多壁碳纳米管/溴/聚苯乙炔三元共混物导电性能的研究

通过机械共混和溶液共混制备了多壁碳纳米管(MWNTs)/溴/聚苯乙炔(PPA)三元复合材料,复合材料表现出良好的导电性能,电导率为10S/m,达到掺溴MWNTs的导电水平.通过固体紫外光谱、XPS和SEM分析了复合材料中MWNTs、溴与PPA三者之间的相互作用,研究了独立导电单元的形成,以及导电单元对电导率提高所起的作用.结果表明,当MWNTs含量较低时,MWNTs和PPA之间的溴转移导致复合材料电导率降低;MWNTs含量较高时,独立导电单元的数目增多,复合材料的电导率随之大幅提高.     

聚噻吩/多壁碳纳米管复合材料的导电性能

通过共混多壁碳纳米管(MWNTs)和聚噻吩(PTh), 制备了PTh/MWNTs复合材料, 复合材料表现出良好的导电性能(电导率达16.1 S/m). 通过Raman, TG, XPS, UV-Vis等对复合材料进行了分析, 结果表明, MWNTs和 PTh之间存在强的相互作用, MWNTs上的离域电子与噻吩共轭主链上的π电子之间形成π-π共轭, 电子从MWNTs转移到聚噻吩, 增加了噻吩主链的有效共轭长度, 提高了复合材料的导电性能. FESEM分析表明, MWNTs和它周围被掺杂的聚噻吩通过π-π共轭作用结合在一起, 形成相对独立的导电单元, 在复合材料的导电体系中起到主要作用.     

聚3-辛基噻吩/MWNTs复合材料的导电性能研究

采用在氯仿溶液中超声共混, 制备聚3-辛基噻吩(P3OT)和多壁碳纳米管(MWNTs)复合材料. 当MWNTs掺杂量为3%时复合材料的电导率为1.43 S•m－1, 达到纯MWNTs的电导率水平. 用FTIR光谱, TG, UV-Vis光谱, XPS和FESEM进行研究分析, 认为MWNTs的离域电子与P3OT主链上的π电子之间形成π-π共轭, 增加了P3OT主链的有效共轭度, 被掺杂的P3OT具有很高的电导率, 提高了复合材料的导电性能. MWNTs与被掺杂的P3OT组成相对独立的导体单元, 对复合材料的导电网络形成起着主要作用.     

聚噻吩/多壁碳纳米管复合材料结构与导电机理的研究

从结构和相互作用方面对聚噻吩(PTh)/多壁碳纳米管(MWNTs)复合材料进行了研究, 结果表明: 一方面聚噻吩本身的结构对其导电性能有一定的影响, 另一方面MWNTs作为一种掺杂剂, 和聚噻吩之间存在强的相互作用, 电子从MWNTs转移到聚噻吩. MWNTs和它周围被掺杂的聚噻吩通过π-π共轭作用形成相对独立的导电单元, 在复合材料的导电体系中起到主要作用, 随着这种导电单元数量的增加直至相互接触, 形成大的导电体系, 复合材料的电导率达到最大值.     

溴蒸气掺杂聚苯乙炔的导电机理

通过溴蒸气的吸附, 聚苯乙炔(PPA)的电导率比吸溴前提高近12个数量级. 采用固体紫外光谱、X光电子能谱研究了溴与PPA之间的p-π共轭效应, 探讨了掺溴PPA的导电机理. 研究表明, PPA掺溴产生了溴负离子和电子转移复合物, 促使导电率提高. 实验证明压力作用的增大有利于增强溴与PPA之间的共轭作用, 温度升高导致掺溴PPA中p-π共轭结构减少, 导致电导率降低.     

聚苯乙炔/碳纳米管复合材料的导电性能研究

本文以无水A lC l3作催化剂合成聚苯乙炔(PPA),用H2SO4对其进行磺化改性,采用其混法制得了PPA/碳纳米管(CNTs)及磺化PPA/CNTs复合材料,对二者的常温电导率及变温电导率进行了测试。结果表明:磺化PPA的电导率较PPA的提高了3个数量级;随着CMTs含量增加,复合材料的电导率升高;PPA/CNTs导电的阈值是3%,达极限电导率(0.04S/m)所需CNTs含量为25%,而磺化PPA/CNTs导电的阈值是2%,达极限电导率所需CNTs(0.14 s/m)含量为25%。并分析了温度变化对复合材料电阻变化的影响因素。     

