Adsorption of strontium from aqueous solution using activated carbon produced from textile sewage sludges

Different types of activated carbons were prepared by changing the activation temperatures (400–700 °C) and impregnation ratio (sewage sludge: KOH; 1:1, 1:2) and the removal of Sr⁺² from aqueous solution was determined. The maximum adsorption yield (12.11 mg/g) was obtained at 500 °C for 1 h carbonization conditions with impregnation ratio of 1:1. The affecting parameters were analyzed by using central composite design method. The selected parameters were initial pH, temperature, initial strontium concentration and carbon dosage. The analysis of variance was performed in 95% confidence level and checked to fitting of experimental value and predicted value. The significant F was P < 0.05 with a model F value of 19.94 which revealed that this regression is statistically significant. The results of regression analysis indicated that pH and temperature parameters were not individually statistically significant for Sr⁺²sorption. However, the efficiency of strontium sorption increases with the increase in carbon dosage and decreases with the Sr⁺² concentration. Influences of initial pH and temperature, pH and Sr⁺² concentration, temperature and carbon dosage and Sr⁺² concentration and carbon dosage on the adsorption process were considered statistically significant. Adsorption of strontium was described by Freundlich isotherm as a physical adsorption (E = 7.2 kJ/mol). The adsorption reactions were calculated as endothermic, spontaneous and favorable reactions.     

Study of immobilized candida rugosa lipase for biodiesel fuel production from palm oil by flow microcalorimetry

Enzymatic transesterification of palm oil with methanol and ethanol was studied. Of the four lipases that were tested in the initial screening, lipase Candida Rugosa (CR) resulted in the highest yield of mono alkyl esters. Lipase CR was further investigated in immobilized form within an activated carbon as support. The activated carbon was prepared by activation physical. Using the immobilized lipase CR, the effects of water and alcohol concentration, enzyme loading and enzyme thermal stability in the transesterification reaction were investigated. The optimal conditions for processing 50 g of palm oil were: 37 °C, 1:14.5 oil/methanol molar ratio, 1.0 g water and 500 mg lipase for the reactions with methanol, 35 °C, 1:15.0 oil/ethanol molar ratio, 1.0 g water, 500 mg lipase for the reactions with ethanol, and 35 °C, 1:10.0 oil/n-butanol molar ratio, 1.0 g water, 500 mg lipase for the reactions with ethanol. Subject to the optimal conditions, methyl and ethyl esters formation of 70 and 85 mol% in 1 h of reaction were obtained for the immobilized enzyme reactions. The flow microcalorimetry is an important and novel techniques is used in evaluation of biodiesel production.     

The superior electrochemical performance of oxygen-rich activated carbons prepared from bituminous coal

Oxygen-rich activated carbons (OAC) were prepared from bituminous coal through a quick KOH activation. OAC exhibited a moderately large surface area of 1950 m²/g, a relative wide pore size distribution, good conductivity and very high oxygen content (up to 12 wt.%). Compared with high surface area activated carbons prepared by the conventional KOH activation, OAC have superior capacitive behavior, power output and high energy density in electrochemical double layer capacitors (EDLC). OAC presented a high specific capacitance of 370 F/g in 3 M KOH electrolyte at a low current density of 50 mA/g and still remained 270 F/g even at a high current density of 20 A/g.     

Adsorption kinetics of various gases in carbon molecular sieves (CMS) produced from palm shell

Carbon molecular sieves (CMS) have been prepared from locally available palm shell of Tenera type by a thermal treatment technique involving carbonization followed by steam activation and benzene deposition technique. Carbonization of the dried palm shells was done at 900 °C for duration of 1 h followed by steam activation at 830 °C for 30–420 min to achieve activated carbons with different degree of burn-offs. The highest micropore volume of activated carbon obtained at 53.2% burn-off was found suitable to be used as a precursor for CMS production. Subsequent benzene deposition onto activated samples at temperature range from 600 to 900 °C for various benzene concentrations have resulted in a series of CMS with different kinetic selectivities. The molecular sieving behaviour of the CMS products was assessed by kinetic adsorption isotherms of O₂, N₂, CO₂ and CH₄ at room temperature.     

