymerization. A statistical prediction of monomer sequences based on reactivity ratios implied that IA existed as a lone monomer unit between the long sequences of AN units.     

碳酸乙烯酯溶剂中丙烯腈的聚合行为

以碳酸乙烯酯为溶剂,偶氮二异丁腈（AIBN）为引发剂,采用溶液自由基聚合的方法对丙烯腈(AN)均聚合、丙烯腈/衣康酸(AN/IA)二元共聚及丙烯腈/衣康酸/丙烯酸甲酯(AN/IA/MA)三元共聚合进行了研究。 考察了反应温度对丙烯腈均聚合,以及聚合单体浓度对丙烯腈共聚合的影响,在60 ℃合成了相对分子质量高于4.5×105、单体转化率高于85%的丙烯腈均聚物及共聚物。 采用正十二烷基硫醇（DDT）和甲酰基哌啶（FP）作为链转移剂,对AN均聚物、AN/IA及AN/IA/MA共聚物的相对分子质量进行调控,考察了链转移剂浓度对聚合物相对分子质量和单体转化率的影响。 结果表明,w(DDT)为0.25%时（以单体质量计）,聚合物相对分子质量可有效调节到1×105,而单体转化率保持在80%以上。     

Photo and thermal polymerizations sensitized by donor–acceptor interaction. II. Photopolymerization and electronic spectroscopy of the isobutyl vinyl ether–acrylonitrile system

Photopolymerization of acrylonitrile (AN), an acceptor monomer, was found to be accelerated in the presence of isobutyl vinyl ether (IBVE), a donor monomer. The propagation is completed by a radical mechanism as judged by copolymer compositions; in contrast to the N-vinylcarbazole–AN system studied previously. This photopolymerization system is entirely stable if kept in the dark. The comparison of the relation between R_p and [IBVE]/[AN] ratio in the monomer feed found for the spontaneous photopolymerization with that for radical polymerization initiated by azobisisobutylonitrile in the dark leads to the conclusion that the rate of photoinitiation is enhanced by the interaction between AN and IBVE, whereas the propagation step by a radical mechanism is retarded by increasing concentration of IBVE. The contact charge-transfer complex between IBVE and AN was confirmed by electronic spectroscopy of the polymerization system, which showed photosensitization by charge-transfer interaction. The spectroscopic study of other weak donor–weak acceptor systems is also discussed.     

Radical polymerization of styrene initiated by styrene–arsenic sulfide complex

Styrene forms a complex with arsenic sulfide which in DMF at 85°C initiates radical polymerization yielding high molecular weight polymer. The order of reaction, with respect to initiator and monomer, is 0.5 ± 0.02 and unity, respectively. The energy of activation for the system computed as 96 kJ mol^?1 and the polymerization is retarded by hydroquinone. A possible mechanism for reaction has also been proposed.     

Kinetic study of radical polymerization of acrylonitrile in the presence of triphenyl phosphite

In the presence of triphenyl phosphite (TPP), the radical polymerization of acrylonitrile (AN) with α,α′-azobisisobutyronitrile (AIBN) as the initiator was carried out at 50°C, and the effects of TPP on the polymerization were kinetically investigated. The rate of polymerization was found to be proportional to the first order of the AIBN concentration and the AN concentration, respectively, at all concentrations of TPP. However, the rate of polymerization was proportional to the reciprocal of the TPP concentration at low concentrations, but to the first order of the TPP concentration at high concentrations. On assuming two termination reactions, i.e., the usual unimolecular termination by occlusion of the polymer radical and a bimolecular termination between the propagating radical and TPP, and the formation of the weak n-π complex between AN and TPP which accelerates propagation step, the rate of polymerization and the degree of polymerization were kinetically discussed. The equations derived were in good agreement with the experimental results.     