磺化聚苯乙炔/多壁碳纳米管复合材料导电特性和机理的研究

将磺化聚苯乙炔(SPPA)与多壁碳纳米管(MWCNTs)超声共混制备得到SPPA/MWCNTs复合材料. 用X光电子能谱仪、固体紫外-可见分光光度计、X射线衍射仪、四探针、场发射扫描电镜等对复合材料导电特性及机理进行研究. 结果表明: SPPA/MWCNTs 复合材料中SPPA与MWCNTs发生电荷转移而被掺杂, 并且由于SPPA与MWCNTs间的电荷转移, 彼此间存在一定的相互作用力; 复合材料电阻呈负温度系数效应; SPPA/MWCNTs复合材料电导率发生两次突跃. 可能的导电机理为, 复合材料中SPPA不仅被MWCNTs物理填充, 同时还被MWCNTs掺杂, 复合材料中存在两种导电通路, 一是SPPA与MWCNTs的碳原子发生电荷转移而被掺杂, 彼此之间存在一定的相互作用力, 导致SPPA包裹MWCNTs形成独立导体单元, 这种独立单元相互接触形成导电通路; 二是MWCNTs彼此之间相互接触形成导电通路, 并建立了该导电机理的理论模型.     

磺化聚苯乙炔/多壁碳纳米管复合材料导电机理研究

将磺化聚苯乙炔(SPPA)与多壁碳纳米管(MWNT)超声共混制备得到SPPA/MWNT复合材料. 用四探针电阻率测试、场发射扫描电镜(FESEM)、XPS、UV-Vis、XRD等方法对复合材料导电机理进行研究. 结果表明, SPPA/MWNT的电导率发生两次突跃；掺杂剂MWNT具有低的临界阈值; 临界阈值附近, 复合材料中MWNT具有不连续分布的现象及复合材料电阻呈负温度系数(NTC)效应; SPPA/MWNT复合材料中MWNT的碳原子对SPPA 进行掺杂. 推测复合材料的导电机理为, 共轭聚合物SPPA不仅被导电粒子MWNT物理填充, 同时还被MWNT的碳原子掺杂, 使复合材料中存在两种导电通路而导电, 一是因被掺杂而成为高电导率主体的SPPA相互接触形成的导电通路, 二是MWNT相互接触形成的导电通路.     

聚丙烯/石墨纳米复合材料的导电性能研究

磨盘碾磨固相剪切复合技术(S3C)是制备聚合物 石墨导电复合材料的有效途径,所得聚丙烯 膨胀石墨复合材料具有纳米插层复合结构,石墨纳米片层的相互搭接可形成导电网络,具有纳米间隙的石墨插层结构可形成隧道电流,从而大幅度降低复合体系的导电逾渗阈值,在低填充量实现聚合物复合材料高电导性,与熔体共混相比,导电逾渗阈值由4 .3vol%降低到0 . 5 5vol% ,在石墨含量为4 .0 1vol%时,电导率提高10个数量级.     

氯掺杂提高多壁碳纳米管的电导率

通过氯气吸附, 制备了掺氯多壁碳纳米管(Cl₂-MWNTs)复合材料, 在低温、高温和紫外光照射条件下掺氯, 紫外光照射下掺氯制备的复合材料电导率最高, 和未掺氯MWNTs相比, 电导率提高到原来的5倍以上. 用热重、红外吸收光谱、紫外-可见吸收光谱、拉曼光谱和X光电子能谱分析研究掺氯碳纳米管中氯和MWNTs间的相互作用, 结果表明: 掺氯后MWNTs中π电子向氯转移, 氯与MWNTs形成共轭体系, π电子的离域性增强, 提高了复合材料的电导率.     

多壁碳纳米管与溴的相互作用及导电机理

通过溴蒸气的吸附, 提高多壁碳纳米管(MWNT)的本征导电性能, 加溴多壁碳纳米管的电导率提高了3倍. X光电子能谱、近红外光谱、紫外光谱、拉曼光谱表明多壁碳纳米管与溴之间存在共轭作用, 这种作用导致多壁碳纳米管上的π电子向溴偏移, 产生空穴载流子. 利用半导体能带图, 提出加溴多壁碳纳米管微观体系模型来研究溴对多壁碳纳米管的作用及导电机理.     

Influence of multiwall carbon nanotubes on morphology and electrical conductivity of PP/ABS blends

Polypropylene (PP) and acrylonitrile‐butadiene‐styrene (ABS) blends with multiwall carbon nanotubes (MWNT) were prepared by melt mixing. PP/ABS blends without MWNT revealed coarse co continuous structures on varying the ABS content from 40 to 70 wt %. Bulk electrical conductivity of the blends showed lower percolation threshold (0.4–0.5 wt %) in the 45/55 co continuous blends whereas the percolation threshold was between 2 and 3 wt % in matrix‐particle dispersed morphology of 80/20 blends. Interestingly, droplet size was observed to decrease with addition of MWNT above percolation threshold in 80/20 blends. Further, the bulk electrical conductivity was found to be dependent on the melt flow index of PP. The non‐polar or weakly polar nature of blends constituents resulted in the temperature independent dielectric constant, dielectric loss, and DC electrical conductivity. Rheological analysis revealed the formation of 3D network‐like structure in 80/20 PP/ABS blends at 3 wt % MWNT. An attempt was made to understand the relationship between rheology, morphology, and electrical conductivity of these blends. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2286–2295, 2008     

溴吸附对碳纳米管导电性能的提高

通过溴蒸气的吸附, 提高多壁碳纳米管(MWNT)的本征导电性能,加溴多壁碳纳米管的电导率提高3倍. 通过拉曼光谱, 紫外可见光谱, 红外吸收光谱, 近红外吸收光谱和X光电子能谱等方法研究, 结果表明: 溴与多壁碳纳米管之间存在共轭作用, 使多壁碳纳米管表面的电子云分布发生了变化, 导致空穴载流子的产生, 增加了载流子浓度, 提高了多壁碳纳米管的导电性能.     