A high-performance carbon derived from polyaniline for supercapacitors

Activated carbon derived from rod-shaped polyaniline (the diameter of 170 nm) was synthesized by carbonization and subsequent activation with KOH. The obtained activated carbon exhibits a high specific capacitance (455 F g^?1) and remarkable rate capability due to its high specific surface area (1976 m² g^?1), narrow pore size distribution (< 3 nm) as well as short diffusion length. It is indicated that the promising synthetic method used in this work can pave the way for designing new carbon based materials from different polymers for high-performance energy applications.     

Production of activated carbon from sludge of food processing industry under controlled pyrolysis and its application for methylene blue removal

The present work aims to conduct a process optimization for the production of activated carbon from sludge of food processing industry. The significant feature of this sludge based activated carbon that makes it unique and economic is that it can be produced from waste material. The carbonaceous nature of this sludge does not allow its direct disposal to land because of excess organic and nutrient load contents, however, can be converted to a value added product. This process not only eliminates the need for further treatment of sludge but also reduce the cost of its handling, land filling, and transportation as well as the utilization in the same industry in the purification system.In the present work, activated carbon produced from pyrolysis of sludge was chemically activated by various activating agents. Optimization of impregnation ratio, impregnation time, activation temperature, and activation time was studied. The product was characterized through its iodine value and yield percentage. It was observed that the product had maximum iodine value of 624 mg g⁻¹ with ZnCl₂ as an activating agent. The FT-IR analysis depicts the presence of a variety of functional groups attached on the surface of activated carbon which are used in the interaction with the adsorbate during the process of adsorption. The XRD analysis reveals that the produced activated carbon has low content of inorganic constituents compared with the precursor. The product formed was applied for methylene blue adsorption. The adsorption equilibrium of methylene blue dye was examined at room temperature. Adsorption isotherm was drawn by applying Langmuir and Freundlich models fitting the data indict, with an adsorption capacity of 23.6 mg g⁻¹ and 14.2 mg g⁻¹, respectively. The data show that methylene blue adsorption is best suited to Langmuir equation.     

Preparation and characterization of adsorbents for treatment of water associated with oil production

Two sets of adsorbents were prepared from locally available raw materials, characterized and tested. The first set consists of crushed natural attapulgite and crushed attapulgite mixed with petroleum tank-bottom sludge and carbonized at 650 °C. Another set was prepared using trunk of date palm tree (Phoenix dactylifera) activated at 700 and 800 °C. Both sets were characterized using BET surface area and pore distributions, FTIR, XRD, SEM and TEM. Natural attapulgite and attapulgite/sludge composite exhibited different characteristics and adsorptive capacities for oil removal from oily water. Adsorptive capacities were calculated from the breakthrough curves of a column test. An oily water solution of about 500 mg-oil/L was passed through both the attapulgite and attapulgite/sludge columns until the column effluent concentration exceeded a reference limit of 10 mg-oil/L. Uptake was calculated at this limit at 155 and 405 mg-oil/g-adsorbent, respectively. This was lower than the performance of a commercial activated carbon sample (uptake calculated at 730 mg-oil/g-adsorbent). Relatively, the date palm, carbonaceous-based adsorbent samples showed less significant differences in both bulk and surface properties. Uptake significantly improved to 1330–1425 mg-oil/g-adsorbent. Attempt was made to associate this performance with the difference in the surface areas between the two sets. However, other factors are found to be important as the second set has a range of surface area less than that of the commercial sample. As evidenced by FTIR, XRD and TEM, the activated carbonaceous materials developed porous structures which form defective graphitic sheet ensembles that serve as additional adsorption sites in the sample.     

