Modeling of half-Heusler crystals with the chalcopyrite structure: Li<Subscript>2</Subscript>MgZn<Emphasis Type="Italic">X</Emphasis><Subscript>2</Subscript> (X = N,P, As,Sb)

A model of Li₂MgZnX ₂ half-Heusler compounds with the chalcopyrite structure is considered. The electronic structure is studied from first principles, showing that Li₂MgZnX ₂ are direct-gap crystals, except for pseudo-direct-gap Li₂MgZnP₂, with a band gap of 2.7 eV, 2.2 eV, 3.3 eV, and 2.5 eV for X = N, P, As, and Sb, respectively. The band structure and chemical bonding in the model crystals are found to be similar to those in LiMgX and LiZnX half-Heusler crystals. Total electron density and deformation electron density distributions are obtained. It is found that Mg–X and Zn–X ionic-covalent bonds are stronger than Li–X ionic bonds in Li₂MgZnX ₂ crystals, which allows Li atoms to move in the space between MgX ₄ and ZnX ₄ cation tetrahedra.     

Rheological study on the cure kinetics of two-component addition cured silicone rubber

The cure kinetics for two-component silicone rubber formed by addition reaction was studied by the rheological method. The influence of reaction temperature (T) on the cure kinetics was explored in detail. It was observed that the data of gel time (t _gel, i.e. the time when the reaction reaches the gel point) or a specific reaction time (t _nc) (defined as the reaction time before which time the influence of confinement of network on the diffusion of reaction components can be neglected) versus T obey certain functional relationship, which was well explained by the cure kinetics model of thermoset network. The cure kinetics for the two-component silicone rubber can be well fitted by the Kamal-Sourour(autocatalyst) reaction model rather than Kissinger model. When the reaction time was before or equal to t _nc, the reaction order obtained by the Kamal-Sourour reaction model was 2, which was consistent with the reaction order inferred from the two components chemical reaction when the diffusion of reaction components was not influenced by the formed cross-linked polymer network. When the reaction time was larger than t _nc, such as to the end of reaction (t _e), the influence of confinement of network on the diffusion of reaction components cannot be neglected, and the reaction order obtained by the Kamal-Sourour reaction model was larger than 2. It was concluded that the confinement effect of network had a greater influence on the cure kinetics of the silicone rubber. The reaction rate constants (k _r) under different temperatures were also determined by Kamal-Sourour reaction model. The activation energy (E) for the two-component silicone rubber was also calculated from the results of lnt _gel, lnt _nc, and lnk _r versus 1/T, respectively. The three values of E were close, which indicated that above analyses were self-consistent.     

Theoretical study on the substituent effect of halogen atom at different position of 7-azaindole-water derivatives: relative stability and excited-state proton-transfer mechanism

We have theoretically investigated the substituted effect on the first excited-state proton-transfer process of nX7AI-H₂O (n?=?2~6, X?=?F, Cl, Br) complex at the TD-M06-2X/6-31?+?G(d, p) level. Here X is the substituted halogen atom, and n value denotes the substituted position of X, such as C₂, C₃, C₄, C₅, or C₆. For the substituted 7-azaindole clusters, 6X7AI-H₂O molecule is the most stable structure in water. The replacement of halogen atom X does not affect the characters of the HOMO and LUMO, but influence the S₀?→?S₁ adiabatic transition energies of nX7AI-H₂O (n?=?2~6, X?=?F, Cl, Br). Our calculated results show that the double proton transfer occurs in a concerted but asynchronous protolysis pathway no matter which H atom is replaced by halogen atom. The halogen substitution changes the structural parameters evidently and leads to amply the asynchronousity during the proton-transfer process. The ESPT barrier height increases or decreases due to the halogen atom and substituted position.     

Electron affinity and substituent effects in radical anions

The first vertical electron affinities EA of 13 series of molecules and free radicals D(X _i ) _n are related to the inductive (σ _I ), resonance (σ _R ^? ), and polarization (σ_α) parameters of substituents X _i by the dependences EA = EA _H + aΣσ _I + bΣσ _R/? + cΣσ_α: In radical anions D^+·(X _i ) _n , compared to radical cations D^+·(X _i ) _n , the polarization interaction is weaker or similar in magnitude but has an opposite sign. The previously unknown resonance parameters σ _R ^? of substituents SiMe₃ and CH₂SiMe₃ bound to the radical anion center H₂C=CH^?· were calculated.     