Rheology,electrical conductivity,and the phase behavior of cocontinuous PA6/ABS blends with MWNT: Correlating the aspect ratio of MWNT with the percolation threshold

Multiwalled carbon nanotubes (purified, p‐MWNT and ～ NH₂ functionalized, f‐MWNT) were melt‐mixed with 50/50 cocontinuous blends of polyamide 6 (PA6) and acrylonitrile–butadiene–styrene in a conical twin‐screw microcompounder to obtain conductive polymer blends utilizing the conceptual approach of double‐percolation. The state of dispersion of the tubes was assessed using AC electrical conductivity measurements and melt‐rheology. The rheological and the electrical percolation threshold was observed to be ～ 1–2 wt % and ～ 3–4 wt %, respectively, for blends with p‐MWNT. In case of blends with f‐MWNT, the rheological percolation threshold was observed to be higher (2–3 wt %) than p‐MWNT but the electrical percolation threshold remained almost same. However, the absolute values were significantly lower than blends with p‐MWNT. In addition, significant refinement in the cocontinuous morphology of the blends with increasing concentration of MWNT was observed in both the cases. Further, an attempt was made to understand the underlying concepts in relation to cocontinuous morphologies that how the geometrical percolation threshold which adversely suffered because of the attrition of tubes under prolonged shear contributed further in retaining the rheological percolation threshold. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1619–1631, 2008     

Synthesis and electrical properties of polyaniline/polyaniline grafted multiwalled carbon nanotube mixture via in situ static interfacial polymerization

The mixture of polyaniline (PANi) and PANi grafted multiwalled carbon nanotube (PANi‐g‐MWNT) was prepared by a two‐step reaction sequence. MWNT was first functionalized with 4‐aminobenzoic acid via “direct” Firedel‐Crafts acylation in polyphosphoric acid (PPA)/phosphorous pentoxide (P₂O₅) medium to afford 4‐aminobenzoyl‐functionalized MWNT (AF‐MWNT). Then, aniline was polymerized via an in situ static interfacial polymerization in H₂O/CH₂Cl₂ in the presence of AF‐MWNT in organic phase to yield the mixture of PANi and PANi‐g‐MWNT. The mixture was characterized with a various analytical techniques such as elemental analysis (EA), Fourier transform infrared spectroscopy (FTIR), wide angle X‐ray diffraction (WAXD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), cyclic voltammogram (CV), UV‐vis and fluorescence spectroscopies, and electrical conductivity measurement. On the basis of TGA analysis, the thermo‐oxidative stability of the mixture was markably improved compared to that of PANi homopolymer. Even after dedoping, in alkaline solution, the mixture would still display semimetallic conductivity (4.9 S/cm). The capacitance of the mixture was also greatly enhanced and its capacitance decay with respect to cycle times was significantly reduced. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1962–1972, 2010     

Preparation,structure, and property of polyoxymethylene/carbon nanotubes thermal conducive composites

Polyoxymethylene (POM)/multiwalled carbon nanotubes (MWNTs) nanocomposites were prepared through a simple solution‐evaporation method assisted by ultrasonic irradiation. To enhance the dispersion of MWNTs in POM, MWNTs were chemically functionalized with PEG‐substituted amine (MWNT‐g‐PEG), which exhibited strong affinity with POM due to their similar molecular structure. The thermal conductivity and the mechanical properties of the composites were investigated, which showed that the thermal conductive properties of POM were improved remarkably in the presence of MWNTs, whereas reduced by using MWNT‐g‐PEG due to the heat transport barrier of the grafted‐PEG‐substituted amine chain. A nonlinear increase of the thermal conductivity was observed with increasing MWNTs content, and the Maxwell‐Eucken model and the Agari model were used for theoretical evaluation. The relatively high effective length factor of the composite predicted with mixture equation indicated that there were few entangles of MWNTs for the samples of MWNT‐g‐PEG in the composites. The mechanical strength of the composites can be improved remarkably by using suitable content of such functionalized MWNTs, and with the increase of the aliphatic chain length of PEG‐substituted amine, the toughness of the composites can be enhanced. Transmission electron microscope result indicated that MWNT‐g‐PEG exhibited strong affinity with POM and a good dispersion of MWNTs was achieved in POM matrix. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 905–912, 2010