An activated carbon with high capacitance from carbonization of a resorcinol–formaldehyde resin

A polymeric activated carbon (PAC) was synthesized from the carbonization of a resorcinol–formaldehyde resin with KOH served as an activation agent. The nitrogen adsorption–desorption at 77 K, X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) were used to characterize the prepared PAC. Compared with the commercial activated carbon (Maxsorb: Kansai, Japan), PAC shows superior capacitive performance in terms of specific capacitance, power output and high energy density as electrode materials for supercapacitors. PAC presents a high specific capacitance of 500 F g^?1 in 6 mol l^?1 KOH electrolyte at a current density of 233 mA g^?1 which remained 302 F g^?1 even at a high current density of 4.6 A g^?1. The good electrochemical performance of the PAC was ascribed to well-developed micropores smaller than 1.5 nm, the presence of electrochemically oxygen functional groups and low equivalent series resistance.     

Copper removal from aqueous solution using biochar: Effect of chemical activation

The main aim of this study was to test the efficiency of biochar for Cu removal from synthetic and soil solutions, respectively.The biochar was produced from brewers draff via pyrolysis. Additionally, the prepared biochar was also activated using 2 M KOH to enhance its sorption efficiency to remove Cu from both solutions. Two different aqueous solutions were prepared for these experiments: (i) a synthetic using Cu-nitrate salt with 0.01 M NaNO₃ and (ii) soil solution obtained from a Cu-contaminated soil using 0.01 M CaCl₂ leaching procedure. Batch sorption and column experiments were used to evaluate the efficiency of both biochar (BC) and activated biochar (BC_act) to remove Cu from the solutions.Results showed that both biochar samples are pure amorphous carbon and the Cu sorption is thus mainly a result of physical sorption on the biochar surface. Next, chemical activation, using 2 M KOH, significantly increased the total volume of all pores in biochar (from 0.01 ± 0.002 to 8.74 ± 0.18 mL g⁻¹). On the other hand, the BET surface area was similar for both sorbents (BC = 9.80 ± 0.62 m² g⁻¹ and BC_act = 11.6 ± 0.4 m² g⁻¹). Results also demonstrate enhanced sorption efficiency of the BC_act (10.3 mg g⁻¹) in comparison with the BC (8.77 mg g⁻¹). Additionally, enhanced Cu removal during column retention test was observed for the BC_act in both synthetic and soil solutions, respectively.In summary, the results showed that biochar prepared from brewers draff was able to remove Cu from both aqueous solutions.     

Copper supported on porous activated carbon obtained by wetness impregnation: Effect of preparation conditions on the ozonation catalyst's characteristics

An activated carbon-supported copper heterogeneous catalyst based on (Cu/AC) was developed using a wetness impregnation process. The effect of preparation conditions on the catalyst's characteristics was examined. This work focuses on two key parameters: impregnation rate and calcination conditions (temperature and time). Catalysts were characterized by means of nitrogen sorptiometry at 77 K, Boehm analysis and pH_pzc analysis. It was found that the catalyst properties and the functional surface groups were affected by the operating conditions. The highest measured surface area, i.e. 1040 m²/g, was obtained for activated carbon (AC) impregnated with 12% of Cu loading after calcination at 550 °C for 2 h. The effect of adding copper on the surface of activated carbon on its adsorption capacity was also examined. The obtained results showed that after impregnation, the adsorption capacity of activated carbon was improved. Additionally, the performance of the Cu/AC catalyst on nitrobenzene ozonation was investigated. Our results show that the use of Cu/AC for heterogeneous catalytic ozonation enhanced significantly the degradation efficiency of nitrobenzene (NB) compared with simple ozonation and with ozonation catalyzed by AC without metal addition.     

Highly porous electrodes from novel corn grains-based activated carbons for electrical double layer capacitors

In this study, novel corn grains-based activated carbons (CG-ACs) were prepared and their use as electrodes in the electrical double layer capacitor (EDLC) performed successfully. The structural properties, energetic heterogeneities and surface functional groups of CG-ACs were characterized using different techniques like nitrogen sorption data, adsorption energy distribution (AED) and X-ray photoelectric spectroscopy (XPS). The electrochemical properties of various CG-ACs were evaluated by using cyclic voltammetry. The maximum specific capacitance value as 257 F g⁻¹ was obtained in 6 M KOH electrolyte solution. The effects of various properties of the porous carbon materials on the EDLC performance were discussed.     