Observing the orbital ordering of Ti(III) ions in catalysts for the polymerization of diene compounds

The orbital ordering of Ti(III) ions is observed via EPR spectroscopy for the catalytic system TiCl₄ + TIBA in an isopentane solution with an excess of organoaluminum compound. A model of the alternating ground states of 3d ¹ ions (d _xy and \(d_{z^2 }\) is proposed for the ordered structures. Ti(III) ions with the d _xy ground states are mono- and dialkylated.     

Catalytic effects of cationic nanoparticle (CTABr/NaX/H<Subscript>2</Subscript>O,X = Cl,Br) for the piperidinolysis of phenyl salicylate ions

The expression of pseudo-second-order rate constants (k _X) for cationic nanoparticle (CN) [CTABr/NaX/H₂O, X = Br, Cl, CTABr = cetyltrimethylammonium bromide] catalyzed piperidinolysis-ionized phenyl salicylate (PSa^–), at constant [CTABr]_T, 0.1 M piperidine (Pip), and 35°C, were calculated from the relationship: k _obs = (k ₀ + k _X[NaX])/(1 + K ^X/S[NaX]), in which k ₀, k _X, and K ^X/S are constant kinetic parameters and k _obs represents the pseudo-first-order rate constant for Pip reaction with phenyl salicylate ion in the presence of CN. The source of the large catalytic effect of CN catalyst was shown to be due to the transfer of PSa^– from pseudo-phase of the CNs to the bulk aqueous phase through X^–/PSa^– ion exchange at the surface of the CNs.     

Stability of gold(I) glycinate complexes in aqueous solution

The stepwise substitution equilibrium AuCl ₂ ^? +iX^?=AuCl_2?i X _i ^? +iCl^?, β_i, where X^? is the glycinate ion (H₂N-CH₂-COO^?), i = 1 or 2, at 25°C in an aqueous solution with I = 1.0 mol/L (NaCl) has been studied pH-metrically. The corresponding constants are logβ₁ = 3.60 ± 0.10, and logβ₂ = 6.2 ± 0.2.     

Induction of radiative forbidden transitions in an oxygen molecule in O<Subscript>2</Subscript>–H<Subscript>2</Subscript>O collision complexes

By the DFT/B3LYP method the equilibrium structures of oxygen complexes with water are calculated in various geometric conformations with symmetries C _2v and C _s . By the MRCI/CASSCF method potential energy surface cross-sections of the ^1.3[O₂–H₂O] complexation reaction are constructed. With taking into account the spin-orbit coupling, the forbidden transition moments a ¹Δ _g –X ³Σ _g ^?, b ¹Σ _g ⁺–a ¹Δ _g , c ¹Σ _u ^?–a ¹Δ _g , A ³Σ _u ⁺–X ³Σ _g ^? of the complexes are calculated and changes in their intensities at different geometric configurations of the complex are revealed.     

Calculating constants of the rates of the reactions of excitation,ionization, and atomic exchange: A model of a shock oscillator with a change of the Hamiltonian of the system

A new model for calculating the rates of reactions of excitation, ionization, and atomic exchange is proposed. Diatomic molecule AB is an unstructured particle M upon the exchange of elastic-vibrational (VT) energy, i.e., a model of a shock forceful oscillator with a change in Hamiltonian (SFOH). The SFOH model is based on the quantum theory of strong perturbations. The SFOH model allows generalization in simulating the rates of the reactions of excitation, ionization, and atomic exchange in the vibrational-vibrational (VV) energy exchange of diatomic molecules, and the exchange of VV- and VT-energy of polyatomic molecules. The rate constants of the excitation of metastables A ³Σ _u ⁺, B ³Π _g , W ³Δ _u , B′³Σ _u ^-, a′³Σ _u ^-, and the ionization of a nitrogen molecules from ground state X²Σ _g ⁺ upon a collision with a heavy structureless particle (a nitrogen molecule), are found as examples.     