Synthesis and characterization of ordered polyurethanes from nonsymmetric diisocyanate and ethylene glycol

An ordered polyurethane with a head‐to‐head (H‐H) or tail‐to‐tail (T‐T) content over 95% was prepared by polyaddition reaction of a nonsymmetric monomer, p‐isocyanatobenzyl isocyanate (1) with a symmetric monomer, ethylene glycol (2). The model reactions were studied in detail to demonstrate the feasibility of polymer formation. The polymerization was conducted in THF in the presence of triethylamine (TEA) at 0 °C by slow addition of a half amount of 2 to 1, followed by removing THF and then adding the rest of 2 in DMF at once at 30 °C in the presence of dibutyltin dilaurate (DBTL). The microstructure of the polymer obtained was investigated by ¹³C NMR spectroscopy, and it was found that the polymer had the expected structural regularity. The constitutional regularity of polymers influenced their thermal properties. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2106–2114, 2000     

H_2O/TiCl_4/ED体系引发异丁烯控制正离子聚合中的影响因素研究

在亲核试剂(ED)如吡啶(Py)、N,N-二甲基乙酰胺(DMA)或三乙胺(TEA)存在下,由引发剂H2O和共引发剂TiCl4组成引发体系,在二氯甲烷/正己烷混合溶剂中进行异丁烯(IB)正离子聚合,考察了溶剂极性、聚合温度及异丁烯浓度对聚合反应转化率、产物分子量和分子量分布的影响.试验结果表明,随聚合体系溶剂极性增大,聚合速率加快,相近转化率时聚合产物的分子量分布变窄.随着聚合温度降低,聚合速率明显提高,聚合物的分子量增加,活化能为负值,活性链端发生链转移或链终止等副反应的几率减小,当聚合温度为-60℃时,可以抑制活性链端的β-H脱除反应和链转移副反应,并得到大分子链末端全部为叔氯基团的聚异丁烯(PIB).当[IB]0≤2.5mol/L时,随[IB]0增加,聚合转化率有所增加,聚合产物的GPC谱图均为单峰分布,分子量增大,而分子量分布基本保持不变,对于加入Py的聚合体系,分子量分布指数在1.33~1.45范围内,对于加入TEA的聚合体系,分子量分布指数在1.47~1.60范围内,并求出在加入Py和TEA的聚合体系中活性链向单体的链转移常数CM分别为5.5×10-4和6.6×10-4.     

Vinyl Polymerization Initiated by Ceric Ion–Ethyl Cellosolve Redox System in Aqueous Nitric Acid

Abstract

Polymerizations of methyl methacrylate (MMA) and acrylonitrile (AN) were carried out in aqueous nitric acid at 30°C with the redox initiator system ammonium ceric nitrate-ethyl cellosolve (EC). A short induction period was observed as well as the attainment of a limiting conversion for polymerization reactions. The consumption of ceric ion was first order with respect to Ce(IV) concentration in the concentration range (0.2–0.4) × 10^?2 M, and the points at higher and lower concentrations show deviations from a linear fit. The plots of the inverse of pseudo-first-order rate constant for ceric ion consumption, (k ¹)^?1 vs [EC]^?1, gave straight lines for both the monomer systems with nonzero intercepts supporting complex formation between Ce(IV) and EC. The rate of polymerization increases regularly with [Ce(IV)] up to 0.003 M, yielding an order of 0.41, then falls to 0.0055 M and again shows a rise at 0.00645 M for MMA polymerization. For AN polymerization, R _p shows a steep rise with [Ce(IV)] up to 0.001 M, and beyond this concentration R _p shows a regular increase with [Ce(IV)], yielding an order of 0.48. In the presence of constant [NO^? ₃], MMA and AN polymerizations yield orders of 0.36 and 0.58 for [Ce(IV)] variation, respectively. The rates of polymerization increased with an increase in EC and monomer concentrations: only at a higher concentration of EC (0.5 M) was a steep fall in R _p observed for both monomer systems. The orders with respect to EC and monomer for MMA polymerization were 0.19 and 1.6, respectively. The orders with respect to EC and monomer for AN polymerization were 0.2 and 1.5, respectively. A kinetic scheme involving oxidation of EC by Ce(IV) via complex formation, whose decomposition gives rise to a primary radical, initiation, propagation, and termination of the polymeric radicals by biomolecular interaction is proposed. An oxidative termination of primary radicals by Ce(IV) is also included.     