Effects of H3PO4 and KOH in carbonization of lignocellulosic material

Samples of lignocellulosic material, stem of date palm (Phoenix dactylifera), were carbonized at different temperatures (400–600 °C) to investigate the effects of their impregnation with aqueous solution of either phosphoric acid (85 wt%) or potassium hydroxide (3 wt%). The products were characterized using BET nitrogen adsorption, helium pycnometry, Scanning Electron Microscopy (SEM) and oil adsorption from oil–water emulsion (oil viscosity, 60 mPa s at 25 °C). True densities of the products generally increased with increase in carbonization temperature. Impregnated samples (acid/base) showed wider differences in densities at 400 (1.978/1.375 g/cm³) than at 600 °C (1.955/2.010 g/cm³). Without impregnation, the sample carbonized at 600 °C showed higher density of 2.190 g/cm³. This sample has impervious surface with BET surface area of 124 m²/g. Acid-impregnated sample carbonized at 500 °C has the highest surface area of 1100 m²/g and most regular pores as evidenced by SEM micrographs. The amounts of oil adsorbed decreased with increase in carbonization temperature. Without impregnation, sample carbonized at 400 °C exhibited equilibrium adsorption of 4 g/g which decreases to about a half for sample carbonized at 600 °C. Impregnation led to different adsorptive capacities. There are respective increase (48 wt%) and decrease (5 wt%) by the acid- or base-impregnated samples carbonized at 600 °C. This suggests higher occurrence of oil adsorption-enhancing surface functional groups such as carbonyl, carboxyl and phenolic in the former sample.     

Valorization of two waste streams into activated carbon and studying its adsorption kinetics,equilibrium isotherms and thermodynamics for methylene blue removal

Wastes must be managed properly to avoid negative impacts that may result. Open burning of waste causes air pollution which is particularly hazardous. Flies, mosquitoes and rats are major problems in poorly managed surroundings. Uncollected wastes often cause unsanitary conditions and hinder the efforts to keep streets and open spaces in a clean and attractive condition. During final disposal methane is generated, it is much more effective than carbon dioxide as a greenhouse gas, leading to climate change. Therefore, this study describes the possible valorization of two waste streams into activated carbon (AC) with added value due to copyrolysis. High efficiency activated carbon was prepared by the copyrolysis of palm stem waste and lubricating oil waste. The effects of the lubricating oil waste to palm stem ratio and the carbonization temperature on the yield and adsorption capacity of the activated carbon were investigated. The results indicated that the carbon yield depended strongly on both the carbonization temperature and the lubricating oil to palm stem ratio. The efficiency of the adsorption of methylene blue (MB) onto the prepared carbons increased when the lubricating oil to palm stem ratio increased due to synergistic effect. The effects of pH, contact time, and the initial adsorbate concentration on the adsorption of methylene blue were investigated. The maximum adsorption capacity (128.89 mg/g) of MB occurred at pH 8.0. The MB adsorption kinetics were analyzed using pseudo-first order, pseudo-second order and intraparticle diffusion kinetic models. The results indicated that the adsorption of MB onto activated carbon is best described using a second order kinetic model. Adsorption data are well fitted with Langmuir and Freundlich isotherms. The thermodynamic parameters; ΔG°, ΔH° and ΔS° indicate that the adsorption is spontaneous and endothermic.     

Novel visible-light-responsive photoelectrochemical sensor of 2,4-dichlorophenoxyacetic acid using molecularly imprinted polymer/BiOI nanoflake arrays

A novel and highly sensitive visible-light photoelectrochemical (PEC) sensor for the detection of 2,4-D has been developed using a nanocomposite of molecularly imprinted gold nanoparticles-polypyrrole polymer (MIP) modified BiOI nanoflake arrays (BiOINFs) as a photoactive electrode (labeled as MIP@BiOINFs). Our results demonstrate that the smart combination of BiOINFs with MIP offers a high-performance photoactive sensing platform. It features the intrinsically excellent visible-light responsive properties of BiOI and prominent recognition ability from MIP. The designed MIP@BiOINF composite dramatically facilitates the PEC determination of 2,4-D. The detection limit for 2,4-D is found to be as low as about 0.04 ng mL^− 1 (S/N = 3). Moreover, the resulting sensor could be used to detect 2,4-D in spiked soil samples.     