A comparison of energy changes accompanying growth processes by <Emphasis Type="Italic">Saccharomyces cerevisiae</Emphasis>

Calculations are made using the equations Δ_r G = Δ_r H ? TΔ_r S and Δ_r X = Δ_r H ? Δ_r Q where Δ_r X represents the free energy change when the exchange of absorbed thermal energy with the environment is represented by Δ_r Q. The symbol Q has traditionally represented absorbed heat. However, here it is used specifically to represent the enthalpy listed in tabulations of thermodynamic properties as (H _T  ? H ₀) at T = 298.15 K, the reason being that for a given substance TS equals 2.0 Q for solid substances, with the difference being greater for liquids, and especially gases. Since Δ_r H can be measured, and is tangibly the same no matter what thermodynamics are used to describe a reaction equation, a change in the absorbed heat of a biochemical growth process system as represented by either Δ_r Q or TΔ_r S would be expected to result in a different calculated value for the free energy change. Calculations of changes in thermodynamic properties are made which accompany anabolism; the formation of anabolic, organic by-products; catabolism; metabolism; and their respective non-conservative reactions; for the growth of Saccharomyces cerevisiae using four growth process systems. The result is that there is only about a 1% difference in the average quantity of free energy conserved during growth using either Eq. 1 or 2. This is because although values of TΔ_r S and Δ_r Q can be markedly different when compared to one another, these differences are small when compared to the value for Δ_r G or Δ_r X.     

X-Ray diffraction data for new ferrites ErMFe<Subscript>2</Subscript>O<Subscript>5</Subscript> (M = Li,Na, K)

New ferrites ErMFe₂O₅ (M = Li, Na, K) were synthesized from erbium and iron(III) oxides and lithium, sodium, and potassium carbonates by solid-state annealing. According to X-ray powder diffraction, these compounds crystallize in the orthorhombic system with the following unit cell parameters: ErLiFe₂O₅, a = 10.510 Å, b = 10.776 Å, c = 14.270 Å, V ⁰ = 1616.16 ų; Z = 16, V _subcell ⁰ = 101.01 ų, ρ_X = 6.01 g/cm³, ρ_pycn = 5.97 ± 0.05 g/cm³; ErNaFe₂O₅, a = 10.519 Å, b = 10.785 Å, c = 15.510 Å, V ⁰ = 1759.56 ų, Z = 16, V _subcell ⁰ = 109.90 ų, ρ_X = 5.77 g/cm³, ρ_pycn = 5.72 ± 0.08 g/cm³; ErKFe₂O₅, a = 10.050 Å, b = 11.320 Å, c = 15.480 Å, V ⁰ = 1937.33 ų, Z = 16, V _subcell ⁰ = 121.08 ų, ρ_X = 5.46 g/cm³, ρ_pycn = 5.41 ± 0.04 g/cm³.     

One-pot multicomponent synthesis of indol-3-yl-hydrazinyl thiazoles as antimicrobial agents

A series of novel mono- and bis(indol-3-yl)hydrazinyl thiazole derivatives were efficiently synthesized via one-pot cyclocondensation of mono- or bis(indole-3-carbaldehyde), thiosemicarbazide, and phenacyl bromides. The structure of the products was confirmed by Fourier-transform infrared (FT-IR), ¹H nuclear magnetic resonance (NMR), and ¹³C NMR spectra. All synthesized compounds were evaluated for in vitro antibacterial activity against Gram-positive (Bacillus subtilis and Micrococcus luteus) and Gram-negative bacteria (Pseudomonas aeruginosa and Salmonella enteritis). Among the compounds screened, a few were found to be highly effective antibacterial agents. The bis-compounds with OCH₃ donating group exhibited good activity against the Gram-positive bacteria.     

Synthesis and structure of silicon-containing <Emphasis Type="Italic">N</Emphasis>-methyland <Emphasis Type="Italic">N</Emphasis>-benzoylamides of diisopropylphosphoric acid

Diisopropyl N-benzoyl-N-(trimethylsilyl)phosphoramidate reacts with ClCH₂SiMe₂Cl under mild conditions to form diisopropyl N-benzoyl-N-[(chlorodimethylsilyl)methyl]phosphoramidate (III). Diisopropyl N-methyl-N-(trimethylsilyl)phosphoramidate with ClCH₂SiMe₂Cl affords an N-transsilylation product which does not rearrange into diisopropyl N-[(chlorodimethylsilyl)methyl]-N-methylphosphoramidate (XV) even under severe conditions (4 h, 130°C). Compound XV was prepared by the reaction of diisopropyl phosphorochloridate with N-[(methoxydimethylsilyl)methyl]-N-methylamine followed by treatment of diisopropyl N-[(methoxydimethylsilyl)methyl]-N-methylphosphoramidate with boron trichloride. Analysis of experimental and calculated ²⁹Si chemical shifts points to a five-coordinate silicon atom in compound III and a fourcoordinate silicon atom in compound XV. According to B3LYP calculations with due regard to solvent effects, compound III is an isomer with a C=O→Si bond. By variation of substituents at silicon, phosphorus, and carbonyl carbon atoms, chelate structures with either C=O→Si or P=O→Si dative bonds can be obtained.     