丙烯腈与衣康酸在DMSO/H_2O中的聚合及聚合物性能表征

采用丙烯腈 (AN)与衣康酸 (IA)为共聚单体 ,以偶氮二异丁腈为引发剂在混合介质二甲基亚砜 水(DMSO H2 O)中自由基沉淀共聚合 ,合成了高分子量的聚丙烯腈 .通过正交设计方法研究了聚合反应条件 ,如反应温度、单体浓度、混合介质DMSO H2 O配比等对聚合反应的转化率的影响 ,还重点探讨了混合介质DMSO H2 O配比对转化率和粘均分子量的影响 .采用DSC ,TG ,IR等手段研究了PAN均聚物及 (PAN co IA)的结构与性能 .研究结果表明 ,增加反应温度 ,降低单体浓度 ,降低喂料AN IA配比中IA的含量 ,均有利于提高聚合反应的转化率 .AN与IA共聚反应的转化率随着反应介质中DMSO含量的增加而降低 ,同时聚合物的粘均分子量也降低 .对于喂料AN IA配比中IA含量相同的P(AN co IA)共聚物 ,高分子量P(AN co IA)共聚物比常规低分子量的放热峰起始温度低 ,放热峰宽     

Polymerization of Acrylonitrile Initiated by the System Tetramethyl-2-tetrazene and p-Toluenesulfonic Acid

The polymerization of acrylonitrile (AN) initiated by tetramethyl-2-tetrazene (TMT) and p-toluenesulfonic acid (TSA) in dimethylformamide (DMF) was studied. The polymerization was confirmed to proceed through a radical mechanism. The initial rate of polymerization R was expressed by the equation: R_p = k[TMT]^0.6 [TSA]^0.46 [AN]^1.35. The overall activation energy for the polymerization was estimated as 20.7 kcal/mole. In the absence of monomer, the reaction of TMT with TSA was also studied kinetically by measuring the evolution of nitrogen. From these results and ESR measurement of the TMT/TSA system, a possible initiation mechanism is proposed.     

Vinyl polymerization. Part 268. Polymerization of acrylonitrile initiated by the system of tetramethyl tetrazene and bromoacetic acid

The polymerization of acrylonitrile (AN) initiated by the system of tetramethyl tetrazene (TMT) and bromoacetic acid (BA) in dimethylformamide (DMF) was studied. The TMT–BA system could initiate the polymerization of AN more easily than TMT alone. The polymerization was confirmed to proceed through a radical mechanism. The initial rate of polymerization R_p was expressed by the equation: R_p = [TMT]^0.62-[BA]^0.5[AN]^1.5. The overall activation energy for the polymerization was estimated as 9.4 kcal/mole. In the absence of monomer, the reaction of TMT with BA in DMF was also studied kinetically by measuring the evolution of nitrogen gas. The reaction was first-order in TMT and first-order in BA; the rate data at 49°C were k₂ = 9.1 × 10^?2l./mole-sec., ΔH? = 17.0 kcal/mole, and ΔS? = ? 6.6 eu. In addition, the treatment of TMT with BA in benzene led to the formation of tetramethylhydrazine radical cation, which was identified by its ESR spectrum. On the other hand, the relatively strong interaction between TMT and DMF was observed by absorption spectrophotometry.     

POLYACRYLONITRILE PRECURSORS FOR CARBON FIBER WITH IMIDOCARBOX YLIC ACID UNITS: COPOLYMERIZATION OF ACRYLONITRILE WITH MALEIMIDOBENZOIC ACID