The preparation of an adsorbent from mixtures of sewage sludge and coal-tar pitch using an alkaline hydroxide activation agent

The increasing generation of sewage sludge and its subsequent treatment are very sensitive environmental problems. For the more stable and sanitary treatment of this sewage sludge, there have been many studies, including the recent attempt to prepare an adsorbent from sewage sludge via recycling. In this study, of the adsorbent preparation methods, chemical activation was utilized, and in order to find the optimum conditions, several variables were tested, such as the activation agent concentration, activation temperature and activation time. The activation agents used in this study were alkaline hydroxides: KOH and NaOH. The properties of prepared adsorbent were also measured by analyzing the iodine adsorptivity and surface area. In addition, the prepared adsorbent, the BOD, COD, SS, T-N and T-P removal efficiencies from the effluent water of a sewage treatment plant were examined via column test. From the test, the optimum conditions for KOH-activation were 1 mol/l, 800 °C and 1.5 h for the activation agent concentration, activation temperature and activation time, respectively; whereas those for NaOH-activation were 1.25 mol/l, 850 °C and 1.5 h. From the application of the prepared adsorbent to the effluent water of the sewage treatment plant, the measured BOD, COD, SS, T-N and T-P removal efficiencies, the P1-800 adsorbent had the highest efficiencies for BOD, COD and SS of 56.68, 57.76 and 81.45%, respectively.     

Preparation of monodisperse carbon nanospheres for electrochemical capacitors

The efficiently hydrothermal route using sucrose without any catalysts is employed to prepare the uniform carbon spheres. The monodisperse 100–150 nm carbon spheres are obtained with the activation treatment in molten KOH. The carbon spheres are characterized by transmission electron microscope, X-ray diffraction, N₂ adsorption, Raman spectroscopy and electrochemical techniques. The relationships of specific capacitance and surface properties of carbon spheres are investigated. A single electrode of carbon nanosphere materials performs excellent specific capacitance (328 F g⁻¹), area capacitance (19.2 μF cm⁻²) and volumetric capacitance (383 F cm⁻³).     

KOH activated carbon derived from biomass-banana fibers as an efficient negative electrode in high performance asymmetric supercapacitor

Here we demonstrate the fabrication, electrochemical performance and application of an asymmetric supercapacitor(AS) device constructed with β–Ni(OH)_2/MWCNTs as positive electrode and KOH activated honeycomb-like porous carbon(K-PC) derived from banana fibers as negative electrode. Initially,the electrochemical performance of hydrothermally synthesized β–Ni(OH)_2/MWCNTs nanocomposite and K-PC was studied in a three-electrode system using 1 M KOH. These materials exhibited a specific capacitance(Cs) of 1327 F/g and 324 F/g respectively at a scan rate of 10 m V/s. Further, the AS device i.e.,β–Ni(OH)_2/MWCNTs//K-PC in 1 M KOH solution, demonstrated a Cs of 156 F/g at scan rate of 10 m V/s in a broad cell voltage of 0–2.2 V. The device demonstrated a good rate capability by maintaining a Cs of 59 F/g even at high current density(25 A/g). The device also offered high energy density of 63 Wh/kg with maximum power density of 5.2 kW/kg. The AS device exhibited excellent cycle life with 100% capacitance retention at 5000 th cycle at a high current density of 25 A/g. Two AS devices connected in series were employed for powering a pair of LEDs of different colors and also a mini fan.     