Quantitative Structure-Property Relationship: XXIV. Properties of Halo Derivatives of Methane,Silane, and Methylsilanes

The previously suggested structure-property relationship was applied to estimating the properties of methane and silane derivatives C(Si)H _e X _m Y_4?e?m in which substituents X and Y at the same central atom differently interact with each other. In these compounds, the two-fragment 1?3 interactions, multifragment interactions, and interactions corresponding to the electrostatic contribution to intermolecular interactions play a significant role. The boiling points were calculated for the F, Cl, and F,Cl derivatives of methane, silane, and methylsilanes; for the methane derivatives, the octanol-water partition coefficients (log P) systems and heat capacities at constant pressure (C_p) were also calculated. The results obtained are well consistent with the experimental data.     

Theoretical study of stepwise chlorinated aluminide clusters Al<Subscript>13</Subscript>Cl<Stack><Subscript><Emphasis Type="Italic">n</Emphasis></Subscript><Superscript>−</Superscript></Stack> (<Emphasis Type="Italic">n</Emphasis> = 1–9)

The electronic and geometric structures, energy stabilities, normal mode frequencies, and spin density distributions (in radicals) of different stepwise-chlorinated aluminum clusters Al₁₃Cl _n ^? (n = 1–9) are calculated within the B3LYP approximation of the density functional theory using 6-31G* and 6-311+G* basis sets. The results are compared with analogous computation data on hydrides Al₁₃H _n ^? (n = 1–12) obtained at the same level. The general qualitative pattern for related series of hydrides, chlorides, and iodides (as well as fluorides and bromides) turns out to be similar in many respects. For all Al₁₃X _n ^? clusters with different electronegative substituents X, there is a set of a considerable number of low-lying closely spaced inner isomers (with a centered icosahedral cage), marquee isomers, and outer isomers (capped). The effects found by calculations in centered icosahedral isomers—localization of spin density on the trans-Al* atom in radical anions and its associated trans addition rule for an even substituent and the zigzag (odd-even) dependence of the energies D _n (X) of successive addition of substituents X to the metal cage on n described in the framework of the molecular model of the valence states of the Al ₁₃ ^? superatom—should also be shared by many Al₁₃X _n ^? series with different X’s. The differences between hydrides Al₁₃H _n ^? and chlorides Al₁₃Cl _n ^? of the same type are quantitative. For the hydrides, inner isomers are preferable in the first half of the series (n = 1–6); and in the second half (n = 7–12), outer isomers are more favorable. For the chlorides, icosahedral isomers are preferable only at the very beginning of the series. In the other cases, nonicosahedral structures are most favorable, for which the situation becomes very complicated due to the large number of position isomers and the aforementioned simple rules found for centered icosahedral structures are fulfilled to a considerably less extent or not at all.     

Nitration of 3-Methylaceperidazines with a Large Excess of Fuming Nitric Acid

Nitration of N-acetyl-3-methylaceperidazine with a 2–3-fold excess of nitric acid (d 1.36, 1.48) in glacial acetic acid results in the exclusive formation of mono- and dinitroderivatives. The nitration of 3-methylaceperidazine and its N-alkyl- and N-acetyl-substituted derivatives with a 6–9-fold excess of fuming nitric acid (d 1.54) in the same conditions results in the formation of both the expected products of mono- and dinitration and a product of the electrophilic addition of nitric acid to a double bond of acenaphthene scaffold of the molecule of nitration product.     

Predictions of compounds in the family of delafossites

This paper reports the results of our crystal-chemical analysis of structures from the delafossite family A⁺B³⁺X₂, where A and B are cations, and is oxygen. The family is represented by structures of two types, CuFeO₂ and α-NaFeO₂ (R \(\bar 3\) m, Z = 1). Predictions of new compounds are presented. About a hundred new crystals can be synthesized.