ABSTRACT

4-Maleimidobenzoic acid (MBA) was explored as a comonomer in polyacrylonitrile (PAN) precursors for carbon fiber. The copolymerization of acrylonitrile (AN) with MBA was carried out in DMF. The reactivity of MBA was considerably less than that of AN, which was manifested as a negative reactivity ratio for the former. The r _MBA- values from ?0.24 to ?0.33 and r _AN values of 1.07 were obtained by Kelen-Tudos and extended Kelen-Tudos methods. The penultimate reactivity ratios were determined by both linear and non-linear methods. The values were r ₁=0.0093, r ₁′=0.0132, r ₂=1.063 and r ₂′=1.625. The relative MBA concentration in the copolymer decreased drastically on enhancing its content in the monomer mixture. The penultimate model could satisfactorily explain the feed-copolymer composition profile for the whole composition range. MBA caused a decrease in the apparent copolymerization rate and molecular weight in agreement with the observed trends in the reactivity ratios. A statistical prediction of monomer sequences based on reactivity ratios implied that MBA existed as a lone monomer unit between the long sequences of AN units. This sequence distribution is suited for the efficiency of MBA in cyclisation reaction, which stabilizes PAN during its pyrolysis. Optimum thermal stabilization effect and char yield were observed for copolymers with around 3 mol% MBA in the chain.     

A Study of the Molecular Weight Distribution of Poly(Amino Acid)s Synthesized by Diphenyl Phosphoryl Azide

Abstract

Direct polycondensations of β-benzyl-l-aspartate (Asp.Bz) and β-benzyl-l-glutamate (Glu.Bz) were carried out in the presence of diphenyl phosphoryl azide (DPPA) as a condensation agent and triethyl amine (TEA). Poly(amino acid)s were obtained by this convenient approach whose structure was confirmed by IR and ¹H-NMR spectroscopy. The effects of the monomer concentration, the polymerization time and temperature, the ratios [DPPA]/[monomer] and [TEA]/[monomer], and the solvent used on the molecular weight distribution of the polymer were studied. When the monomer concentrations were higher than 0.2 g/mL, poly(Asp.Bz) with a bimodal molecular weight distribution was obtained (M_w of 37,000 and M_w/M_n of 1.68). The polycondensations carried out in THF or in bulk provided the highest molecular weight (M_w ? 40,000). Several other amino acids were also polymerized by DPPA.     

Electroinitiated cationic polymerization of styrene in the presence of ferric chloride

The electroinitiated polymerization of styrene has been studied in acetone with ferric chloride as the electrolyte. At a fixed monomer concentration, the polymer yield depends on the current strength as well as the concentration of ferric chloride. The molecular weight of the polymer lies in the range of 1000–3000. Addition of zinc chloride to the system or replacement of the solvent by DMF (partly or fully) or methanol retards the polymerization. The current exponent of polymerization is unity with a reaction rate constant of 4.416 × 10^?2 reaction percent per hour. The locus of polymerization is the anode compartment. A cationic mechanism has been proposed for the polymerization, the initiating step consisting of an electron transfer from an adsorbed charge transfer complex of styrene and ferric chloride.     

Poly(vinyl acetate) as a template for the radical polymerization of acrylonitrile

The template polymerization of acrylonitrile (AN) along with atactic-poly(vinyl acetate) of M _v (47,090), at 60°C for 120 min in dimethyl formamide (DMF) has been studied dilatometrically to study the effects of template, monomer, and initiator (benzoyl peroxide) concentration upon kinetics. Viscometric measurements showed that complexation between at-PVAc and PAN was maximum when template/polymer ratio was 1:1 and time required for complete complexation was 15 min. The overall energy of activation was 57.76 and 77.01 kJ/mol in the presence and absence of, PVAc, respectively. The overall system follows mechanism I, i.e., the monomer molecules get adsorbed on the surface of the template macromolecules and then propagation proceeds.     

Polymerization of acrylonitrile initiated by a manganese(III) acetate glycerol redox system

The kinetics of polymerization of acrylonitrile(AN) initiated by manganese(III) acetate in the presence of glycerol was investigated in the temperature range of 30–40°C. The effect of varying the concentrations of glycerol, sulfuric acid, acetic acid, metal ion, and monomer on the rate was studied. A suitable reaction scheme and rate expression have been proposed. Termination was mutual and was caused by the combination of two growing polymer radicals.     