Preparation,characterization and application of a CTAB-modified nanoclay for the adsorption of an herbicide from aqueous solutions: Kinetic and equilibrium studies

In this study, surfactant-modified pillared montmorillonites (MMT) were prepared using cetyltrimethylammonium bromide (CTAB) by the intercalation method and used as adsorbent to remove bentazon from aqueous solutions. The main compositions of MMT and CTAB/MMT were characterized by Fourier transform–infrared spectroscopy (FT–IR), X-ray diffraction (XRD), scanning electron micrography (SEM) and energy dispersive X-ray (EDX) spectroscopy. The removal efficiency of bentazon was studied as a function of adsorbent dosage, pH, initial bentazon concentration and ionic strength (sodium carbonate, sodium bicarbonate, sodium sulfate and sodium chloride). The removal efficiency of bentazon by CTAB/MMT was more than that of MMT in similar conditions. By increasing adsorbent dosage and initial bentazon concentration, the removal efficiency was increased and declined, respectively. The results showed that the maximum adsorption of organo-modified montmorillonite was obtained at pH 3. The maximum adsorption capacity was estimated to be 500 mg/g at pH 3 and room temperature. The study of the adsorption kinetic model revealed that the pseudo-second order model was the best applicable one to describe the adsorption of bentazon onto CTAB/MMT. Adsorption data were analyzed by both Langmuir and Freundlich adsorption isotherms and the results showed that it was better described by the Langmuir model. The adsorption capacities of the samples were found to increase with Na₂CO₃ anion saturation, while they decreased in the presence of NaHCO₃, Na₂SO₄ and NaCl.     

The effects of hydrogen on KOH activation of petroleum coke

KOH activation of petroleum coke (PC) was conducted with 30 vol%H₂ + 70 vol% N₂ as carrier gas. TG-DTG, FTIR, elemental analysis, N₂ adsorption, GC and XRD techniques were used to investigate the effects of hydrogen on the activation. During the initial stage of the activation, i.e. the carbonization of the PC, additional CH and CH₂ species were formed due to the chemisorption of hydrogen on the nascent sites of the PC created by the removal of the surface heteroatom groups. The formation of the CH and CH₂ species increased the quantity of ‘active sites’ which is favorable to the further activation reaction, and developed the porous structure of the activated carbons. The micropore volume and BET surface areas of the activated carbon prepared under 30 vol% H₂ + 70 vol% N₂ and with a relatively low KOH/PC weight ratio of 2:1 have been increased from 0.78 cm³/g and 1936 m²/g to 0.97 cm³/g and 2477 m²/g, respectively, compared to that prepared in pure N₂ atmosphere with the same KOH/PC ratio.     

Effect of Bio-based Catalyst in Biodiesel Synthesis

A cost-effective and environmentally friendly biodiesel synthesis has drawn attention in recent research activities. Used cooking oil which is known as waste is used in this study. The objectives of this research were to study an effect of biobased-catalyst which is used as supporting catalyst in simultaneous ozonolysis and transesterification for biodiesel synthesis and to study the effect of two steps process in biodiesel synthesis. The bio-based catalyst used in this process was empty palm bunch ash which was used as supporting catalyst for KOH. Two steps reaction were designed, the first step was run in a reactor at 30 °C with a continuous supply of ozone gas for 3 hours to cleave the unsaturated fatty acids at the double bonds. The second step was a follow up process after the first step without a supply of ozone gas, the temperature was increased up to 60 °C and the reaction continue for two hours. The second step aimed to convert saturated fatty acid which was not yet fully converted at the first step. Results of this study showed that 1.5% of KOH gave better performance in producing short chain methyl esters compared to 1% of KOH in the first step process at various percent weight of ash. The highest short chain methyl esters and long chain methyl esters produced in the first step process were 85.722 mg/liter and 655.286 mg/liter respectively, which was used 17.3 weight % ash and 1.5 weight % KOH. Short chain methyl esters were produced as a result of unsaturated fatty acid cracked by ozonolysis. It is confirmed that a simultaneous ozonolysis and transesterification occurred in the first step process. In conclusion, the presence of bio-based catalyst as supporting catalyst for KOH to produce higher total methyl esters has been effective. The second step process in this experiment was not effective since the effect of reaction time can enhance the hydrolysis of esters as a reverse reaction of transesterification, resulted in loss of esters.