Electroinitiated polymerization of butadiene sulfone

Electroinitiated polymerization of butadiene sulfone was achieved by direct electron transfer in acetonitrile—tetrabutylammonium fluoroborate system by controlled potential electrolysis technique. High conversions were obtained at reasonable temperatures and polymerization times. The polymer was found to be composed of linear segments along with some cyclic units. The effect of monomer concentration, temperature, and polymerization potential on the rate of polymerization was investigated. Temperature and polymerization potential have positive effects on the rate of polymerization. The effect of ultrasonic vibration was also investigated by conducting electrolyses at different monomer concentrations in the presence and absence of ultrasonic vibration. It was observed that the rate of polymerization increases significantly in the presence of ultrasonic vibration. The inverse relationship between the rate of polymerization and monomer concentration was observed in presence and absence of ultrasonic vibration.     

Nanocomposite structures of polypyrrole derivatives and poly (acrylonitrile‐co‐itaconic acid) produced by in situ polymerization as carbon nanofiber precursor

This study aimed to produce nanoparticles of poly (acrylonitrile‐co‐itaconic acid) (P (AN‐co‐IA)) containing conjugated polymers of pyrrole, N‐Methylpyrrole, 2,5‐dimethylpyrrole, and 1‐(Triisopropylsilyl)pyrrole which were synthesized by emulsion polymerization. Nanocomposite structures of P (AN‐co‐IA)/polypyrrole and polymer of pyrrole derivatives were produced via in situ polymerization, and the nanoparticle formation were followed by morphologic and ultraviolet‐visible (UV‐Vis) spectroscopic methods. Characterizations were made by Fourier transform infrared‐attenuated total reflectance (FTIR‐ATR) and Raman spectroscopy. Atomic force microscopy (AFM) was used for investigating the surface characteristics of the nanoparticles. Characterization results revealed that nanoparticles containing conjugated polymers had rougher surface than P (AN‐co‐IA) nanoparticles. It was also observed that the nanoparticles were well‐distributed although having some agglomerates. Moreover, depending on the type of monomer of conjugated polymer, the shape and size of the produced nanoparticles differed by conjunction with their polymerization rate. These findings can be used as a startup information for production of carbon nanofibers (CNFs) with desired properties after oxidation and carbonization, and as a high‐performance and cost‐effective flame and heat‐resistant material (oxidized copolymers of polyacrylonitrile nanofiber).     

Studies of redox polymerization. I. Aqueous polymerization of acrylamide by an ascorbic acid–peroxydisulfate system

The polymerization of acrylamide initiated by an ascorbic acid–peroxydisulfate redox system was studied in aqueous solution at 35 ± 0.2°C in the presence of air. The concentrations studied were [monomer] = (2.0–15.0) × 10^?2 mole/liter; [peroxydisulfate] = (1.5–10.0) × 10^?3 mole/liter; and [ascorbic acid] = (2.84–28.4) × 10^?4 mole/liter; temperatures were between 25–50°C. Within these ranges the initial rate showed a half-order dependence on peroxydisulfate, a first-order dependence on an initial monomer concentration, and a first-order dependence on a low concentration of ascorbic acid [(2.84–8.54) × 10^?4 mole/liter]. At higher concentrations of ascorbic acid the rate remained constant in the concentration range (8.54–22.72) × 10^?4 mole/liter, then varied as an inverse halfpower at still higher concentrations of ascorbic acid [(22.72–28.4) × 10^?4 mole/liter]. The initial rate increased with an increase in polymerization temperature. The overall energy of activation was 12.203 kcal/mole in a temperature range of 25–50°C. Water-miscible organic solvents depressed the initial rate and the limiting conversion. The viscometric average molecular weight increased with an increase in temperature and initial monomer concentration but decreased with increasing concentration of peroxydisulfate and an additive, dimethyl formamide (DMF).     

辐射引发丙烯腈－丙烯酸甲酯－衣康酸三元沉淀共聚合

辐射引发丙烯腈－丙烯酸甲酯－衣康酸三元沉淀共聚合张志成,葛学武,葛敏,张健（中国科学技术大学应用化学系,合肥,２３００２６）关键词聚丙烯腈,超高分子量,辐射引发,沉淀共聚合制备高性能的碳纤维,首先要制备优良的丙烯腈基原丝（ＳＡＦ）．ＳＡＦ聚合物具有超...